Golf IV / Jetta IV :: Vacuum Leak From Brake Booster?
Apr 19, 2015
I need replacement vacuum hose part for my GTI 337. The piece that is disconnected is the hose from the break booster to the intake manifold. It appears to be at a one way valve. I found a picture from a different DIY, that I have circled in green. The red arrow points to the place where it separated. I am not sure if this is a matter of me using a new clamp or buying a new piece of hose from advanced auto parts. The vacuum sets on ECS Tuning and it doesn't appear to be the correct set.
[URL].........
View 2 Replies
Advertisement
Brake pedal whistles and is hard to push. Only happens intermittently. Mechanic wants to put new brake booster on. This would be 3rd brake booster in 9mos. It's gotta be something else. What does the vacuum hose connect to from the check valve; where on the intake manifold? If no PVC valve...then what else? Truck runs fine...no fast idle or rough idle and no hesitation.
View 4 Replies
How do you remove the brake booster rod from the brake pedal? The damn rod won't separate from that plastic housing. I've tried wedging a flathead in there but it's hard to see. I've been fighting with it all evening and finally gave up before I end up breaking it.
Found a DIY that just cut the rod to pull the brake pedal to remove it. I rather not do that as I will be reusing the one I have.
View 8 Replies
After replacing the engine, clutch and pressure plate. Where the brake booster hooks up to create a vacuum, as I now have a very hard to push brake pedal, if indeed that is my problem. The pedal will not go down more than one half inch.
View 5 Replies
Was wondering if it is safe to use seafoam through my brake booster vacumm line? If I drip it in SLOW can I still hydrolock my engine?
View 15 Replies
Brake booster failures on 2011 and newer F-250's? I purchased a 2011 last august and the mechanic at the dealer I purchased the truck from stated that he had replaced the vacuum pump, vacuum brake booster and brake master cylinder on the truck just before I bought it as they were bad. Since then I have had two factory Ford vacuum Boosters fail on me. That makes at least three new factory Ford booster assemblies in this truck within the last year. What could be causing the problem? The truck is out of warranty and I am at a loss as to what could be causing them problem. Too much vacuum? Luckily the last two boosters have failed while sitting in a drive through and at a stop light, otherwise I may have had trouble stopping.
View 3 Replies
I suspected I had a vacuum leak somewhere, was told it wasn't likely. Just installed a tune in the evening drove it 15 miles was pretty sure I had one.
Installed Forge DV the next morning it was evident I had one by the sound the DV was Making. I checked the car head to toe and found two lines had broken apart. I replaced them will silicone lines and it appeared to be fixed.
Drove it 5 miles and the 'turkey sound' came back. (This is the sound that I originally heard and confirmed I had a vacuum leak somewhere)
I searched all over there car, had a second set of eyes that was mechanically inclined and we found nothing obviously causing a problem. We ended up just taking off the Forge DV and testing it by hand it held up and re installing it and securing it.
Strange enough that fixed the problem (no other hoses were tampered with while we were inspecting)
Drove the car home about 15 miles and stopped in a drive through. At some point while sitting something happened. Cause when I left the drive through then I noticed the car seemed to be lacking at low end, turned down the music and I could hear the turkey call. I left the car alone for the night. Thought maybe heat jas a factor in this. Drove it this morning and it was just how I left it. I inspected the hoses and found no change. I took the DV off and inspected then re installed. I noticed the turkey call was not as predominant but still completely present.
View 7 Replies
Ever since I got my car about 5/6 months ago I noticed it's not getting full boost. when I first got it the stock boost was getting about 5-7 I don't know if that's normal I've read they normally get more. eventually I got my car tuned and it's supposed to peak at 22 psi but it only got to about 13-14 psi. slowly it's been getting worse and my car is getting 2 psi. I've had lots of people tell me it's a vacuum leak. also the bov makes a flutter noise if that has anything to do with it. my intake doesn't make a sucking in noise like most do. The car has been randomly backfiring usually between gears. I just ordered a turbo inlet pipe a breather hose kit and a boost hose kit.
View 4 Replies
As title states, I scanned my gti and got P0420 (nothing new here) and P1136. I did some searching and looks like vacuum leak can cause this, however I also read that it'll affect my idle. I replaced MAF 2 years ago with a brand new OEM one, my idle is NOT rough, at all.
View 1 Replies
I just bought a 05 1.8T Jetta 116,000miles. and need diagnosing it. It misses all the time. Has new plugs I tried two other sets of coils (from my 2.0 a4 and my dads passat) and it made no difference. The SAI was taken out but nothing is blocked off. Also the coil pack wiring harness has cracks on the big brown wire where it goes down along the block. I'm getting these codes on my vag-com.
16687 cylinder 3 misfire
16686 cylinder 2 misfire
16688 cylinder 4 misfire
17766 cylinder 2 open ignition circuit
17763 cylinder 1 open ignition circuit
17769 cylinder 3 open ignition circuit
17772 cylinder 4 open ignition circuit
So am I correct in thinking that it's from the cracked harness? An not a vac leak?
View 4 Replies
Question, I have a 2003 VW Golf GLS 2.0L AHV (5 speed). The brake vacuum line is cracked after the check valve on the intake side. I looked up the part number on the hose (at work and don't have it on me at the moment), did some research and noticed some revisions to that part number. Eventually settled on [URL] ..... (I ordered a new one since I needed to order a few things). Needless to say, I am beginning to think I ordered wrong.
I noticed that the check valve on the new hose has a 3rd piece that a smaller hose looks to clamp on? The check valve that is in my car doesn't have that. Did I order the wrong part? or did I need to be a cap?
View 3 Replies
Want to replace vacuum booster with electric vacuum pump.
View 4 Replies
Haven't found any other useful info on this, but local dealer says that's where my truck is leaking oil from, and since it's considered brakes not powertrain the repair won't be covered under warranty ...
Backstory goes : dropped my truck off at local dealer Thursday to repair an oil leak from near front main seal area of the engine discovered while inspecting to initiate a bumper-to-bumper warranty through Ford ESP- their platinum warranty. I figured with all the electronic widgets and non-powertrain stuffs on this beast I wouldn't mind paying for 3yrs/36k miles of trouble-free motoring, y'know?
Apparently it's the O-ring on the brake vacuum pump that's allowing engine oil to leak. I can't even find this thing, just looking for some further explanation. I'm keeping an open mind so far, I don't suspect the dealer's just trying to get one over on me, just trying to be good and educated before I go plunk down for the repair.
View 14 Replies
My wife was driving my 93 Volvo 940 wagon yesterday, and the brakes suddenly lost power, and brake lights went out. I have heard no hissing from the booster, and I have checked the 10 amp fuse on the relay beneath the instrument panel. Hoping (and praying) it is just one of the relays. I have a meter, but not sure which pins to use to check the relays. Secondary issue: the used radiator I bought did not have the cooling fan sensor, so I have my fan on a toggle inside.
When my wife pulled over because of the brakes, she did not turn the fan on. Yup. Overheated. Now the radiator leaks from the rubber/plastic plug where the sensor goes. Any pliable sealants that could withstand the temps? Cash is in very short supply right now. That is my main issue right now, trying to drive with no brake lights. No ABS light, and no brake light coming on on the dash. Bulbs are good. ABS light does not come on at all with ignition, but bulb tests good. Just hard brakes, and no brake lights.
View 7 Replies
Recently bought a MKV R32. Already had a magnaflow cbe, k&n panel filter, and some emissions stuff taken out from under the hood. not sure if it has been flashed, waiting to get a vagcom. think it is pretty stock other than that. My problem is about 2 weeks after I got it, I started to notice an exhaust leak or vacuum leak or both at higher RPMs, like above 3 or 4k it starts. The exhaust has a nice deep rumble in normal driving but when the leak noises start that is all you hear, the exhaust note disappears completely. I have tightened the clamps on the cbe and still does it. Not sure what to look for.
View 3 Replies
I have a vacuum leak on the driver side seal on the changeover rod in the intake manifold. It was replaced recently at the dealer and now has another hole in it. I was told this is caused by oil in the lines and my pcv valve is bad.
View 1 Replies
Car: 2011 VW GTI MkVI
Mileage: 79k
Configuration: Stock
Warranty/Coverage: None
So I started my car last Monday and the check engine light was on. Didn't think much of it because the car ran fine and there were no immediate symptoms. I was busy with work this week, but noticed some changes in the car's performance over time so I waited till Thursday to have it scanned at AutoZone, which threw the following codes:
P 300 Definition: Random Engine Misfire
Explanation: Lean air/fuel ratio
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 302 Definition: Cylinder 2 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 303 Definition: Cylinder 3 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
Prior to making any purchases I noticed that I started losing some pickup, primarily in lower gears between 2-3k RPM's. Praying that it was somehow just the coils/plugs I bought the R8 pack for both and replaced them this evening. Engine starts up and continues to misfire. I have not had a chance to have it scanned but it would appear it isn't the plugs or coils.
When the plugs were removed, there was an 'oily' substance on the threads, which also seemed like it could have been burnt off fuel or oil pushed up from the cylinder. Also 2 of the plugs seemed looser than the others and didn't feel properly sealed. New R8 install included proper plugs for STOCK application, as I do not run any tuning, and i installed with the appropriate plug grease added lightly to the threads.
I took the car for a spin with the R8 coils/plugs installed to compare it to how the car was doing prior the install. Car misfires and seems fine (relatively) at idle and revving to 2-3k rpm yields NO change. It is almost unable to accelerate up a hill, or go past 30 MPH without the car shaking and any gear higher than 3rd seems not drivable. I feel these are my potential diagnoses before i bring it somewhere and have it looked at.
In Order of Most Likely:
1) Fuel Injectors
2) Air Intake
3) High Pressure Fuel Pump
4) Electronic Leads for the Coils
5) Battery Needs Changed
6) Chain Tensioner Failure
7) Coils and Sparks are all Bad, and I am an idiot
I would prefer to do this work myself and can afford the parts. I just didn't want to be fooling around all month without a mode of transportation to get to and from work.
View 12 Replies
I have a 2001 ex. 4x4 6.8 v10. I have been having vacuum issues and brake issues lately. My front brakes seem to be sticking, some times they drag some times the don't squeeze when I step on the brake causing uneven wear and pulling when I stop. Also feels like I have no power assist. I also have a vacuum issue with the auto setting on the hubs, they don't engage I have to manually lock them and sometimes my a/c stays on defrost. And my cruise control doesn't work, the light comes on and love done the self check but it doesn't show anything is wrong. Could I have a bad brake booster?
View 5 Replies
Having problem on mrk 6, sounds almost like a high pitched vacuum leak but I can't find it.
View 11 Replies
4601 DBP, just under 35k on it. At idle, i hear a slight whistling almost like squeaking. I took it to my independent tech and he showed me that if he removed the dipstick for a second while idling, the noise stopped, due to lack of vaccuum, so he believes its in the pcv system. I am still under powertrain and obviously federal emissions 8yr 80,000. Go start your R and listen at idle inside the car for a whistle or squeaking noise that seems like its inside the passenger dash.
View 13 Replies
Bought a 1.8t 04 gli. Was boosting 15 pounds so i did a boost leak test. Found pcv up hose from valve to y pipe at valve cover was almost blown in half, so i replace all of that stuff with oem.
Boost leak test again, found where boost gauge is hooked up to, turbo outlet to n75, the hose was leaking, i fixed that.
Boost leak test yet again, n75 was not clamped down, so clamped that.
Boost leak test one last time, held 10 psi before blowing the cap out of the intake. Which is pretty dangerous, my cap is made out of a spray can cut in half. Sounds like a canon. Anyways i heard zero leaks.
So now I am boosting 18psi and holding perfectly fine. Why I am showing ZERO vacuum on my boost gauge??
View 6 Replies
