Golf IV R32 :: Car Stalls Out Randomly Then Won't Start
Oct 7, 2011
My car runs great, no problems at all. I go for a drive then turn the car off, come back, fuel pump DOES prime when i open the door. Go to start it back up and it starts right up for about 2 seconds, chugs, then stalls out. I try turning the car back on and it just turns over not getting any fuel. wait 5 minutes(once i hear the fuel pump prime again), starts right up.
I replaced my crankshaft positioning sensor and the stalling went away completely... for one week. Today I come out of class, start the car, stalls out and wouldn't start for over an hour. drove it around the rest of the day no problem turning it off and on. its completely random. No check engine light..? fuel relay?
View 24 Replies
Advertisement
I just bought a 2000 VW passat GLS 1.8T, and I'm having a very odd problem with it... I have trouble starting it, almost like the starter is going out, then it starts and runs fine, then I'll be driving and the screen on the gauge cluster will say stop and I'll start getting a beep, if I don't stop the car dies, if I do then it just sort of putters for a second and then goes back to normal, when it dies it loses all power completely everything shuts off then it resets. At first I thought it was the starter, then it started doing this.
View 2 Replies
My daughter's 2008 Elantra starts fine and seems to be idling okay. But recently at seemingly random times the car will stall within a few yards after she starts driving from a cold start. She will start the car, start to drive and then all of the dash lights come on and the engine shuts off. So far she has been able to turn the key and immediately restart the car and then it is fine after that. The problem always seems to occur after she has driven somewhere, let the car sit for a couple hours and then tries to drive again. We took to our mechanic and they said there are no diagnostic codes and the fuel pressure seems good. They did identify some kind of voltage drop/issue with the mass airflow sensor and replaced it. But a day later the problem occurred again. Mechanic seems stumped. I'm very worried about my teenage daughter driving a car that randomly stalls.
View 2 Replies
2001 Excursion 7.3 - stalls randomly, sometimes will not start. After the IPR was replaced it was rough for about 4 miles (I thought maybe air in the system), next 40 miles was flawless with 3 stops and restarts. Then it sat for a few hours and I went to leave again and the problem was off and on again for another 5 mile drive. Now it won't start in the driveway. It will start if I disconnect the ICP but the idle is still a little rough.
I replaced the normal culprits after a lot of searching on here:
CPS - replaced with autozone part, thought maybe it was bad new so went to ford and replaced with official part from the dealer
ICP - had oil in the plug and it would idle better removed so I replaced the plug and as much wire as I could - soldered, heat shrunk, good connections - both the pigtail and sensor came from Ford dealer
IPR - replaced with part from the Ford Dealer (FYI - 1 1/8" 1/2" drive craftsman deep socket from sears fit in the ratchet and on the part).
Grounds - found somewhere that the ground on the firewall for the windshield wipers can interfere with the CPS so I pulled it, clean the connections and made sure it was tight and secure.
No check engine light now - I received a few through the process, but did not clear them and there are no codes at this time (self cleared on the 40 mile drive)
I'm thinking it may be some electrical issue/short or a fuel issue at this point, bowl is full and the filter is fairly new (few thousand miles). I haven't done the Hutch mod, but have over 1/2 a tank.
I'm trying to get this going as quick as I can so I don't want to waste too much time, but I also don't want to miss a critical troubleshooting step to take.
Below are my thoughts on the next steps.
Research and test fuel pressure
Tow it somewhere to test each injector - I only have Torque pro to read codes and engine status
If fuel delivery checks out ok, start testing wire by wire on all of the above parts.
View 14 Replies
So up until a couple months ago my car was running fine. We drove to Vegas and everything was good, then on the way home from the car show, I put some cr@ppy 87 in and about an hour out of town I was going 80 on cruise and it bogged all the way out and came back when I hit like 60. Put some 91 in when I got to the next town and car stopped bogging out after every 5-10 miles.
I got home and read my codes. I've got a secondary air injection issue which has been going on for awhile. Also had a cam position sensor which I fixed.
Now I was driving my car the other day, I drove it til it was all the way warm and then when the clutch gets pushed in and around 1k rpms it stalls. I started it back up with my foot on the floor to get it back going. Right down the street I stop at a stop light and it stalls again and won't start. Had to push it to a gas station and leave it for a couple of hours to wait for it to cool way down to start back up. Was running like cr@p at first, but I made it home.
I had initially thought I needed a new fuel filter as well as a new fuel pump. Heard that it could also be a crank position sensor?
View 6 Replies
Plymouth Grand Voyager has been randomly stalling. If I'm driving the van will auto restart if I wait long enough. If it stalls as I'm coming to a stop it usually will restart without trouble. If it stalls while I'm stopped already then sometimes it refuses to restart. Once it wouldn't restart so the cops push it to a nearby parking lot and then it started right up, as if the move shifted something. Today I had a similar experience, where it refused to start, so I let it roll and abruptly braked and then it started. This problem disappeared during the winter.
View 9 Replies
My husband's 2004 Silverado truck randomly cuts out and stalls. He has replaced sensors and now the computer and it still randomly "dies". Three different mechanics have looked it over and checked the computer codes and can not figure out what is causing it.
View 1 Replies
I own a 2000 nissan altima GXE, and recently i have had a lot of problems, it would stall out randomly and OBD2 scanners said knock senor, EGR, and thermostat. I changed the knock sensor, cleaned the EGR valve and the EGR valve gasket, and haven't touched the thermostat. I changed other things like the crankshaft sensor, fuel filter, fuel pump is fine, alternator, valve cover gasket, and spark plugs. It started stalling all the time after I changed the rotor in the distributor cap, it stalled before but less than after we changed the rotor.
The car would stall randomly when the RPMs would go below 1000. I took it to my friends dad who is a mechanic and he was the one who changed the PCV valve and the EGR valve gasket and cleaned the EGR, he also cleaned the intake and changed the knock sensor. The SES light finally went away but the car would stutter when i would be stopped with the A/C on and i go to press on the gas. once the RPM hit 1000 it would stutter. It didn't stall until a week and a half later. I was told it could MAYBE be throttle position sensor, computer, thermostat, oil loss from valve cover gasket, and idle speed control.
View 3 Replies
I've got 149,xxx miles on my Golf TDI. Took it by a local shop for a routine oil change and since then, it's just been puking oil from the oil cooler. I took it back to the shop and the mechanic even pointed that out. Some red flags here; Timing is too shady. This happened literally the day after the oil change. He also told me that he won't use customer-supplied parts for liability reasons. Seems believable enough, but why would this part just choose to go wrong now?
This is my first time at this shop too and I've never really dealt with "bad mechanics" before but something about this isn't sitting right with me, and I'm not sure how to handle my next step properly. So what would cause an engine oil cooler to leak profusely just after an oil change?
View 1 Replies
Recently my 01 Jetta 1.8T has started to not start like it should. Say every 4th or 5th start it cranks and cranks, I see the tach eventually flick a couple of times and then it finally fires up. It's also stalled while I'm driving, say when I stop at a light but will usually start up again ok.
After the not so good start I get the impression the car is kind of surging while driving - like a fuel supply issue although maybe the fuel pump has nothing to do with supply after starting?
So anyway my thought is perhaps fuel pump issue? I decided to try and search for my issue or fuel pump issues but it talks about things that happen when you open the drivers door which in my case isn't working properly (i.e., I believe it is a DLM as my windows sometimes all go down and I don't get any chime or door light when the door opens).
So just wondering if based on what I'm experiencing if fuel pump sounds likely and perhaps what further tests I should run. My battery is new and the engine does crank pretty good if that eliminate it. I guess I should be thinking fuel filter perhaps also.
View 6 Replies
When the weather gets cold, (lower than 45 deg. F) my Jetta does not want to stay running. It turns over and starts just fine but it does not like to stay on. When I turn the key to the #2 position I can hear the fuel pump fire up and pressurize the system. I always attempt to start it after that, and after 1-2 seconds of running, it seems like it chokes itself out. I have the new coolant temp. sensor (green top), my MAF has been replaced, all spark plugs are new with the correct gap (approx. .030"), new air filter, I run 93 octane fuel.
The worst part is, once the car is warmed up (After forcing it fuel and starting it over, and over, and over again) it runs awesome! I have had this problem since I bought the car (about 2 years ago). The owner told me about it and mentioned that he has never been able to figure it out either (trips to the dealer included). I have been dealing with it for 2 years, but it is getting much worse. Over the past 2 days I have not been able to get my car to stay on long enough to get it to move.
View 2 Replies
My 2000 Volvo S70 just started stalling while driving: it completely dies while in motion. This has happened 4 times in the past week, both times (oddly) in the morning on my way home from the gym. Both times, it's happened we have had very damp weather, and it's the second start-up of the morning. It has happened at slow speeds, and it feels as though it is out of gas, but it is not.
View 1 Replies
I have a 2003 Jetta. It runs great until it just stalls out with no warning. There doesn't seem to be any particular thing I do to make it stall. I could be accelerating onto the highway, just driving down a residential street, moving along at 60 mph, or just starting out of the parking lot. It happens when it is cold and when it is hot. It could happen twice in one day and then not for two weeks. I have taken it to the dealer, a VW specialist, an excellent auto electric specialist, and the local mechanic. No one can figure it out. I have so far replaced the fuel pump, ignition wires, distributor, several engine sensors, complete tune-up, all filters, battery, and some misc wires and hoses. All told, I have spent over $3000. replacing stuff and trying to cure this car's ills. The dealer could not get it to duplicate the stalling. No codes have shown up at the VW dealer, the local guy, and Autozone. The auto electric guy drove it over 100 miles on one week with no problem, then it stalled on him. He immediately hooked it up to the diagnostic machine....and no codes! He was perplexed.
View 7 Replies
2000 Sierra 2500 pickup truck. What would cause my truck to stall randomly and not start? Then after waiting a while it will start.
View 4 Replies
I am absolutely stumped and so are two mechanics I've been to. Randomly when I go to start the car the battery is so dead it won't start. Car is an AWD 2001 1.8T Jetta.
Replaced battery and alternator at my regular mechanic, all ground wires look great and couldn't find any shorts. There is a 11 Amp draw from my battery, took it to a shop that specializes in VW/Audi and they hooked it up to Vagcom and it showed absolutely nothing wrong. He left the meter hooked up and pulled every single fuse in the car and there was only like a 0.01 drop, nothing significant. When he went to take my car out of the shop, wouldn't start. So he put a battery pack on it, still wouldn't start. Took off both terminals on the battery, put them back on, put on the battery pack, and car started.
The aftermarket deck in it is just a JVC single din, doesn't seem to have any issues.
View 8 Replies
I bought this car and I've changed out the Clutch Position Sensor, the black one on the clutch mount. Started to work and start but now it's doing the same symptoms as before. So here is what is going on.
1. Randomly doesn't start, full power comes on, and fuel system turns on, immobilizer works just fine as far as I can tell (key light turns off)
2. Cruise control doesn't work (which lead me to the CPS)
3. High revs between shift, once I push the clutch to shift it revs up high, I noticed that if I stay under 3k it doesn't do it as much, but if I go HAM on it it revs up about 1k rpm more than at shift point. But if I shift nice it revs about 2-400 rpm.
It's been tuned by C2 Motorsports, done by a certified mechanic, that's the only mod on the car, besides suspension. I bought the car and dropped 1100 to fix it to drive right, newish throttle body, and a major vacuum hose, and the tune within a month of getting the car and the tune was to mainly flash the ecu so it wouldn't pull two codes for a leak that wasn't there anymore.
View 5 Replies
have had many problems with my 2003 Accent. I am not a mechanic, but I suspect the problems are related. My engine sometimes stalls when I sit at a red light. I drive about twenty miles to work. On a good day it will just sputter occasionally. On a bad day it will stall as many as three times. It also frequently "skips" a little while driving. It's like a split second hiccup in engine power.
I also used to have a really hard time filling the gas tank. It would take about fifteen minutes when close to empty. I have had it worked on three times over the past three weeks. First they replaced the timing belt (which I already knew needed to be replaced). Then they replaced something called a charcoal canister and blew out all the vapor vents(?) ( Again, I am not a mechanic). After that the car ran ok for about two days, and I can now fill the tank in about two minutes. But, it began stalling again, just as bad as before. So, they replaced something called a MAP sensor (MAFF?).
It has been a couple of days and the car hasn't stalled . . . yet. However, it still skips occasionally while driving, and my engine light has come on again. The mechanic says the code has something to do with a barometric pressure problem. what might be wrong with it?
View 2 Replies
I've got a 99 Ford Escort Se 4 door sedan, Automatic trans with about 140k miles on it that randomly stalls when stopping at a red light. It is random and rare, but it does happen.
When it stalls, it sounds and feels like something is mechanically stopping the engine, like maybe it's not disconnecting from the automatic transmission. I can hear the engine working hard as the car slows down, it jumps around in the engine compartment a little bit, then dies as the car comes to a complete stop.
Then I start the car back up, everything is back to normal and I drive away with no further problems for the rest of the trip.
What can cause this? Does this car have a TCC clutch in the torque converter? Is it maybe randomly being falsely triggered to apply at low speed?
View 1 Replies
I have a 2001 Ford Windstar SE. 220,000 miles. A few months back it started missing ... I drove it like that just local for a few days but then I was leaving town for about a month and just parked it. After I got back I changed the plugs and all was fine on the test drive (ran perfect ... fixed the misfire). What has happened since then has been frustrating. Althought it runs great, now it stalls randomly and always when it's under acceleration and usually going up slight or a bit steeper hills (think So Cal terrain). It doesn't jerk or miss or sputter ... it just cuts out.
If you try to turn the engine over without turning the key off it won't start. Turn off the key then turn it on and it starts like nothing ever happened. No codes whatsoever. Sometimes you can drive it for 30 to 50 miles or more and have no problems at all, then all of a sudden it will stall in an area that it had no problems with over the previous week or so. It seems to stall out at about the time it wants to shift from 1st to 2nd or from 2nd to 3rd ... or at least that general rpm or accelerator pedal position. It's happened with light acceleration and heavy (pulling a long hill) acceleration. Never at idle or decelerating or just cruising on a flat piece of roadway ... never. It also seems the pedal needs to be at a constant position (not pushing down or letting up but just at a certain position under acceleration). I've had my mechanic with me 3 different times and each time it never stalled with him along. Fuel pressure was fine when he checked it (while driving).
Once in a while it will cut out (just enough to notice) then cut right back in and keep running but most of the time it just cuts out and that's it. I've changed the camshaft sensor, the crankshaft sensor, the PCM relay, the fuel pump relay, the throttle position sensor and the fuel filter. I'm hoping to set it up next week where if it stalls I can call the mechanic and have him come over to where I am and see if a code comes up (and check the fuel pressure also) without me turning it off (since that seems to reset whatever the problems is).
View 14 Replies
I have a 2003 Camry 3.0l v6. Stalls at lights random.
Currently the car stalls at stops but this doesn't happen all the time it can go a month in between the problem occurring its very random. While sitting at a light the rpms drop and then it revs up and cycles like that for quite a while. This will also occur while cruising at a low speed while I'm just coasting the rpms will go up and down. I can compensate while stopped by power braking and keeping it at its normal idling rpm. I have no check engine lights and can't seem to determine what would be causing this issue.
View 5 Replies
I recently purchased a rebuilt 2014 Ford Focus ST3 with about 11,000 miles on it. The engine is a turbocharged 2.0L EcoBoost. I usually use 91 or 93 octane fuel, whichever is the highest available. - 6 speed manual and around 285 horsepower (with tune) is a lot of fun to drive. When I bought it, I had the mechanic that was rebuilding it put an Injen cold air intake on it. A few weeks after I got the car, I took the it to a local performance shop to get it tuned. The tune works great and added a bit of power to the car, but now I have a strange issue.
About 1 time out of 75 when I take off, the car throttle is limited and displays the message "Engine fault - service engine now". On one occasion the engine even stalled on me while crossing a highway. Note that this happens while shifting into and releasing the clutch ONLY on first or second gear. In order to get my car running properly again, I need to come to a complete stop and turn off the engine and then restart it. Sometimes the check engine light stays on, but it usually goes away after I restart. The only engine code that is shown is P106B, which has something to do with an incorrect reading on MAF sensor causing the throttle body to close.
Research online told me this issue is commonly caused by a damaged/improperly sealed intake filter or a crack in the intake itself, which changes the angle that air hits the MAF sensor. I have checked both of these and they are good. I have ruled out a bad throttle body control because if that is bad it usually throws another code indicating that it is faulty.
The only thing that I can think of, and I may be wrong, is that when the performance shop tuned my car they tuned it for a stock intake. This would mean that the car does not think it should be getting the airflow that it is and throttles it down to compensate.
I am not sure what to do at this point because (A) the issue impossible to replicate and seems to happen at random, and (B) I cannot just take it to the performance shop and tell them to fix it because I am not sure what is wrong in the first place.
View 3 Replies
