I replaced the knock sensor because I was getting the p0327 for the front knock sensor. Drove it again and still sputtering and CEL came back. What are other causes of this? N75 solenoid? Low fuel pressure?? It has a spectre air filter kit on it. Didn't know if this would do it. I cleaned maf. Just put new plugs in it too.
View 5 RepliesI recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesI got my car in November and I just did a scan and got this code. I don't have a CEL on. I do feel a slight vibration from time to time. It's very light.
Should I clear all DTCs and then run a scan a couple of days later to see what codes I truly have? Or should I address this code?
If yes, what should I do about this code? Do I need to buy a new knock sensor or should I check the wiring first with a voltmeter?
Monday get CEL with codes p0722 and p0322. Car is in limp mode during these codes. Yesterday I change g68 sensor. Cleared codes, rough start but was sitting most of the week. Drove around fine, no limp mode, shifted fine. Started up a few times immediately after. Hours go by I go to leave and it won't turn over though it sounds its wants to. No clue why this is happening or what changing the sensor could have done. This is a 01 GLS 2.0 auto. Not sure where to from here especially since it drove so well afterwards.
View 4 RepliesKeep getting o2 fault codes. Replaced sensors came back. tried another set of sensors came back. Checked wiring for breaks no luck. Replaced ecu still no luck. So going through wiring again and checking for continuity. Looking for a list of what pins to check for voltages, and what each should be from ecu to sensor connectors. Looking for what wire is signal and how to and what voltages to check for...
View 5 RepliesHad to replace my primary O2 sensor recently. I got the sensor straight from VW and it comes with all sorts of clips and whatnot. Looking for a picture of how the wiring is supposed to be routed and what I'm supposed to do with all of the plastic clip pieces?
View 2 RepliesI started my car the other day and found that it only drives the first gear and I can also put it in reverse. VCDS gave me a 00281 code saying no signal from Vehicle Speed Sensor G68. I replaced the sensor, but it still doesn't go into gear beyond 1st.
VCDS gives me the following codes after replacing G68.
2 Faults Found:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
00281 - Vehicle Speed Sensor (G68)
03-00 - No Signal
I came across TSB 01-99-02 which says something about the codes being incorrect. It seemed a little vague about whether it is actually G38 or G22. I don't want to buy more sensors only to have it be something else. The speedometer and tach work fine so G22 doesn't seem likely to me.
The VCDS site says it could be several things including bad G68 or G38 sensor, low fluid & bad valve body. Was it the G38 sensor?
I have a 2006 VW Jetta with 92K miles and just a couple of days ago my check engine late came on and when i took to an auto store to check the code, it came as P0332, Knock sensor 2 in bank 2 is faulty. Three things have happened all around the same time and I am not sure if they are related and are just coincidence.1.Check engine light came on.2. I have noticed after that, my car RPM has dropped, idles at about 600-700RPM and when trying to accelerate, it tops at 3000 RPM and feels like the motor cuts off at that point and I have to step off the gas and the car runs ok again, but cant go over 3000.
Had trouble getting on the interstate due to this and thought the car was going to stall, but it didn't. just had to back off the gas and let it run, It did go up to the speed that I wanted, but seems like it wont go past the 3000 RPM point.3. My fuel gauge, drops to empty when it reaches the half way mark on the meter. It stays at the correct level when I start and keep the car in idle, but when I start moving, it drops to empty. When I fill up the tank, it goes all the way to F, and after the car goes the usually of about 190-210 miles, when It reaches the half full level, the meter drops to zero, so have been using my trip odometer to drive after that.
I was cruising at around 80 mph and the epc and check engine light flashed for a second, and I felt a slight loss of power for a second then it was normal after that. When I pulled over and check out the engine, it was making this noise (video) when I got home, I scanned it with my vagcom and got P0333 knock sensor signal too high, maf sensor signal low, and a clutch pedal switch I've replaced the bushings on the intake rod with the gruven bushings and the sound is still there.
View 11 Replies I recently bought a 2001 Golf 1.8t and everything was running smoothly until a few days ago.
I had to change the timing belt because I have 80,000 miles on my car, and the day I was going to my mechanic, I scanned the codes, and the p0301 and p0303 codes came up. The two codes are cylinder one misfire and the cylinder three misfire. So, I switched the two bad coils with the supposedly good coils to see if the codes changed, and when I scanned it again, the bank 2 lean 1 code came up. I had my mechanic look at the spark plugs and when we checked the plugs, there was oil ABOVE the plug, leading us to believe the misfire was from oil leaking in because of bad spark plug tube seals/valve cover gasket.
Regardless, I bought four new factory coils and four new factory spark plugs and factory valve cover gasket and spark plug tube seals. I replaced them today and I was hoping, in a perfect world, my misfire would stop and my car would stop sputtering and revving and fluttering my RPM's. I was wrong. The only other thing under the hood that I can think would have anything to do with it is that the PCV hose is just about fully ripped, but I'm not sure If that would still make my car sputter and cause my car to misfire.
I bought a 2000 jetta gls vr6 5-speed. Only had the car about 4 weeks, already I am in, ball joints, struts, brakes, core leaks and my half shaft fell off at the transmission. Now, driveabilty issue.
Severe loss of power, sputtering bad. when i shift, the car revs a bit. installed new O2 sensor due to a rich code and a out of range code. Now the EPC light is on with an implausible brake switch signal. Replaced switch still comes back on. Still running like poop. Changed the plugs also about 1k back. I just ordered a MAF.
I have this issue from time to time where I will be driving and my car will randomly stall itself out and shut off. what could be the issue?
2nd I have an issue while idling, where if I am idling I feel a slight vibration like it is about to stall.
3rdly How big of an offset can i have on rear wheels that are 18x8?
The aforementioned questions are regarding a 2004 GLI.
I have a 2003 Golf VR6. Last weekend the car started sputtering and then died. I haven't been able to get it restarted since. I have already replaced the fuel pump relay and the fuel pump. Since I replaced the fuel pump it will prime when I open the door or when I insert the key. When I go to start it it will only stay running for 5-10 seconds then acts like its running out of fuel and dies. EVERY. SINGLE. TIME.
Its not throwing any codes other than a couple 02 sensor codes telling me its running lean. What to do at this point. I was told that vws have a secondary fuel pump relay under the passenger rear seat that sometimes when it goes bad it will turn on the fuel pump to prime it, but wont kick on when its supposed to stay on. I cant find anything on the interweb about it. The shop I took it to that diagnosed the fuel pump said it wasn't throwing any codes when they scanned it.
I have a Golf 1.8 t 2003 and when the car reaches 4000 rpm on 3rd gear it starts sputtering and can't go above that rpm. it sputters a bit on 2nd gear but at about 5000 rpm but it keeps accelerating. I couldn't try the other gears because i don't have a suitable to reach those speeds (traffic laws speed limits). I have noticed a slight tear on the connection between the hose from the air filter and the T hose. could that be the problem.
View 9 RepliesMy 2002 VW Jetta 1.8t has recently taken a dump and had been sputtering jumping periodically when I pressed the accelerator. It had started several months ago and has become progressively worse until it didn't start anymore. Usually I could turn it off and then turn it on again and it would be fine. Not anymore.
I checked it out, the fuel pump, engine speed sensor and fuel pump relay had all been shot so my initial thought was to check for a broken wire somewhere if it had been shorting. All wires are intact but i can't find the ground connector for the fuel pump. Where is it located? I have checked and serviced all other grounds, have replaced fuel pump, relay and speed sensor. The injectors are getting juice but aren't working (the injectors themselves are still good)
Also, there are three connectors behind the relay bar underneath the dash where the fuel pump relay is located. What order they are supposed to be? There is blue, red and green. They were disconnected (not my idea) and now I don't know how they go back.
I have a 2000 VR6 M6. I will do my best to describe the problem I am having and what I have done so far.
I get a knock when going in to 1st, 2nd or reverse. If I let the clutch out real easy I will not get it. If I go in to 1st depress the clutch and then move forward again it is not there. Same with reverse, go in to reverse and I get it but depress the clutch and then let it out it does not happen. When going from 1st to second during normal diving I will get it, and leaving from second I get it also.
What I have done and looked at so far, replaced the left side mount and the dog bone. Inspected all other items such as the control arms, body mounts and stabilizer bar. I have also changed the fluid with Synthetic 75w90. Axles look pretty good and I do not suspect it is there.
2003 Jetta 1.8T. My car has an issue when you're driving and want to take off. I try to step on it and the car gets stuck. There isn't a CEL and one doesn't flash while it happens. The turbo attempts to spool and then gets stuck almost like sputtering and then misfires. "Sputtering" can last anywhere from a second to until you let off the gas. If you slowly climb through the revs it doesn't do it but if you punch it you're guaranteed to get stuck. I don't have a boost gauge to see if it's spiking but I'm running out of money, time, and options. I've had my car at my normal shop and they can't figure it out and the dealer techs are stumped too. Oil was changed last month and I did a seafoam treatment before I changed the oil.
Mods:
- CAI
- Unitronic Stage 2
- 225 TT DV
- Techtonics 2.5" DP with high flow cat followed by 2.5" straight pipe
- ST Coilovers Maxed out
- Corvette Sawblades 17x9.5 square with 38mm and 33mm adapters. Front and rear tires are different tread, and size. Fronts are all season 205/40/17 and rears are a summer 215/45/17
- Fresh wheel bearings and custom Porsche 930 Chromoly axles
Things that we've tried:
- New MAF
- Flashing back to stock and reinstalling the file as welling as trying lesser flashes (stage 1, 1+)
- New plugs
- New coil packs
- New throttle body
- Boost leak test (no leaks)
- Front o2 sensor
- New crank position sensor
- Throttle body position sensor
- New N75 valve
On my way to work, my check engine light started blinking and car was sputtering (real bad on idle). I ran the code and it came back with misfires codes. I changed the coils/plugs, fuel filter and fuel pump last year. Can the coils be bad already? When I clear the codes the car will run fine for a little while. But after a couple miles CEL will blink and the car will run roughly again.
Car : 2004 Golf 2.0
Codes:
16684: random multiple misfires
16648: fuel injector #2 short to ground
Ok...so I drove my car last night about 120 miles and all was well. Got up this morning to go run some errands and the car started acting weird, sputtering. The check engine light was blinking on and off, then it came on solid and stayed on. I haven't checked the code yet.
2004 Jetta GLI1.8 T Manual Transmission
My Jetta wagon with 131K on it has a ping when I accelerate hard. I know it's not bad gas, but probably a carbon buildup. I've done a few seafoams that had some effect, but not much. I'm gonna do the water spray/steam next. Which components are prone to carbon buildup in these gassers that would cause ping?
View 4 RepliesI can't figure if it's a TB issue as I've just had it replaced or a mount problem. I only get the knock on biting point idle and pull away under load. This noise is driving me insane.
View 2 Replies