My airbag light went on so i scanned for codes and I got:
00592-seatbelt switch:right (e25) 32-00-resistance too high.
What I need to do to fix this and make the light go away?
Well, I bought a used 2003 Escape for my daughter and without thoroughly researching the airbag light, now have a problem. The light flashes twice, pause, then once, so I think this is error code 21? I cannot find anything on what this code is and how to fix it. I disconnected battery for an hour and now I get 4 flashes, pause, 6 flashes, 46 error.
View 1 RepliesI had been having battery issues with my 97 ford f150 4.6 liter for the longest time, thought i had a short under dash, i pulled entire dash out, disconnecting bat first of course, and inspected all wiring harness connections and fixing my issues and putting it all back together. now with new bat and all put back together i am now getting the airbag light flashing 5 times then 2 times (error code 52) i know it has some thing to do with power failure or backup battery, but now with the new battery in i cant seem to get it to reset. How to do this?
View 3 RepliesI have a 97 Ford Explorer and the air bag indicator started to flash a code 45. What is this code and what do I need to do to clear this problem?
View 5 RepliesI just pulled error code B1944 from my 96 Explorer. It says
Crash sensor ground
Ckt 1, High res/open
I found the airbag diagnostic module (in passenger cowl area) and checked for loosed wire, nothing found. Where the loose ground wire is located? I checked under the seat (didn't do a through job, but looked).
I was cruising down the highway and my check engine light came on. I was a few minutes from a auto store and they said my code was p1296. I found out it is either the thermostat or the coolant temperature sensor. I wanna know where it is located in the engine bay. I have a 02 VW Jetta 1.8T.
View 1 RepliesI'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 RepliesSo tonight I took apart my glove box and center console in hopes of relocating the TPMS button...Once I put everything back together the MFD says airbag error and when i sit in the passenger seat the airbag icon in the center console is flashing and a 2 and a X. Also the airbag icon is on the dash.
View 13 RepliesI have a 2012 passat se and the airbag error light came on, after it did all the buttons on the steering wheel and the horn stopped working. How is the best way to fix this?
View 4 RepliesMy seat belt latch is throwing the common error:
1 Fault Found:
00591 - Seat Belt Switch; Driver (E24)
32-00 - Resistance too High
I measured block 2 and found that wiggling the seat belt latch showed a 'On' vs 'Too High'. So I know it's that switch inside the latch. I don't want to buy a new latch. But since I always wear my seat belt I could just use a resistor to set it to 'ON' at all times.
I have found a few DIY, but thing seem to vary from R32 to Golf. In this .pdf, it is for the airbag defeat, but I am thinking this is a different issue all together.. [URL] .... This guide then shows different wires than the R32... [URL] .....
I picked up a 2016 CSG GTI S 4-door with DSG on Dec 31st. I had an Airbag Error! message come on when I started it this weekend. I went through several cycles of restarts and it didn't go away. I did a quick Internet search and didn't hit on any common problem with airbags, seatbelt pre-tensioners, etc. I called that Saturday and was given a Monday appointment. I was dreading them having to take out interior dash, seats, trim, etc. to troubleshoot. I just got the call that the problem turned out to be with an airbag sensor connection in the front bumper and it is ready to go. Can't wait to get back to driving!
View 5 RepliesWell, I recently had the "Airbag Fault" error message (along with the wonderful amber airbag light) both appear on my dash, and oddly enough, I haven't hit anything or bumped anything or done anything that could cause this error. I drive a 2001 VW 1.8T and she only has 48,000 miles on her.
View 1 RepliesSo of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
2004 Chevy Suburban 4wd
My airbag light is on and my code reader, Innova 3160d, is telling me that the B0083 code is the Second Row Left Seatbelt Load Limiter Deployment Control (Subfault).
I Googled the code and came up with 1) passenger seat position sensor, and 2) front impact sensor 1 (driver's side).
Which one is correct?
My 09 Camry was involved in a frontside impact crash about 2 years ago, I've had the car fixed since then by a body shop. However, my airbag light has been on for several months and will not go off. I've even had someone at a local garage try to turn it off, but it did not work.
Today a friend of mine used a clip to read the airbag code, and we got the code 31. I'm not sure what this means though.
I have a Air Bag Light on and Code B1811 2007Camry, same thinking clock spring?
View 1 RepliesI have a 2009 Toyota Prius. The airbag/srs light came on a couple weeks ago and would come and go. Eventually it came and did not go. This didn't really bother me as I don't drive it much anymore and I figured it would be gone by the next time I went to start it up. (I also heard about connections under the seat being loose and hoped that was the problem.) Well I was wrong. Today I noticed it was still there so I decided to start diagnosing. I jumped the connector as my obd2 scanner only reads regular and abs codes (not srs apparently).
The only code that came up was 51. Which is the driver side squib circuit. Many say that code 51 usually just ends up being the spiral cable. I simply find this odd as every button on my steering wheels works. Cruise control works fine etc. Idk how only 1 or 2 wires get messed up in that thing and how they turn out to be the ones for the airbag but I suppose its possible. My next step is to take a continuity tester to the 2 plugs that connect to the airbag to see if they are getting power.
06 Camry, ~130K miles.
So the Airbag warning light in my Camry has been coming on (and staying on) intermittently, but would turn off if I turned off the car and restarted it. May take a cycle or two, but it would turn off.
Took it to the dealer, they isolated to the passenger side seat. They cleaned contacts, reseated connectors etc.. and the light stayed off for a while. By the way, there appears to be no relationship to anyone sitting in the passenger seat, or not, at the time.
Happened again maybe 3 weeks later. Same thing was done at the dealer.
Took it in today with light on, they pulled the code B1826 (Description: OPEN IN SIDE SQUIB (P SEAT SIDE) CIRCUIT)
This is my wifes car (and kids) so no airbags isn't an option. According to the documentation I got from the tech at the dealer, the Detecting Condition is:
The airbag sensor assy center receives an open circuit signal in the side squib (P seat side) circuit for 2 seconds.
Side squib (P side seat) malfunction
Airbag sensor assy center malfunction
The "Trouble Area" information:
Front RH seat assy (Side squib (P seat side))
Airbag sensor assy center
Floor wire No. 2
I am getting a CEL and the error code is p2187 engine too lean at idle. I have been reading around to try and find the issue, some seem to say PCV could be the issue. I have also read a test would be try and remove the oil cap while car is idling. I did this test and the oil cap was difficult to remove and the idle got really rough once removed.
View 2 RepliesMy r is throwing a p0601 sum error. I clear, it comes right back. I know the previous owner has it chipped at a garage that wasn't linked to any brand. I was planning on putting an apr/giac tune over it but now I can't (no money). I know this might mean I need a new ecu. Right now I plan on going to vw on monday and having them reflash the ecu bringing it back to stock...if it returns then i guess i need a new ecu... This sound right?
View 5 RepliesI've got a golf tdi with a tune and straight pipe exhaust, and after I hit about 115mph I get a system error code. When I shut of my car, it dissapears and when I try to find it with a code reader, its no where to be found. What's the cause?
View 6 Replies