Golf IV R32 :: Car Starts Fine But Idle For Seconds And Then Just Bog Out
Jun 23, 2014
I've been having some issues with my mk4 R32. Right now i'm leaning toward changing the fuel pump and filter but i want to be sure before i do.....
Problem: I've been daily driving my r32 to work for the past couple weeks and about once a week it will start, idle for a couple seconds and then just bog out and die. no codes, just idle, then chugging and dying. it will fire with some starter fluid and will sometimes hold a very sickly idle but most the time will just run the starter fluid out. the weird thing is is that it's intermittent and will happen randomly and if i leave it overnight or sitting for a couple hours it will fire up like nothing was wrong. i just wanted some input on what it might be before i replace the pump. i have already done the relay so its not that.... the only code that it has ever thrown while i have owned it was for the intake changeover valve (N156) which i cleared and it hasnt yet to come up again.....
View 14 Replies
Advertisement
A few days ago, I went to start the car, and it will start, and idle fine for a few seconds, and then begin to run crappy, idle down, and die. I tried starting it, and giving it some accelerator pedal, and it dies. I changed the timing belt, idler pulley, and tensioner this summer, so I'm ruling out a bad timing belt. There is no check engine light, and I replaced the plug wires because when I removed the cover, I noticed one of them was worn in a spot, and the wire shielding inside the rubber insulation was visible.
View 11 Replies
Having some problems with my 92 Nissan NX2000. i just finished changing the clutch on the car now its acting horrible.
When i start the car, it will run decent for like 2 or 3 seconds then the idle drops down till it almost dies, catches itself, idle goes up to about 500 were it will pulse around for a few seconds until it dies. If i rev it it will stay running, kept it running for about 2 mins. but as soon as i let off it will pulse at 500 until it dies
After i changed the clutch it started up fine, it ran great for about 20 seconds before it just died. when i started it after is when the problem arose.
I took a video of the car running, which can be seen here. [URL] .... (It has never caught itself like that before and jumped up to 1000 rpms before. It normally will die at that point)
The video is really quiet, not sure what happened there. if need be i can get a video of the engine bay so its louder, was mainly focused on the RPMs.
Here's a few things i tried: Checked fuses, Changed spark plug wires, made sure they were all seated good, MAF wires were rubbed a bit so i cut the MAF pigtail off one of my other sentras and soldered it on,Changed to a good battery, Changed fuel filter, Added more gas (in cause gauge is broken), Made sure all connectors are plugged in, Checked around for vacuum leaks, found that one of the large hoses coming off the intake going to the engine had separated so i plugged them back in and nothing.
View 4 Replies
I have an 04 w12 with 80k miles on it. It will start fine but will not run for more than 10 seconds. As it idles down from startup it settles to about 700 RPM's where it normally does then dies. If u drive it it will start and go into gear fine as u go to pull away it loses all power and dies. I have checked the minor things i know like air filters, oil, tranny juice all appears normal. New batteries less than 3 months ago also.
View 11 Replies
I am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.
What I have done so far:
LH intake actuator arm found broken, replaced both with "Gruvenparts"
Checked all fuses and relays
LH fuel pump reads 14 volts until the relay kicks it off
Tested fuel pressure-good
Batteries fully charged
LH fuel pump reads 0.7 ohms w/key off
RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms
(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)
Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.
Road-tested for 2 hours the next day without any problems.
So, I call the customer to pick it up and he says he will be there 2 days later.
View 15 Replies
I have a 2000 volvo S40 19T, it starts up, and will run just fine if you give it any amount of gas, but it just wont idle. I unplugged the MAF sensor and it ran the same. I then took the IAC valve off and put a towel over the port (To let some gas in but not completely shut it off) It runs GREAT like that! I kept the IAC plugged in and the towel over the port, started her up and put a lot of pressure on the towel to cut of all air, the car idle went really really low and then it shut off. Now since the car knows it is stalling, and it needs more air I should be able to see the IAC opening and closing (Remember it is plugged in, but in my hand), it didn't move at all!
I have run the car with my towel over the IAC ports and chased all around the intake manifold and other intake duct work with carb cleaner to try and fine vacuum leaks to no avail. I even did the towel trick with a multimeter hooked up to the wires that plug into the IAC valve, it is getting a small amount of voltage, say 2 to 3 volts, but the new valve still won't open, and I have yet to confirm that the current changes with idle fluctuations when I press on the towel.
View 4 Replies
2000 f350 CCLB SRW 176,000. I have a touchy accelerator. About two weeks ago the CEL came on and it wouldn't do anything but idle for about 20-30 sec then fine. Then it got a little worse. I disconnected the two harnesses on the accelerator pedal and sprayed them with electrical cleaner. Put it back together and it seemed to be ok. Today the pedal is real sensitive. Sometimes bogging down other times accelerating real high even tho my foot is pretty consistent and gradually accelerating. No CEL tho. Do you think I am in for a new pedal assembly? Could it be something else? UVCH?
View 13 Replies
It is very cold here today about 10F. I started my 2009 Corolla about half hour ago just to make sure it would start. Started fine let it run at fast idle for awhile and shut it off. Went back out to start it again to head out and it will only run very briefly, maybe 1 second or so and then cuts off. It will continue to do that but will start and run normally. I tried for about 10 minutes but didn't want to run down the battery. I hope it is just the cold weather.
View 4 Replies
So, this morning I stopped at the grocery store and when I came back out I started my car. The car ran for about 20 seconds then stalled. Luckily I was able to get the car to the other end of the parking lot for a tow truck yes, this meant starting it about 6 times! This is the second problem in 12 years of owning vw's I'd say that's a good track record! I did a complete auto scan.
View 20 Replies
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
View 2 Replies
.I have an 06 Rabbit and the clutch is not engaging. I woke up one morning to go to work and the car starts fine but won't go into gear. If i jam it in it just stalls out. I know the clutch itself is good since it was running perfect but just now wont engage.
View 1 Replies
Went to start this 5.0 TC after it sat idle for a week, and it died within 3-4 seconds. Further attempts resulted in similar response. After some initial checks, I was able to keep the engine running by manually depressing the IAC plunger into the barrel. The engine ran fine as long as I could hold that, but stall immediately after release. Codes: TPS out of range; HEGO HO2S sensor out of range-always lean. Bought a new TPS no change.
Today: With the key "on" and engine off, the fuel pressure is a steady 38psi. There is an air release button on the fuel gauge line and when I pushed that, the gauge pressure dropped to zero and does not come back (until you key off and on again). I removed the IAC from its mount and with the key on--I observed the plunger move inside its body--guessing maybe 1/4 inch. I casually checked all the engine management items I see in books and looked at vacuum hoses and couldn't see anything amiss (also climbed on top of this engine and checked the rear--PCV lines etc.). I removed the fuel regulator vac line and observed no fuel leakage there.
View 1 Replies
2004 F150 5.4 3v. I bought the truck with 102k on it, it now has 124k. In the morning, when the outside temp is between 30-50, the engine starts and runs fine. When I get to the first red light ( about 1 mile away) within seconds of the engine at idle, engine starts to run rough and CEL. Every time the code is p0351. If I let it sit in the driveway to full warm up... no problem. If I start the truck, shut it off and restart...no problem. It only happens at the cooler temps. I have changed plugs, used motorcraft, nickel antiseize, torqued, etc. Ford changed the coil, I have changed the coil, cleaned MAF. As soon as I cross the intersection, light stays on, rough running clears up, and runs like a champ for the rest of the day.
View 2 Replies
I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
View 4 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
I've shipped my R32 back to the UK, the combination of cold and damp weather has taken it's toll on my car. I started it up Saturday and left it ticking over to allow it to warm up before driving it. The car is used to Houston heat, so a few minutes running will allow the oil to warm a little as the weather here is around 40F at the moment. The car ran for 5 or so minutes, then stalled.
The car starts to about 3 seconds, then dies. I have checked VAGCOM, the only fault is a steering wheel sensor (?). It has a full belly of Shell 99 RON fuel and was serviced just before if left the USA in October.
I have had it towed to the local dealer for repair. I have tried disconnecting the battery for 30 mins to reset the car, it didn't make any difference. I have also tried another key in case it's s sync problem.
View 10 Replies
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies
02 Jetta GLS Turbo 1.8. The car runs perfectly fine, and has good power, but one out of 5 starts at minimum it sets the check engine light exactly 6 seconds after starting the engine. It is most commonly a P0340 - Cam Position Sensor Circ Error, I'd say 70% of the time. The other 30% of the time it is a P0011 - Camshaft Position Timing-Over-Advanced. And once or twice it set a P0012 - Camshaft Position Timing-Over-Retarded. It will only ever set one of the codes. I clear it after it sets, and it will never set the code while driving the car.
- I've double-checked the timing belt, and it is spot on. Could not ask for a more perfect lineup of the timing marks.
- There is no noise or rattle on cold start
- The car carries good oil pressure and I'm on a fresh change with Pentosin 5w40
- I checked continuity on the outer two pins on the cam position sensor with a result of 1.910 ohms.
What I should be looking for next? Almost spent for a new cam position sensor, but hate to throw money if there is something I could test to narrow this down. I can't find any test procedures in the Bentley manuals, but maybe I'm not looking in the right spots. The index has no mention of the camshaft position sensor.
View 8 Replies
During the winter, i always noticed that when starting up the car for the first time, the rpm always jumped high for about 60sec - probably around 1100. i know is normal - just the antichoke kicking in. However, summer is almost here and today was a hot day, and when i started the car and it automatically idled at 600rpm straight away. Is this normal ? or has something happened to my autochoke?
View 8 Replies
I was coming at the climb, my car hit limp mode twice and later I noticed my CEL was on. I let it sit over night when I got where I was going and started it up today started fine but the CEL came on after it ran idle for about 45 seconds. I check the oil and it was on the low end. What it could be?
I drive a mk4 tdi with a malone tune. I am heading back to the valley tomorrow evening I'm just by kamloops right now. Also what oil should I top it with just so it isn't so low for the return trip? (Always get my oil done at the shop)
View 3 Replies
OK, I'm coming to the end of my first month of ownership. Have put on about 1,000 miles (need to drive this thing more - it's so much fun!)
Anyway, once the car is warmed up - I come to a traffic light and sit at idle. Idle starts off evenly at about 700 RPM. After a minute or so, it seems to jump up to about 1,000 RPM. Can feel it "pull" a little. After a bit of time at 1,000 RPM, it seems to drop back to 700 - but not all the time.
Mentioned it to the dealer and got a response like, "they have these things cammed". I don't think it's a cam issue. Just wondering if this is normal behavior or if there is an adjustment or part needed.
View 22 Replies
