About two weeks ago I purchased an intake from a member here on vortex. I installed it, drove the R a few times, and ended up getting a CEL right afterwards for P0103 (maf circuit high). Does this have anything to do with the intake install? Car runs absolutely fine.. no weird issues. Never heard of an intake causing a code like that. Cleared it.. it came back.
View 4 RepliesSo i got the UM tune done to my car then went and got my TT cams installed. After giving me car the 50 miles to adjust for the cams i get a CEL P0103 Mass or volume air flow circuit high input. Checked the connections around the maf and im noting seeing any broken vac lines or anything out of the ordinary.
Cleaned the maf and cleared the code but the CEL popped back up, got a new maf just because I like spending money on things i dont need and the CEL is still there, low speed or high speed it will pop on.
Is there anything I am missing that could be causing this problem or something i can try other then take to the place that did my cams?
2004 r32
123k miles on it
UM NA tune
carbonio CAI
TT cams
Test pipe and neuspeed cat back exhaust
I recently replaced my MAF on the car with part number 06A 906 461 A which is not the 07D 906 461 part number. I take it that this is wrong because i am getting power surging in the car at WOT and I have a pending DTC code P0103.
View 1 Replies124k, original owner, no mods. Car was running rough and stumbling a bit. A bunch of codes came up. I replaced coils because I had them, spark plugs look good. One code came back p0103. I cleaned the throttle butterfly and replaced the maf sensor. Still same problem.
When I first start it cold it idles high but stays running , once it warms a little the idle drops and then it won't stay running. Then the traction control light comes on and then the cel. I checked for a vacuum leak but came up with nothing.
I went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 RepliesI have a problem with my sonata NF 2006 the check engine light turn on like 2 days ago and give me the p2128 code say Accelerator pedal Position Circuit - High Input something like that i cheek all the cable off the throttle body to the ecu and i don't see any cable broken how I can check the accelerator pedal sensor? I see in one page a texting the sensor whit a multi miter but was for santa fe and the cable don't have the same colors . I need the accelerator pedal cable diagram and i don't have it ....
View 2 RepliesEngine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 RepliesHave a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
I'm getting a weird code on my engine it's p1298 which is electric load detector circuit high input and I'm also getting 3 misfire codes but the car runs great what can I do to fix these.
View 10 Replies2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 RepliesI'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
I have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 RepliesI have an 2004 Santa Fe and im having some Mass Air Flow Sensor problems but I dont know what's wrong. My engine light came on for the second time after awhile. And I got it checked for the code and of course it was my sensor again. The first time I just giggled it around and the light went off. I did the same thing today with giggling it again went off. So I feel like it might be a loose connection but I really hope it isn't failing because im pretty sure that's uber expensive to fix.
View 2 RepliesI keep having the P0102 (MAF Circuit Low) code come up. I've replaced the MAF twice already. I also have the P0113 (Intake Air Temp Sensor) which has been replaced as well. Could the breather hose coming off the Intake Air Duct leading to the oil cooler cause this.
View 1 RepliesSo today i got my first check engine in the .:R. I was merging onto the freeway and i shifted into third rather enthusiastically (didn't redline in 2nd but i was probably at 6k rpm) and put it into 3rd gave it the gas and the tires squealed and I got the traction control light. Has me a little worried since the traction control light didn't go off afterwards. Got off the freeway and pulled into a parking lot and turned it off for a minute and when i started back up I got the check engine light also. Went to schmucks and pulled the codes and the only code I was able to pull up was P0102 MAF circuit low. I highly doubt my traction control light has anything to do with the MAF circuit. I notice when in 1st and 2nd gear (can't really tell about beyond 2nd because there is too much road noise) there is a slight whine. I cleared the codes and the check engine came back but the traction control light never went off.
View 9 Replies2001 jetta 2.0 VW guys a while back I was pulling a code saying that the air temp sensor circuit was low I believe it was P0112 so I replaced the maf with a bwd maf. Said it was for the car. Was fine for a day but now it has a P0102 code and the epc stays on (rough idle) what could be wrong ? Is it because the car hasn't learned the new sensor yet because I've only drove 10km or do I have a faulty sensor. BTW replacing the maf fixed the P0112 code
View 5 RepliesI have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 RepliesI have a 2001 Kia Sephia that quit running as I was driving down the road. The car has a little over 150,000 miles on it and was running fine prior to the incident. The car was responding fine and then suddenly acted as if it lost power and shut down as I was driving. I put a code scanner on the car and retrieved the following codes: 342, 460, and 713, which I understand are the camshaft sensor circuit low input, fuel level circuit malfunction, and transmission temperature circuit high input. Is this a computer that has failed or just all the sensors at once failing? If it is the computer, which one(s)? I was trying to do research and if I saw right, there are more than one ecm's now on cars.
View 13 RepliesI have a 1996 Saturn SL1. The SES light came on and I scanned it. First the only code was p0112. I replaced the IAT sensor. The light remained on, scanned again and the code told me to replace the Idle Adjustment valva. I replaced that, SES was still on. Scanned for the third time and it told me to replace the sensor in the exhaust. Replaced that, SES still was on. Scanned and got code for Intermittent Voltage problem with IAT. Drove 60 miles (as recommended) and that code and SES light went off for a few miles and then the original coded p0112 came back on. Pulling my freakin' hair out! Was told to check voltage at the connector cap of IAT. I did and found continuity to ground but no input signal voltage (5v I was told). Stripped the wires back behind the connector cap and still have no voltage from the PCM. My questions are:
1. When does the PCM send the 5v signal voltage to the IAT? When you start the car or later in the drive cycle?
2. My car has shifted badly for a while (small hitch when shifting into reverse after car is warmed up, not when cold). I found a thread that told that the 5v signal circuit could also be utilized by other sensors, one of which affects the transmission shifting.
3. Could the PCM be out? Would the car still run if it was out.
P0073 Ambient air temperature sensor circuit high. Preliminary inspection, right outside mirror badly damaged/broken. Guess where the sensor is?
View 6 Replies