So I replaced the engine and trans engine mounts on my 2004 R32 today. After I got done and drove it there was some serious vibration and gear whine. It also seemed like I wasn't able to transfer all the power to the wheels, it was definitely slower to accelerate. Did something go out of alignment?
View 10 RepliesSo I replaced the engine and trans engine mounts on my 2004 R32 today. After I got done and drove it there was some serious vibration and gear whine. It also seemed like I wasn't able to transfer all the power to the wheels, it was definitely slower to accelerate. Did something go out of alignment?
View 2 RepliesI recently had my rear engine mount replaced on my 2004 Acura TSX. It was originally identified by the original dealer as requiring replacement and when I took it to anther Mechanic he also verified this and during the replacement he showed me the original engine mount which had a definitive crack.
After installation the Mechanic indicated that the car would feel a little stiff for a while and would smooth out over time. What I found after the first couple of days is that the engine seems to have a significant vibration when I am in idle or after I brake. When the car is in motion there is still a vibration but it is not very noticeable. I just remember from prior feel of the vehicle. This vibration did not exist prior to replacing the rear engine mount.
Is this expected to be normal until I put miles on it. The Acura is a 2004 but only has 75,000 miles. I don't drive it very much but I am concerned that the vibration I feel when I brake may be creating additional damage.
Long story short, over torqued the top two stretch bolts and destroyed the threads. We helicoil'ed both holes and put the bolts back in. That was about 4 months ago.
Today both bolts snapped not while moving. We dolly'd the car home and bought a replacement bracket, however all three bolts along the bottom that go into the transmission housing broke off inside.
I'm a tad stuck at this point. I could drill and tap new holes over the existing, but i question whether that is a good idea. My other thought was to get 3 of the larger stretch bolts that go in the top, completely drill out the three that are broken and tap the big ones in. This thought would also require drilling the bracket to make the larger bolts fit.
I lamented in the past a lot of vibrations when the engine was at 3500RPM (in any gear). I read on the forums and many people blamed the aftermarket "EMPI" axles that I mounted too. In fact, my OEM outer CV joints where seized inside the hub/spindle and one of the inner CV joints was clicking; the boots were all worn. This was the reason I went with aftermarket axles. Anyway, I rebuilt the OEM axles by keeping the shaft only, and getting good quality inner and outer CV joints. I finished today to swap back the OEM axles and, finally, no more vibrations!
View 10 RepliesI have a 2000 Jetta with the 2.0 automatic and just like the title states, I have recently developed a engine vibration that is felt at all times. It is much worse when the car is in gear. I only seem to feel it in the gas and brake pedals. It does not seem to depend on speed nor does it only occur at certain rpms. It feels like someone zip tied a vibrating back messager to my pedals. I want to find out what it is because on long commutes my foot begins to feel like its falling asleep. I can visually see the engine vibrating with the car in gear. I am leaning towards motor mounts.
View 1 RepliesJust recently replaced timing chains and clutch on a 2000 VR6, now I have a bit of drive-case whine but in 3rd & 4th gear only? Replaced throw out bearing with new and sachs clutch, Are my transmission bolts too tight or something?
View 2 RepliesI replaced the old auto trans that was slipping in my 2000 golf with a same year auto trans from a beetle. The beetle had 115k miles and the PO toasted the 1.8t. I replaced the TCM also and when I finished the install I took it out for a drive this afternoon and when I shift it into drive it starts out in 3rd. It will manually shift through the gears but it will not shift from 3rd to 4th. Could I have left something unhooked? Is this a solenoid issue?
View 10 RepliesI have an '04 Camry with auto trans that has developed a whine in 1st gear, not noticeable in the higher gears. Is this normal and nothing to be concerned about or is corrective action needed. I have searched other threads but none with this particular issue. I have 50,000 miles and the trans has not been serviced other than checking for normal fluid level and color/smell.
View 14 Replies1999 Jetta MK4 with only 124k miles on it. Everything is fine with the car except when the car shifts from 2nd to 3rd it is jerky/violent/forceful everything else is good with car except check engine light is on but I don't really care about that and I'll go check with autozone to see what the code is. I am able to feather the gas when I know its going to shift and I can make the shift pretty smooth. My question to all the experts is does this mean that this tranny is on its last leg or does it still have a lot of life left in it. My old Cabriolet did it for years and never was a problem.
View 5 RepliesI have an 04 Jetta 1.8T that I recently acquired and have a problem with a noisy manual tranny. Reverse is a bit noisy (more than usual) and when I get on it in 1st and 2nd gear it sounds like an awful whining noise. I have been told it could be either a bad throw out bearing or input bearing? BTW this thing shift perfect, like butter, no grinding at all.
View 4 RepliesI've had a weird problem pop up within the past few weeks. My engine seems to have a noticeable whine above 4000 RPMs. It sounds almost like a supercharger whine, but my engine is completely stock. Possible problems I found online include exhaust leak, vacuum leak or tensioner issue for the belts.
Another issue I have had is that whenever shifting into second gear, I have some difficulty getting it into second gear. It makes a scraping sound as though the clutch is not disengaged all the way. On occasion, I have also had the shifter kind of pop second gear out when continuing onto third or even feel like it is rejecting second gear sometimes. A friend of mine told me that the scraping sound is normal and, "that's just how manuals are." Doesn't seem normal to me especially since it is every time I shift to second gear.
I have an 05 jetta 2.0 and I had a loud whine on passenger side of engine. I removed serpentine belt and ran engine briefly and noise was still there. Figured it was water pump or tensioner. and when I was changing timing belt, tension, and water pump I found it was the timing belt itself that was whining. It was OEM original belt with 140,000 miles on it. The belt was in very good shape no tears just used looking. Now engine is very quiet.
View 1 RepliesAbout a year ago i notice this vibration and took it to my local lexus shop they stated that my engine mount is bad. bought the mount from lexus and change and vibration is still there...,my question is am i the only one that is having this engine vibration problem or this a common problem for the 06-11 awd.?
View 10 RepliesWill overfilling transmission fluid cause hard shifts? I used ~4.3 quarts to refill. How much should I drain out? My check engine light came on.
Basically, I am having hard shifts from 2-3 and 3-4 in tip mode and auto. more tip mode tho.
-I did a complete solenoid change b/c of cold start problem with n92 solenoid.
Fixed the cold start shifting out of first.
-Did a trans fluid change with Mercon V ATF Fluid works fine.
-Just changed oil on 4th of July last week.
Yesterday my check engine light came on. It's been about 500 miles since the solenoid change/trans fluid change, and 100 miles since the oil change.
Now my Mk4 is having this obnoxious shifting. I am thinking I possibly added too much trans fluid into my system as I do not have the VAGcom tool.
I drained out (bone dry drain till no more dripping from check/drain plug), roughly 4 quarts. I added 4.3 give or take 0.1 quarts back into the car.
Now I'm worried because everywhere I'm reading says anywhere from as little as 2.1 quarts to 3.5 quarts.
Should I drain out 0.5 quarts (because I know theres over 4 in there now) to make it 3.5 quarts?
Or should I just redrain the whole thing and start by measure one quart at a time?
Two control arms and a passenger side cv axle I get a bad engine vibration @3800 rpm. Feels like solid motor mounts. It goes away @4500 rpm.
The old cv axle was making noise from the inner joint and the control arm bushings were broken apart.
The engine vibration was not there with the old parts.
When I'm idling and I rev the engine to exactly 1200 rpm i can feel an extra vibration coming from the engine. If i hold it at this rpm it will continue on. now this is not a violent vibration but more so of a buzz i can feel that travels to my steering wheel as well. what could it be ?
Another question is when i travel up my driveway and i hit the sloped curb at a angle i can hear a specific "clunk" sound coming from around the drivers foot well area what could this be? perhaps my axle going bad? I also heard it when I was reversing out of my parking space while turning.
I am new to this car and trying to make sure I'm doing everything i can to put it into good shape.
The following occurs: When car is in PARK there is no strange vibration even with AC on.
When DRIVE is engaged, vibration begins, even worse with AC on. Once the car accelerates vibration is gone.
I went to the authorized dealer service shop and they told me that this symptom is typical of these cars, they even sat me in some other cars to prove that these vibrations are normal.....
What hardware I need to install the passenger side motor mount spacer from Euro Image Tuning. Been sitting on it for a while and cant find the hardware that it came with. Would like to install it, but dont remember what it came with..
View 2 RepliesWas tinkering on my car this morning, and at first noticed one side had a bigger gap than the other. Ok, I really need to change strut mount bushings, no big deal. Then I actually looked closer, and they both have some lean to them, but the drivers side is much more than the other one. Is this normal? I've never noticed any play in control arm bushings or anything. So what could be causing this? I would assume they are meant to sit flat but maybe not?
View 8 RepliesThe other day when i wanted to start the car, I found out my battery was death so i decided to ask my buddy to push me and crank it on gear. Car shakes as normal and engine started, but then i heard a weird noise like if something was rubbing. I turned it off and popped the hood. I found my engine leaning forward and toward the passenger side.
So the next morning, I checked the bay again and i found out that it wasn't the motor mount. Motor mount is ok, but then i found a broken bolt that holds the bracket to the block; the one that goes right next to the water pump to be more specific. Also in the back of the block there is a bolt that hold bracket to the block again and the thread whole was enough weak to break when the other bolt failed. So I did some research and i found that there is a solution for the bolt in back of the block.
What I am concerned is for the on the goes right next to the water pump. It seems that it broke the whole thing including the part where the bolt threads go. I just had a shop install I.E connecting rods, new piston rings, and rebuilt the heads. They put a new timing belt kit and all its job required. I think they might have a bit of fault on this since it had to be removed when they did the timing belt kit. Anyways I don't want to think my block will be a junk now because engine is running like a champ, and that would be a bummer.
-Bolt that is broken in two pieces.-
-And where it is attached to the block-
-Part of the engine where this all goes.-