I recently lowered my mk4 golf with coilovers, now the sway bar is rubbing on the right driveshaft axle... could I just get a small diameter driveshaft instead of getting sway bars? My driveshift is about 2 inches wide...
View 24 RepliesI have a 2004 GLI that I just completed the slave cylinder on, after i got everything back together my driver side axle is now rubbing really bad on the sway bar where it connects to the endlinks. What could be wrong?
View 2 RepliesI got an 2004 gti.... I just dropped it and.. I was having rubbing issues with the sway bar and the axles.. i got adjustable links but its still rubbing.. so my question is.. should i get a new sway bar if so what size? or should i just take it out completely.. or will it not be good if i take it out...
View 6 RepliesI lowered the car on H&R sport Springs with Koni Yellows. On the front right, the sway bar is rubbing the axle under heavy compression (pot hole, sharp dip, bridge joints, etc) and is rubbing the lower control arm (opposite direction) on the driver's side... I got an alignment when I lowered it and it was "within specs"...
I put on adjustable sway bar end links and lengthened the passenger side 1/4" and shortened the drivers side 3/8". left side is slightly better but right side seems almost worse... all rubbing was minimal (barely through the paint on the cast iron parts and nearly no marks on the axle... both strut bearings are new. is it possible that it could be the alignment? Just seems odd to me that the sway bar end links need to be varied lengths to clear....
My MK4 Jetta started leaking coolant recently and I'm not sure where it would be coming from. I already checked the reservoir to see if it was leaking out of there but I could not find any leakage. I've found some coolant on the right side driveshaft near the differential, there is also some on the diff. I'm wondering if this could of happened because it has been sitting on a jack stand not being driven for about 2 months. Is it possible that within that time 1 or more of the coolant hoses could have cracked or anything. And while I'm on the subject of why it's on a jack stand, it also has gone through wheel bearings twice within the last 6 months to a year. Is this normal?
View 8 RepliesI have a intermittent noise from the center of my touareg. It is a squeel or high pitched rubbing sound and seems to be related to load on drive line. I have heard about center driveshaft bearing problems, could this be it.What repairs are available
View 2 RepliesI recently just lowered my gti and I noticed that the sway bar was laying on my passenger side axle. I put adjustable end links on but that did not got the problem either, this car I daily drive.
View 10 RepliesHave a mk4 GTi vr6 with long beaches with sit at an offset of 38. Honestly the offset thing confuses me quite a bit. I'm running 235/17/45 tires. I had my car lowered before the winter and I can only go so low before it starts rubbing. What size spacers i should go with to basically go as low as possible. If not as low as possible, I love a wide rear end so maybe poking in the rear end and lowered in the front for like a rake effect.
View 5 RepliesWhenever I let off the gas there's a rubbing/knocking noise under the car, the sound will slow down as the car slows down but as soon as i press the gas pedal it starts again, it also doesn't do it if I am stopped and in neutral and rev the engine not sure what this could be?
View 24 RepliesHad the common problem of ARB rubbing the drive shaft after I lowered an extra 15mm - It didn't rub before I went this extra 15mm. I got adjustable drop links on and they also didn't work. I basically told the garage to sort it out and they put standard drop links back on (not genuine) and also new wishbones because I needed them. Got my car back and the rubbing was even worse. So I raised it back up the 15mm, to where it was before the rubbing started, yet it's still rubbing like crazy. I'm wondering if the new wishbones may be causing this because of new bushings or something and it all being tighter. And also what am I supposed to do? I shouldn't have to buy a whiteline ARB because it wasn't rubbing at this ride height before the wishbones and drop links were changed.
To summarize:
>Lowered car extra 15mm, rubbing started
>Drop links and wishbones changed, rubbing is worse
>Raised back to the point where rubbing started and still rubbing just as badly.
I've got an 03 Jetta TDI 5-speed with 210k. I just replaced tie rod ends, ball joints, struts, shocks, springs, and bushings/bearings on the front.
After I took the car off the jack stands, I tried to reverse and the car is held in place pretty firmly. I gave it a bit of gas and it sounded like the brakes were rubbing. The brakes feel a little soft.
I checked the wheel clearance (I didn't lower the car) and everything looks fine. Did I pinch a brake line or something?
While switching freeways yesterday and shifting down into 3rd before hitting the exit ramp I heard I a slight clunk, and then this continual noise began. I initially wasn't quite sure if it was my car or the sound of the of the large semi engine braking in front of me so I continued on to the freeway and was able to shift back up to 5th and get to speed.
However, I held back to around 60Mph because the noise started to worry me as I continued to hear it after passing the 18 wheeler semi. I got off at the next exit and noticed that the noise ONLY occurs when the car is decelerating. It happens in every gear as well as neutral; having the clutch in or out doesn't make a difference either.
*When accelerating in any gear, even the slightest bit, the noise disappears.
I've scavenged the forums to find a similar issue but to no avail.
I've uploaded a video that shows the issue occurring. The video is taken from the driver's side wheel, but the sound resonates throughout the front of the car, can't really pinpoint where though.
2002 Jetta 1.8t possible transmission noise
[URL] ....
2002 Jetta 1.8t ... 210k Miles
I've recently replaced the Control arms, outer tie rod ends, ball joints, springs, struts, all for rotors/pads, rear calipers, handbrake cables, timing belt (with pulley kit) water pump, etc. full syn Oil changes every 3k-3.5k miles, Premium petrol only.
So I've had a low rubbing sound specifically when I'm turning or banking right. I don't want to put much more money into this mk4 because I'm planning on getting a new car in the next 12 months. How do I know which bearing needs replacing?
View 2 RepliesMy front left tire is rubbing to the point where I can feel it in the steering wheel slightly slowing the car down. This happens only going over about 40-50 and only when i turn the steering wheel like an inch to the left. To better clarify it doesn't rub while turning left going down a slope.
View 2 RepliesI have the most terrible clunking/rubbing sound on my right passenger side, especially when I'm turning left. When I drive straight it sounds like the wheel is hopping even when going over minuscule imperfections in the road. I also get a terrible rub when going over speed bumps or into grooves and dips in the road.
I've searched and searched but cannot come up with a answer towards rectifying the issue. My car hasn't been lowered; I'm running the stop 337 suspension. I've replaced the following within the past two years:
-control arm bushings
-ball joints
-tie rod ends
-upper strut bushings and bearings
-passenger side axle
-dog bone mount
-engine mount
-tranny mount
Most recently:
-front struts
-sway bar end-links
-driver's side axle
It seems to like everything should be solid considering I've done all of this crap. I don't understand why I'm having this issue and why it sounds like it is getting worse and worse.
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 RepliesMy mechanic says I need to replace both front sway bar links on my 2002 Jetta....I am, of course, hesitant to do it at this price. How critical is it to replace? Can I get junk yard sway bars to make it cheaper? And can I do it myself (have no experience fixing anything....
View 11 RepliesCame home in the R32 tonight to an awful noise.. Pulled the drivers rear wheel off and pulled a small rock out from between the rotor and dust cap however in doing so, discovered a huge crack in the driveshaft! This is about 2" long... How critical is this to be repaired and is it covered under warranty at 75k mi???
View 6 Replies2013 GOLF R 9800 MILE, Driveshaft went out. The dealer is going to take care of this problem. I don't think i should be having to replace the drive shaft at 9800 MILES.
View 21 RepliesHow to keep the driveshaft from spinning while I undo the 10mm 12pts? It just seems around enough to slightly scare me into thinking the car might move, and I can't seem to break them loose.
View 10 RepliesNot driving the R as much now that I got a 2011 Triumph Street Triple R. I use as my primary transportation. But I had the car into the dealer this week for service and they said there is a rubber dampener on the driveshaft that is starting to crack and get loose.
I didn't get time to check out the car on the lift and have not had any problems with this shop in the past nor the mechanic who has ONLY worked on my car since new. The R now has 104K on it.