Golf IV / Jetta IV :: Very Hard To Get A Smooth Shift From Gear To Gear
May 28, 2007
Background facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
View 9 Replies
Advertisement
I've just got my 2015 GTI a few months. I'm driving manual with my GTI daily commute to work, getting along well. However sometimes I'll be struggling with the manual when approving a corner or a stop, and I'm not having a smooth up shift with 3rd and 4th gear (odd eh? most of the people will have difficulties starting up but since I've been taught so I'm fine...)
To be more specific:
1. Just want to know what REV usually will be done? e.g. 3rd gear with decent speed, would you maintain it until it revs up to 3k? or would you up shift when passing 2k+? Usually I'm doing the latter so I guess this is why I'm having a sluggish/jerky up shift with 3rd and 4th gear. And would you still put on a little bit gas when engaging with 3rd and 4th gear?
2. What to do when approaching stop? Assuming you don't have enough distance to down shift each gear. EITHER: Break with the current gear and clutch in until it reach 1k rev and complete stop; OR: down shift at least once to a lower gear and break until complete stop?
View 24 Replies
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
View 6 Replies
I had my shift fork and 1 and 2 gear synchros replaced. Whenever i shift into second it doesnt feel as smooth as first. when i hold the clutch longer and put it into second it feels smoother.
View 2 Replies
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.
View 22 Replies
2011 TDi 6 Speed (Sportwagon) with problems shifting into 2nd? Mine is currently in the shop under investigation for a balky shift when cold. The tech says it's not right, but then they find another vehicle in inventory with the same issue...currently waiting on a VW engineer.
View 16 Replies
So i was trying to adjust my freinds shift linkage on his o2j and i got a little ahead of myself and forgot to put the shift tower in the home position before making the adjustment. after i realized you can't shift into second ( either that or 2nd and 4th are extremely close together now and feel like the same gear ). I try to get it in home position even with the cables off ( did this for experimentation) and still wouldn't go into home position...meh. still have all the other gears including reverse .
View 4 Replies
Started noticing an issue with my trans awhile ago, the other day it stopped shifting out of first when cold. It's a 1.8T auto 5 speed tiptronic, it's the Jatco 09A. I know the shifting problem is the solenoids and it doesn't look that hard to swap them out. The trans shop said it looks like there is slippage on gears 2-4 and the fluid is toast. Looking at replacing or rebuilding, shop said 4-5 grand, how easy would it be to swap in a used trans? And what kind of issues would I be looking at?
View 1 Replies
I replaced the old auto trans that was slipping in my 2000 golf with a same year auto trans from a beetle. The beetle had 115k miles and the PO toasted the 1.8t. I replaced the TCM also and when I finished the install I took it out for a drive this afternoon and when I shift it into drive it starts out in 3rd. It will manually shift through the gears but it will not shift from 3rd to 4th. Could I have left something unhooked? Is this a solenoid issue?
View 10 Replies
My wife and I recently purchased a 2013 Jetta and have noticed some abnormal lag when accelerating. It's an automatic transmission and the gear shifts aren't as smooth as they should be. I have read that it is possibly related to the drive by wire system and may just be an inherent result of that system.
View 4 Replies
My buddies Jetta won't shift into high gear. I am going to take a look at it this saturday to find more out.
View 4 Replies
When I'm driving, the Jetta will sometimes not shift from 3rd to 4th gear, so I just turn of the car a start it and it seems to work, but eventually does it again. Once it is in 3rd gear it does not downshift and stays in 3rd even when stopped. The trouble code is P0785 which is the shift/timing solenoid. Not sure if I need to get a new part or which solenoid to get. Also I cannot figure out where this solenoid is actually located or what it looks like.
View 1 Replies
Okay so I bought this car and a week later tranny wouldn't shift out of first when I would slow down or at least it would take a min. I would hit 4or 5 grand then it would jolt me back. It wouldn't do it every time though. I bought it to go to college drove it the 900 miles on the highway and had no problems except right before I left town but then fine. All I did was change the tranny fluid before I left which I can confidently say I don't think has been changed before that. stunk bad bud no metal.
Alright now I'll go jump in the car to go to class and it will not leave first. If I put it in the manual mode it thinks it's in third but clearly if in doing 15 mph at 4000 rpm that's not the case. It doesn't do it every time. Kinda hit or miss. After driving for a min it usually shifts. Sometimes I make it the two miles without it shifting though. Also sometimes It will shift but once I slow down it won't shift out of first again.
I have seen a code for torque management since I bought the car. The check engine light is on now but I haven't seen the torque code since I change the MassES. that's not to say it's not still there. I used a different handheld computer for the check engine light the last time I did it and I could have missed it because I was unfamiliar with it. I have put a mass airflow sensor, battery, alternator, and changed the tranny fluid since I have owned the car. drained 3L of tranny fluid and put 3L back in. Oh and the last time I checked the light it said lean in bank 1 but I was assuming that was an unrelated issue.
View 6 Replies
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
View 5 Replies
Just bought this car yesterday. test drive went fine with no issues. Started driving it home and the check engine light came on ( no big deal i thought car runs great). I go to advance auto and their scanner won't hook up to it. So i start looking at the fuses and everything was good except it was missing the the number 7 fuse ( reverse lights/speedometer sensor), so i replaced the fuse. i get home and i decide to take it down the road one more time and it all went down hill quick. EPC light came on, the car wont shift out of first gear (automatic). so i let it sit over night with the number 7 fuse out and the battery disconnected. CEL never disappeared this morning and its do the same thing. It looks like the MAF was just replaced and the brake light switch looks like the newer green version. Im going to replace the brake light switch this afternoon and i already cleaned the MAF. Another thing that i noticed that is very strange is now the Foot symbol by the shifter has gone out. The one on the dash still is working properly but the one at the shifter does not light up at all now.
View 1 Replies
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
View 10 Replies
I have 2002 1.8t jetta 5spd with 200k KM, last winter it was difficult getting into gear when it was cold. the fluid has never been changed, so that might be the issue.
View 4 Replies
Have a question when I shift slow from 2nd to 3rd my o2j tranny doesn't grind but when I shift fast from 2nd to 3rd it grinds it happens starting at 3000 Rpms thru 6000 Rpms. It also doesn't happen when I shift from 4th to 3rd. Have performed a tranny fluid change. Along with replacing the clutch at 1500 miles ago. The engine is AWP.
View 4 Replies
Got a 2001 Jetta 2L automatic 200k miles with gremlins. possibly multiple unrelated problems. First problem that presented is that the transmission will occasionally not shift into 4th gear. I discovered that if I stop the engine, then restart it, it will again return to normal operation, hence the thought that it is electrical. After a year or so of this, second problem pops up: the engine will die while the car is driving, or some times idling at a light. I've also noticed that the interior lights flicker somewhat in intensity when on and the engine is operating, so there could definitely be a grounding issue somewhere. I have heard that the ECU/ECM connectors could become corroded, but haven't yet dug into it to look. Any guesses as to where to begin?
View 2 Replies
Drove my 02 VW golf GL to the airport, it sat there for 4 days, drove it back home. Next day I noticed that my 1st gear and reverse are very hard to get into. So I kept messing around with it and noticed that if I tried to put it slowly into first gear that there was no way in hell it would go, it felt like the gear was closed.
But if I put it into second gear and push it from second gear into first gear it goes back into first gear about 70% of the time. And it will also go into first gear if I push my stick down as if I'm attempting to go into reverse, and slowly move it into 1st gear.
The reverse is also very hard to get into it feels just like the 1st gear does when you try to do it slowly, it's like it's closed off/blocked. Latest work that was done to the car, replaced the clutch about 4-5 months ago.
View 2 Replies
1999 Jetta MK4 with only 124k miles on it. Everything is fine with the car except when the car shifts from 2nd to 3rd it is jerky/violent/forceful everything else is good with car except check engine light is on but I don't really care about that and I'll go check with autozone to see what the code is. I am able to feather the gas when I know its going to shift and I can make the shift pretty smooth. My question to all the experts is does this mean that this tranny is on its last leg or does it still have a lot of life left in it. My old Cabriolet did it for years and never was a problem.
View 5 Replies
