I have a mk4 r32 with 110,000 miles and I'm throwing a p0016 code witch I believe is cam position sensor my timing chains and guides were changed at 90k car runs good and if I erase the code it doesn't come on right away maybe every 200-500 miles:confused could this just be a bad cam sensor there is also no oil leaking from them and they are tight.
View 14 RepliesI have a 2006 Prius with over 300k miles. I recently started getting the crankshaft/cam position code P0016. The car is driving fine, but it does burn about a quart of oil every 800 miles. It looks like a lower mileage engine can be had for about $500-600 including freight. I'm thinking my best option is probably to swap out the engine. I saw our local resident expert Wong suggested replacing the transaxle too when doing an engine replacement since it does not add any significant labor and tends to be a more common source of problems than the engine. I'm not sure how much doing that would add to the bottom line.
View 8 Replies2004 VW R32, No engine mods. I did have the vacuum line sealed off for the flapper mod for about 3 months but is is now back to normal.
I've got the MIL, ESP, and EPC lights on and scanning codes as follows:
Code-P0222
Definition:
- Throttle pedal position (TPP) sensor/switch "B"
- Circuit Low
Explanation:
- Open or short circuit condition
Probable Cause:
- Poor Electrical Connection
- Faulty TPP sensor
- Faulty throttle valve control module
I don't know much about the situation but I took it to my friends shop first where we replaced the Throttle body, intake, and MAF. Didn't fix the problem so I took it to my local VW dealership and the tech's exact words were.."the codes coming up as a throttle pedal sensor. Is there perhaps a sensor by the pedal that I could check?
Am getting an EPC light + limp mode + code for accelerator position sensor (implausible signal). I have swapped out the pedal assembly, so it isn't the sensors themselves, and we've checked the wiring to the pedal assembly... I can feel in-car, and I can see via VAG-COM that one of the two sensors is basically toggling between a sensible % reading of pedal position at one moment, and then zero % the next, and of course every time the sensor reads zero, the ECU notes the error and cuts power... but this only happens when the steering wheel is straight or when turning to the right; I can drive around in a leftward circle all day and night without this occurring.
Why? What is there in the steering (either in the column or at the wheels, or basically any place in between) which, if malfunctioning, could affect the accelerator position sensors in one way or another (i.e. either through the normal operation of a safety system, or through a short or other electrical gremlin)?
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesI have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
I've tried to do my due diligence searching on this (I've seen many posts but most have other codes).. I have the P000A code, reads as follows-- Intake (A) Cam Position Sensor Slow Response (powertrain).
I have no misfires, hesitation rough idle, nothing. I have 94k miles and I always done my oil changes @ 5k intervals and I have not had any prior engine maintenance done to the car....
I took my R32 to the local VW dealer today and they are saying they believe it might be the time chain tensioners. I am wonder if this could be a simple sensor issue since the car runs perfectly fine, I just get the engine light coming back on after 1 to 2 weeks of clearing the code. I have had this issue since January and I thought it might be the cold weather here in WI.
So about six months ago I bought a used 2010 mkvi gti from a small dealer. Now here's my problem. The other day i started my car and it was a rough start. And the car ran rough. I stalled twice trying to back up. Then the car threw a light. I didnt drive it at all. Shut it off and left it. Read the code that night. P0016
Now I know the timing tensioner thing has been beaten to death. So that's my first thought. However, there was never a rattle or a noise. Nothing like that. Is it possible? All four cylinders have compression. About 210psi. I don't know if that is good or bad. Plugs are worn but look good enough. Not too much junk on them. Coil packs look "newer" and they are the "upgraded" versions. Other than the tensioner what else could cause a p0016 failt?
I took the car out for a little spin about 8 miles. We where about .5 of a mile from the house and there is a section where you have to stop on a little bit of a hill. I stalled the car due to the new Dm clutch then headed to the house and the car started to run like crap. I hooked up VAGCOM and had this code:
17748.P1340 camshaft position sensor-G40/ Engine speed sensor-G28: incorrect allocation(#1)
I swapped out the 2 cam position sensors and cleared the code and started the car and it still ran like crap. I just happen to have a new Cam position sensor(hall sensor) so I swapped it out in both cam positions one at a time and cleared the code and the car still runs like crap.
Is there a way to check(test) with vagcom to see if its one of the engine speed sensors?
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesSo my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesI am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesI got a 2004 Nissan Sentra and a p0335 (Crankshaft Position Sensor) popped up on it after the car stalled out sitting in a parked position for 2 mins. The car also stalled out again 20 mins later while I was driving. When the car stalled out in park I had to wait 3 mins because it was just cranking over, when it stalled while driving it started 30 secs later with 1st turn of the key. This car has been having start up issues after the car been driven and sat for 40 mins but when the key is cycled 3 times it starts up fine. I also was going to eventually make a post of this, the car been making clicking or rattling noise at times, off and on mainly when the car been warmed up and at idle more noticeably heard , hear the noise better from inside the car, forgot what side of the engine where the noise is coming from. Also I did a search in the past about recalls on this car and there was a recall on the CRANK ANGLE SENSOR on the 2.5L engines, the car I have is a 1.8L. Stated on this link 3rd one down. [URL] ... . Does it sound like the Crankshaft Position Sensor needs to get replaced?
View 19 RepliesP0340 code appeared on my camry 07 said cam shaft position sensor was bad what other things can be the problem ? Also I just replaced alternator because car wouldn't start with out getting jumped once I replaced alternator it started up good for a couple of days then when I wanted to start it up it would crank then stop and crank again till it would turn on also car stereo would turn off while running and dashboard gauges would go off and would make the gauges go Dow to zero then it would go back to normal while still driving.
View 1 RepliesI am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesI have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 RepliesThe computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
My wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 Replies2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies