Golf IV / Jetta IV :: Stalls Out In Stop And Go Traffic / Bang And Clutch Pedal Drops To The Floor
Aug 14, 2016
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 Replies
Advertisement
2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 Replies
So this has happened a few times pedal drops with no back pressure then give a bit pull it back up by hand and it's fine has happened 4 or so times in the last year. I'm reluctant to replace slave and master cylinders could it be anything else? 87 Ford F-150 hydraulic clutch
View 10 Replies
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 Replies
So last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
View 3 Replies
I just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 Replies
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 Replies
So my clutch has been acting up lately. When it sits for a few hours the clutch engagement point seemed to creep down but over the course of 35 minutes of driving would work its way back up again. Today it was unusually low and wouldn't let me get it into gear. I tried pumping it a few times and realized it wasn't coming back up all the way, I pulled it up and then tried again and it just dropped right to the floor where it now sits. Fortunately I was at work and can hang here until my ride arrives, and will just wait until late tomorrow night to drive it to my shop without stopping...
My guess is I need a new clutch master cylinder. I have plenty of fluid in there although its a bit old so I'll be changing that when I change the cylinder. Could it be the slave cylinder? If so is it a bear to change that? (do I need to drop the trans?)
View 16 Replies
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
View 16 Replies
I have an '01 gti glx that I just swapped a motor into. I got the motor out of an '01 jetta glx, exact match AFP engine code.
I get cylinder 2 misfires mostly (high number) but I also get 5 and 6 intermittently as well as a P0300 code.
Sometimes I also need to hold the gas down just to get it to start even after the crank sensor.
The engine idles sometimes at 600 rpm but drops and nearly stalls after revving at all.
What I've tried so far:
working cam sensor from my old vr
brand new crank sensor
brand ned wires/plugs
new fuel filter
swapped injectors of misfiring cylinders from old motor
lined up the timing 3 times now and its still perfect
I know the coil pack works because it was on my old motor, which ran fine, just leaked oil.
View 2 Replies
I was driving, Iput the brakes on then suddenly I heard a loud bang and brake pedal went all the way to the floor. I knew there was something wrong with the brakes, parked went and checked the passenger side rear brake caliper was ripped off which made a hole through my rim and also ripped off the brake lines. I need to get the part but I don't know what its called. See the pictures....
View 12 Replies
Installed a new OEM CV axle on my 05 GTI the other day because I had been having a lot of issues with off brands and then today (I'm a delivery driver) on a run I was turning into traffic from a stop and I heard a clunk and then no power. The engine was still running flawlessly, but no power driver to the wheels.
I'm not going to be able to get a good picture until we get there but I'll upload pics when I get them. The bracket looked completely f'd. I could only find two of the 6 bolts that hold the CV axle in place and one was snapped in half.
View 24 Replies
I have a 2001 jetta with a Vr6 the clutch petal just goes to the floor. No return. What's could be wrong?
View 2 Replies
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
View 2 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
My husband I purchased a 2012 Subaru Outback May 2012, we notice a hesitation when we first drove it and couple weeks later it started stalling out, now it stalls about every other day, we have noticed that ours is after a 15 to 20 minute stop and go traffic and then when your able to drive at normal speeds without stopping, and then stop it stalls out, we have rough idle and transmission acts like it is trying to shift but I know this isnt possible with a CVT transmission.
View 5 Replies
I've done a bit of research both here and on other sites. I originally thought that I had a bad flywheel but I'm not convinced. First I'll give a little backstory. I just installed steel shift forks because one broke and got jammed in the gears. None of the gears are damaged and I assumed that when it slammed to halt, the flywheel got messed up. So anyways, the complaint is that when the clutch pedal is released I start to hear a knocking sound which becomes more rapid with RPM. When the pedal is depressed the sound goes away. This sound seems to be coming more from the driver's end of the trans. The car still moves in all gears so I can't imagine that I put it together wrong.
View 6 Replies
03 Jetta. The cruise has not been working. Turning cruise on and off works fine as light comes on on dash. Brake pedal switch was replace about a year ago, and I don't think that is the problem because when this was the car would actually go into limp mode.
Just checked the clutch pedal switch by jumping the plug (This was the blue switch lower on the pedal), and still no cruise function. I'm really leaning toward it being the "set" switch/button on the steering wheel as this just feels kinda broken. Did I test the clutch pedal switch correctly? Any other reason the cruise would stop working?
View 9 Replies
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 Replies
Today I parked my golf on the street and it was raining, when I came back to the car after four hours the street had flooded and water was about an inch below the bottom of the door on the driver side, and about an inch (or more) on the passenger side and up to the bottom of the exhaust pipes in the back.
The car started fine, but when I began to drive it the clutch would slip and then bang while engaging. Once I had taken off a few times gently everything smoothed out. Car drives fine and the engine bay was dry when I got home (a 40 minute highway drive). NO water got inside the car at all, so the interior was completely dry, every thing appeared to function perfectly. My question is, assuming just the bottom of the motor, trans, and undercarriage got wet is there anything I should be weary of? Any sensors or electrical things down there? Lights, ac, door locks, everything is working and running fine and dry at this point.
View 3 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
