Golf IV / Jetta IV :: Vibration At 1200 Rpm When Idling And Rev The Engine
Jul 24, 2015
When I'm idling and I rev the engine to exactly 1200 rpm i can feel an extra vibration coming from the engine. If i hold it at this rpm it will continue on. now this is not a violent vibration but more so of a buzz i can feel that travels to my steering wheel as well. what could it be ?
Another question is when i travel up my driveway and i hit the sloped curb at a angle i can hear a specific "clunk" sound coming from around the drivers foot well area what could this be? perhaps my axle going bad? I also heard it when I was reversing out of my parking space while turning.
I am new to this car and trying to make sure I'm doing everything i can to put it into good shape.
View 3 Replies
Advertisement
I have a 1.8t jetta that has a weird idle issue when starting and engine is cold it like to idle at 1200 rpm then will eventually work its way down to 800 rpm
I have no cel codes and have looked for vacuum leaks (but may have missed one) ,but if i start the car and it idles at 1200 rpm then i shut it down and start it right after it will idle at 800 rpm as normal.
Its a 1.8t unitronic stage 1 stock everything except e type coils with plugs at .032, Also does not have much pull after 4000 rpm, not to worried but just may be part of the issue....
View 6 Replies
Driving home from work yesterday I noticed my car started having the vibration on and off during my commute. Traffic most of the time so I could feel it just reving the car up a bit. It happens going up from 600-1200 and back down I can feel it too.
View 2 Replies
I bought a 2005 wagon from a local dealer with 21K miles, the 1.8T, an automatic and 4mo. It was certified and still has 2 yrs and 24K miles on the warranty.
Anyway, I there is a rattle/rumble/vibration anytime the engine is at about 1200 RPM. I usually happens on small inclines, and doesn't matter if you are decelerating through 1200 or accelerating through it is makes the noise. I can get it to sustain itself if i keep it at 1200 on the gas or on the brake.
I am hoping it is just a heat shield that rattles at the certain frequency the engine makes at 1200, but I don't know. It is kind of right at that point where the transmission engages and disengages, torque converter?
View 1 Replies
After about a 45 minute drive yesterday the EPC light came on, idle went up to 1200 rpm's and when I turned off the car it wouldn't turn on, just leaving the ignition for about 5-7 seconds is when the car finally started.
Today, again after a 45 minute drive the EPC light came on again, same symptoms, except that the car stalled and I had to turn the ignition again about 5-7 seconds for it to start. No other light is on, and the car would start fine after about half an hour rest with no EPC light.
View 1 Replies
Recently I believe i got a tank of bad gas. Was having problems starting. Finished it off filled up used injector cleaner and dry gas to clean it out a bit more. Now as I was driving the car would basically stall out but kick back in as I was driving and the EPC light would come on. I've been reading up and most answers are a bad coil pack. I pulled them all out and checked them they all look pretty good. No codes are popping up for it a coil pack. Unless I need a specific VW model computer to check. I'm gonna check the volts on the coil packs today to see as well.
The EPC light does go off after the car sits a while. It comes back after a few miles driving. After the EPC light comes on my car will idle at 1200 RPMs up from 800 when its normal.
View 4 Replies
Vehicle: 2006 Mk IV Golf 2.0 GLS With 82766 mi
Back story: I purchased the vehicle from my dad who did regular maintenance except that somehow spark plugs and wires slipped through the cracks until now. A few months ago (while I was in training) it apparently started showing CEL but the few times it came on, my wife said it just disappeared. Two weeks ago, it came on again and I had the code read which came back as P0420. I took it in and they replaced the rear cat after which it ran well for a few days. Then the CEL came on again but went off before I could get out in the shop. This weekend I went ahead and changed the oil and may have over filled it slightly. The next day I went to change the spark plugs and after changing 4, 1, 3 it started to miss fire in 4 and 1. I reset both spark plugs and got 4 firing again, but 1 remained bad. With a friend I determined there was a weak spark in 1 and changed the wire but no change.
Current situation: As it stands now, it's still miss firing. The worst seems to be between 1200- 1800 rpm and if I keep it above there the light will stop flashing and even turn off on some cases. I've read that heart mixed with moisture(I just moved from AZ to WA) can lead to a cracked coil pack or that the injectors can go bad. Should I just take it to vw specialist?
View 5 Replies
I have a Golf GTI IV 1.8T Tiptronic and having this problem when the car is Idling i can feel the engine vibrations trough the seat and are anything but soft, especially if the trany is neutral and less if leave it in D.
I've changed the dog bone recently, wich was very bad, but the vibrations didn't smooth they remain the same but the driving improved, so the dog did replacement was good.
The next step would change the engine mounts, but they look goof and I don't want to start change parts just in case. Where I live car parts aren't cheap and some times new ones are just crap.
View 1 Replies
I have a 2003 golf 1.8t and the car shakes when launching from a stop. it shakes as long as the rpm is below about 1200. i have an o2 b1 s1 error. also the car is not performing well and seems like it doesn't have enough boost although the boost is reaching its max amount. the car is mapped at 1.3 bar. so does the o2 sensor cause such issues or is it something else ??
View 7 Replies
I have a MK4 Golf 2003 1.9Tdi PD100 , the problem is that the engine seems to miss when idling , so the question really is how can I tell which cylinder is missing , it seems to do it every 10 seconds or so and the engine shakes slightly at the time as if it were missing ! .
I suppose it would be easier if the cylinder was missing all the time , then maybe I could crack open a line at a time ! , but can you do that on a PD engine !
View 1 Replies
My 1999 BMW 3 series, with 112K, full synthetic oil and a 5 speed transmission does great, except for one minor issue. About once a week, when the motor is warm, it dies. Tonight after driving it about 20 minutes on the highway I came to our hill, put it in 1st gear to come up (like always), and then came to the flat part where I put it in neutral to coast the few feet into our driveway. The car responded by idling up to about 1200 RPM, and then dying. It always starts right up the 1st time (even after sitting for 2 weeks), and it is absolutely otherwise reliable. My initial thoughts were something with the idle control valve?
View 1 Replies
My 1997 f150 5.4 has started an idle issue. The truck when started will idle around1200 rpm and not settle down After driving a bit it will drop down around 800 and idle rough and sounds like it has a plug fouled. As soon as you give it gas it clears up and sounds fine, then drops down an idles rough.
Checked for vacuum leaks but don't see any. pulled the MAP sensor and cleaned it, but did not change.
View 7 Replies
Two control arms and a passenger side cv axle I get a bad engine vibration @3800 rpm. Feels like solid motor mounts. It goes away @4500 rpm.
The old cv axle was making noise from the inner joint and the control arm bushings were broken apart.
The engine vibration was not there with the old parts.
View 16 Replies
I lamented in the past a lot of vibrations when the engine was at 3500RPM (in any gear). I read on the forums and many people blamed the aftermarket "EMPI" axles that I mounted too. In fact, my OEM outer CV joints where seized inside the hub/spindle and one of the inner CV joints was clicking; the boots were all worn. This was the reason I went with aftermarket axles. Anyway, I rebuilt the OEM axles by keeping the shaft only, and getting good quality inner and outer CV joints. I finished today to swap back the OEM axles and, finally, no more vibrations!
View 10 Replies
The following occurs: When car is in PARK there is no strange vibration even with AC on.
When DRIVE is engaged, vibration begins, even worse with AC on. Once the car accelerates vibration is gone.
I went to the authorized dealer service shop and they told me that this symptom is typical of these cars, they even sat me in some other cars to prove that these vibrations are normal.....
View 8 Replies
I have a 2000 Jetta with the 2.0 automatic and just like the title states, I have recently developed a engine vibration that is felt at all times. It is much worse when the car is in gear. I only seem to feel it in the gas and brake pedals. It does not seem to depend on speed nor does it only occur at certain rpms. It feels like someone zip tied a vibrating back messager to my pedals. I want to find out what it is because on long commutes my foot begins to feel like its falling asleep. I can visually see the engine vibrating with the car in gear. I am leaning towards motor mounts.
View 1 Replies
I am hearing a vibrating sound only between 2000 - 2500 rpm while accelerating from inside/under engine bay. No impact on ride quality and no engine harshness is felt. Only it sounds like some metal sheet is vibrating for a while. After crossing 2500 rpm it simply disappears.
Checked inside the engine compartment by revving the engine while stationery and I don't get that sound. What could it be? Some shield of the exhaust? cat?
View 2 Replies
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
View 14 Replies
So I replaced the engine and trans engine mounts on my 2004 R32 today. After I got done and drove it there was some serious vibration and gear whine. It also seemed like I wasn't able to transfer all the power to the wheels, it was definitely slower to accelerate. Did something go out of alignment?
View 10 Replies
I own a 2.4L Automatic 2003 Camry XLE.
I've gone to multiple mechanics and none have been able to give me a clear answer. Long story short, I've just recently had a new engine put in.
While it runs fine, there is a tremendous amount of vibration coming off the engine. You can feel it while it's idling, and at all RPMs. It kinda bearable at 1,500 and is the worst at 1,800 RPMs. Beyond 1,800 RPMs, it doesn't get worse, its kinda tapers off just a little.
Notes:
- We've checked the balance shafts and they are aligned correctly.
- No engine code
- Replaced spark plugs
The vibration is bad enough that some screws inside the car have even become loosened. As I said in the beginning, I've gone to multiple mechanics and no luck. What it could be and what to do/try.
View 5 Replies
My 2010 ES350 now has about 52K miles. Recently, it has developed a vibration in the steel wheel when the engine is idle. It used to be very smooth. I wonder what has caused the vibration.
View 8 Replies
