Golf IV / Jetta IV :: Shifter Got Stuck And Won't Budge Out Of 5th Gear?
Apr 29, 2014
I'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
View 3 Replies
Advertisement
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
View 2 Replies
I drive a 2007 Ford Focus (manual trans), and it's been acting funny lately.
Here's the problem: Lately, when I start the car and try to put it into gear (either 1st OR R,) the shifter won't budge. While the engine is off, I can put it in gear just fine. After I wait for a little, turn the car off and on again, etc, I can get the shifter into gear if I really push it HARD. (I know I probably shouldn't do this, but... I was terribly late and desperate!) Okay, so I get the car into first and manage to pull out of my parking spot without having to reverse. When I go to get into second gear, I've still gotta push the shifter REALLY hard (again, bad!! I know!) but maybe a little easier. Where I live, it's stop-sign city, so I have to stop and go a lot, and within a few minutes of this (maybe 3 or 4 cycles of N, 1, 2, maybe 3, N) I can shift smoothly again and the car feels totally normal.
The strange thing is, this happens sporadically, and I can't seem to see any external factors that correlate with the problem, except that it seems to be worse when the car's been sitting for a couple days. Sometimes the car shifts just fine, and sometimes it won't get into gear at all. In general, the car's in pretty good shape: no accidents, scheduled maintenance, etc. I guess the only caveat is that a couple years ago, TWO people learned to drive stick in this vehicle, so maybe the transmission has taken some abuse.
View 5 Replies
2000 VR6 automatic. Yesterday my car was stuck in park couldn't move the shifter . Figured it was the brake sensor switch when the brake is engaged food pedal lights do not go out, I replaced it this morning but still won't work I've been driving it around in limp mode?
View 4 Replies
The issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 Replies
So I have a 2010 jetta 2.5 and my key is stuck in the ignition has been for a couple weeks also don't know if it's related but when I start the car I can pull the shifter out of park without pressing shifter button just have to press brake and after I shut the car off if I take it out of park and put it in gear it just freely rolls only stops if it's in park. NOT A DSG
View 3 Replies
I have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
View 18 Replies
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
View 10 Replies
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 Replies
My03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.
View 7 Replies
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
View 5 Replies
I have a 2000 Golf GLS which I tried to replace the shifter solenoids on and since I replaced them it shifts very very incorrectly it almost feels as if it starts in 4th gear and works its way to 1st.
View 2 Replies
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
View 5 Replies
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
View 1 Replies
I have an 89 Ranger, 5 speed, 2wd, M50D transmission. On the way home tonight I was upshifting from a stop and when I went to go from 4th to 5th the shifter wouldn't budge. Luckily I was on a back road so I pulled off the road and tried all sorts of things (rolling truck while stopped, etc) and the shifter just will not budge.
Now here is the thing. I had my fiancé with me and no tools so I really couldn't do any diagnosing. However, 6 months ago I replaced the clutch, pressure plate, throwout bearing, slave cylinder, and pilot bearing. While I had the transmission out of the truck I changed the fluid, siliconed around the rubber plugs, and put a shift bushing kit in. The bushing kit is the bushings around the shift ball with new wave washers and new pins that insert into the ball.
It is obviously not related to the clutch as it engages/disengages properly. When this happened, there were no noises of any kind when I shifted from 3rd to 4th. It just will not come out of 4th. I am going to pull the shifter out tomorrow and have a look. Do you think one of the new pins that I drove in to hold the shift ball broke or fell out or something and if so would it cause this problem?
View 4 Replies
Damn car is stuck in 3rd gear! Hooked up scanner and the screen just says error! I have to keep the scanner in the vehicle, hooked up, just to drive the car. That's just so it'll shift as its supposed to! Now it's not letting me pull the code out, in order for me to erase it! It just keeps saying "error".
View 1 Replies
I've had my 03 VR6 6-speed for 12 years. It's been a second car for the last 5 or so, but regularly used. Friday morning the car got stuck in 3rd gear. The stick will only move from neutral position and down towards 4th gear. I've inspected the short shifter under the hood and the bushings under the shift boot. I did not find anything that diesel geek (the short shifter company) had me check for.
I brought the car into a local shop I have never used before (my usual shop closed), and today they called me saying its a transmission issue. I have not given them permission to open anything up. I am going to take the car home for now.
I have had to repair a broken 1-2 gear fork before. And at that time I had the 3-4 gear for replaced as well.
I should also mention, I similar issues on a quick drive i took the car on the night before. I thought it was just me acclimating to the shifter/lower power of the car as I hadn't driven it for a while. The point is, it drove fine afterwards and it drove fine for a 40 minute city drive to work the next morning.
View 5 Replies
I just picked up another GTi and knew the transmission was iffy when I bought it. I had to deal with the serpentine belt tensioner which is now new and also a new waterpump since it was wobbling.
I've already drained and replaced whatever oil was in there with VW G60 Gear Oil which is what my Dealer here told me to put in and it shifts smoother now but still has the same issue. I also did the Shifter Cable adjustment to see if that was the problem but that only made it easier to shift but it still got stuck.
Basically what happens is when driving I shift into 3rd gear and when I go to shift out of 3rd it comes out of gear but it's like it hits a brick wall and will not go into the home position. I was hoping the adjustment and new oil would work but it hasn't done anything.
View 2 Replies
I have a 2002 Camry with (440K Kms) and automatic transmission. I am the second owner and had this car since 130K Kms so I have been driving it for a while. The car was in great condition but recently, the transmission started to give some trouble where it's gear changes were not smooth. Also, when I would come to a complete stop, trany would go into neutral even though I have not touched the gear shifter and it is still in drive.
I had my mechanic drain and fill transmission fluid since it was a bit dirty. A few days later, the car would park with gear box in "P" but no matter which gear I would put the gear shifter into, it would remain in neutral and won't pick up into any gear at all. So, I parked the car on the driveway. Couple of days later I wanted to try to see what the issue was and now, no matter what gear I put the gear shifter into, it stays into park.
View 14 Replies
Just got my 2013 Elantra Limited last weekend. It appears the car is having some issues with the transmission shifter. I am not sure if its tranny related, but I highly suspect it is. Dealer gave me the usual bs not being able to duplicate the symptoms.
1. Intermittently, gear selector would get stuck in neutral, when I try to put the car into P, after a long or a short drive.
2. I would have to wiggle the shifter to get into P, or I would have to shift to D, and then I am able to shift back into P.
View 22 Replies
I have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 Replies
