I just replaced my injectors in my 12v vr6 and now having some problems. Mainly having issues with start up. Having to feather the gas to get it to start and still runs rough for a min or two.
View 3 RepliesHaving trouble with my '00 Jetta 2.0 A/T w/ 98K miles. Had the water pump replaced @ a year ago (for the 2nd time, the 1st replacement died after <15K miles.) The car has had issues with rough idle when started, especially with a cold engine, since before the 2nd water pump. I've replaced the coil pack, thermostat, and coolant temperature sensor in the recent past in addition to the water pump & timing belt.
The gas mileage sucks, and when it's idling rough it doesn't "idle up", & will stall if the gas pedal is pressed with 30 secs. of starting. Otherwise it seems to run fine. The coolant temp. sensor was replaced after a CEL indicating it was bad. The CEL went off after it was replaced, but it's now throwing a P1296 Cooling System Malfunction. I have noticed the temperature gauge fluctuates instead of staying around the "middle" since the 2nd water pump replacement, and will run "colder" in colder weather. Since spring is here, the temp. gauge stays around "normal", or the middle.
Some research online says thermostat OR coolant temperature sensor. Since the gauge registers normal now, I'm leaning towards a bad temp. sensor...?
Does the hard start/rough idle and the cooling system malfunction CEL could be related?
I have a 2008 MK4 2.0 with only 53,000kms. At 40,000Kms I put new OEM spark plugs.
Just recently, every morning when I start the engine is sputtering and rough running. The engines want to die but I give a little gas, and run rough like it is only firing on two or three cylinders.
When it gets to the normal operating coolant temperature it runs without any problem and I can use the AC. Its only give me this problem on the first start of the day.
Does not have any MIL light on the instrument panel. I scan it with VCDS-Lite and do not found any fault codes. The only thing that's come to my mind is to change the Green Coolant Sensor.
I just got a VR6 Jetta 2001. Everything was fine until I didn't drive the car for like 2 days and it started doing this noise at start up. The noise disappears after a minute or so. What it could be ?
[URL] ....
To start off I have replaced the MAF sensor in this car 3 times now, and have all new oxygen sensors and a new fuel pump. The most recent MAF sensor I have put in the vehichle was 2 months ago and I did it because The car would die while idling, however the mass air flow code did not show up on the cars diagnostic trouble codes. Yet this did solve the problem. The previous MAF sensor had been installed a year ago and failed on me, it was under warrantee. Now that I have installed this newest MAF sensor the car has been running fine until last month.
Since then It runs especially rough at idle and has a tendency to die when sitting for more than a minute in idle. This problem is on and off however, it can run fine one day and as soon as i start it up the next day the problem will reoccur. Now I am getting the DTC for the throttle position sensor, evaporative emission control valve, and throttle position sensor. And more recently, today the problem occurred again, the first time in a week, and now I am getting gray smoke out of the tailpipe. I would like to know if I should again, try to replace the MAF sensor, or if there is some other problem that the Sentra is prone to that I am unaware of.
I recently bought a 4.2L V6 2003 F150 with only 20,350 original miles. This car belonged to an older gent who barely used it, then passed on about 3 years ago, and truck sat around barely used by anyone. When I picked it up I ran some Seafoam through the first two gas tanks as it was occasionally running rough and losing power. Since then truck has been running incredibly smooth, but in the last few days it is getting harder to start. If I pumped it two or three times it would start OK, but today I have had to pump it while cranking it to get it to start. ( the pumping may have nothing to do with it starting)
I am replacing the fuel filter in the next couple of days, as any accumulated junk that was in the tank or lines is now probably in the filter, but it seems that a badly clogged filter would also give me some problems running, and it runs really smooth once it starts. I get a pressure gauge, (I understand the rails have a pressure test port) what pressures should I expect at what moments?
Turn key on :
Crank engine :
I am brand new to the F150 and trucks in general.
I have a 01 7.3 crew cab dually and it's had cold start problems since i got it in 09.I have replaced everything i could think of including glow plugs gpr,harness and batteries. Any temp below 40 i have to plug it in . If i cycle it 3 or 4 times it will start but it smokes and runs ruff. My 00 7.3 excursion starts up down to about 10 degrees than i have to plug it in so i know dually is not right.
I have a afe intake,1.5 injectors, driven diesel rr, adrenilin pump,dp tune by gear head. Kinda at wits end don't mind plugging it in in dead of winter but now one night it's 30 next it's50 and i don't have to . Also have fully built trans by level 10 if it matters .I get battery light coming on every now and again. New alt about every year and a half.
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
the last couple weeks the engine has been running poorly, rough idle .... and sputters until about 4k rpm with a noticeable loss in power. No clue what it is ... it seems to spring up after I got a coolant hose leak on top of the motor.
View 2 Replies01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:
The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.
The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:
Forge 008 diverter valve
034 Motorsports PVC silicone hose kit
Samco boost hose kit
Forge silicone turbo inlet pipe
Eurojet SMIC
custom built 2.5 stainless, catless turbo back
AEM Dryflo short ram intake
GLI MFA cluster
So the Jetta started running rough, then stalled after starting. Couldn't drive it home so I had to tow it. Got to the house and read codes. It gave me P0135, P0171, and P0321. I researched and saw that the only code of these three whose symptoms included stalling was P0321, so I replaced the Crankshaft Position sensor. Tried starting it, and it wouldn't start at all. I kept at it for a while thinking it would catch, but after 5 minutes the battery was too low to crank. I tested the old crankshaft sensor, and had resistance of about 900 ohms, so it was in range. For giggles, I pulled the new one and checked it, also in range. I put one of them back in, and proceeded to scratch my head. Charged the battery up, and now not sure what to do. I need to do a very close hose inspection, but there are no obvious tears or breaks.
View 1 RepliesRegarding my problem (outline below):
>> Went for a refueling stop, and thereafter proceeded onto the highway
>> Approx. 500m into the drive onto the highway the car started jerking and running rough with an initial puff of smoke (none thereafter)
>> Immediately after this initial jerking/shuddering there was a significant increase in fuel consumption i.e. from a familiar 8.2L/100km to 18L/100km in the cruise
>> We continued driving not knowing what it was (I suspected a spark plug may have stopped working)
>> Pulled up at the gas station to observe what went wrong inside the engine bay - no signs of any leaks, fuel sprays, etc. but only that the engine was shaking
>> I checked the rear of the car while the car was idling and observed a pulsating sound...some light smoke and a fuel-rich egg-like smell
>> Asked around and I was led to think the catalytic converter was ruined, so the next day I had the catalytic converter cut out
>> After removing the catalytic converter the problem persisted...although the engine operated with slightly less flow resistance
Attempt at diagnosing the problem
>> My wife called in a technician from BMW at Canal Walk to come have a look and what errors were flagged
>> The tech ran the diagnostic and no fault codes were indicated, except a few short circuit faults due to my incorrectly placing -ve on +ve when I tried to charge my cars battery with jumper cables
>> He proceeded to ask if we changed the spark plugs, I said yes. He then looked at the oil on the intake manifold and said there could be a torn valve on the intake manifold and that air that is not measured by the air mass flow sensor is entering the engine, which is causing the car to rev hunt (this problem of rev hunting has been with us for a while). The engine also shuts down uncommanded at stops and sometimes between shifting gears with the subsequent loss of power steering (very dangerous!!)
>> We also had the O2 sensor replaced a month before this occurence
The images attached (#1- #3) are marked up to indicate the component I am referring to.
[IMG] FilesImage_1.jpg[/IMG]
[IMG] FilesImage_2.jpg[/IMG]
[IMG] FilesImage_3.jpg[/IMG]
Went to Cape City VW in Cape Town and the part number for that orange thing/diaphragm is 06A 198 205A 'Repair kit for valve'. Is this significant? The car sounds as strange at idle...as if has noisy valves. I can upload (if there is an option) a sound clip of how the car sounds if this assists.
I have a Jetta Mk IV, yesterday I went to go drive it and just as I pulled out of the driveway it started running rough, so I pulled back in the driveway and the coolant temperature sensor light came on, then the check engine light. and then it died. Then today I tried starting it, and it will only start and run if I have the gas pedal all the way to the floor, and it runs really rough. Then it will die. I thought maybe the coolant temp sensor since the light came on. I replaced that, and it still does it. I'm leaning towards a head gasket.
View 2 RepliesSo my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
My 2.0 recently had some problems with the coil pack so I replaced it. Now my car hits a "flat spot" when accelerating around 2000 RPM and then another around 2600 RPM. If I am in 3rd gear going about 20MPH and I press the gas about 25-30% it sort of shakes and won't accelerate and when I take my foot off the gas and slowly ease the pedal down it accelerates fine.
My car also runs pretty rough at a cold idle(misfires). When I press the gas it sounds smooth until it gets back to idle. At any temp my car runs really rough with the A/C on. I also hear a rattle/Buzz around my relay panel when the A/C is on. My car is a 1999 2.0 AEG. I don't have VAG-COM just a generic scanner and the last codes I got were:
P0134
P0135
P0141
I replaced both O2 sensors and the beginning of this year and those codes came back right after I did them. I will scan tomorrow and post any new codes.
2001 VW Jetta 1.8t automatic.
Transmission has a hard time going into 1st and reverse. Also some times hits hard going into third. I have a CEL for a vehicle speed sensor? Was wondering if it's not the VSS but maybe one of the other tranny sensors?
Separate question. Same car has a rough idle issue. Occasionally stalls but intermittently runs normal always has a low idle around 600 rpm. I have a code for an injector on cylinder three.
VSS code : P0725 - engine speed sensor circuit malfunction
Injector code : P0203 - injector circuit open cyl 3
I own a 2001 Jetta GLX 12v VR6, lately the car has not been running well. It chokes the power past 3500 rpm's and will continue running poorly and sound sort of like a Subaru boxer engine. Sometimes it corrects itself and runs okay but goes back and forth.
I ran the codes on VAG COM:
6 faults found:
17551 - Load calculation cross check
P1143 - 35 - 10 upper limit exceeded - intermittent
16712 - Knock Sensor 1 (g61)
P0328 - 35 - 10 Signal too high - intermittent
[Code] .....
I ran VAG COM a couple of days before these codes came up and I had a different code dealing with air/fuel mixture, something about fuel running to rich. I'm stumped.
I've noticed more and more recently that I've been having hard rumbling starts and not from the exhaust note either. Its not like I have to hold down the PTS button long either but it just starts hard and turns off pretty rough too and its not even after driving it for long periods. Even driving for 10-15 minutes I have this issue.
View 7 RepliesLast Saturday I got gas on my way home from work then let my car sit all day. Sunday morning i go to start my car and it starts terribly along with a very rough idle. The ride to work was hideous as the car could barely climb a hill (max 25mph and high RPMs 3000 to 4000). Along with bad hill climbing power the car could barely get to 60mph.
I added a bottle of Gumout as I thought I might have gotten bad gas this had no result. While trying to figure out what was wrong I also replaced the air filter.
Fast forward to Tuesday I decide to inspect the fuses in the car and under the hood (all of which looks in good condition). I started the car before i went inside and it seemed the same as it has been all week. Wednesday morning I go to leave and the car refuses to start. It tries to start but immediately quits and then shakes wildly while trying to start. I have since changed the fuel filter, replaced 5 ignition coils, and given it 5 new spark plugs. The car is still doing the exact same thing it was Wednesday morning.
This is a VW Jetta 2005 2.5 Engine
when i start my car up in the morning it whistles pretty loudly for about a minute or two then goes away, also i noticed today when im driving and give it gas in first or second gear about after 3k rpm itll start whistling faintly as well,
2003 1.8t