I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 RepliesRecently I've noticed that every time when shifting from park to drive and occasionally from reverse to drive in my 05 Golf GLS, I would have to remain off the gas for 3-4 seconds otherwise the car would jerk forward. If I press on the gas ever so slightly, the rpm would go up to around 1000 then jerk. Why this is happening?
View 2 RepliesI bought a MK4 GLS 2.0 5 spd with 200,000km on it back in february, It currently has 208,000km on it.
Whenever I drive in reverse, I get this loud shuddering/rattling noise with a slight vibration. I've noticed that it is louder from a stop and when the clutch it partially depressed accelerating,but pretty much goes away when the clutch is let out or when coasting.
It is sounds like it is coming from behind the front seats to the rear of the car. It almost sounds like the rear shock mounts are rattling. I also sometimes still here a slight knock, similar to the sound of worn sway bar bushings, but replaced those a few weeks ago.
I also get the same knock whenever I screw up a shift and the engine moves. I also considered and engine or transmission mount but i don't really get any vibration through the steering wheel other than a small amount which could be attributed to the poly dog bone bushings.
About two months ago but I replaced the RR shock mount with a new one. The old one looked fine. I replaced the RL shock mount with the one that I removed from the RR side.
Changing the shock mounts made no difference but I noticed that I could easily compress the RL rear shock with my hand. Could worn rear shocks be causing this noise/vibration? I've searched but I can't find an explanation besides the shock mounts.
I have replaced a few suspension components in the last few months:
-rear beam bushings in august
-front sway bar bushings a few weeks ago
-RR rear shock mount (new)
-RL rear shock mount (used from other side, but looked fine and replacing it made no difference)
-energy suspension poly dog bone bushings about six months ago
I don't think the car was really maintained that well due to it having original sway bar bushings and having tires that were worn very unevenly due to the rear beam bushings when I got it.
New to the jetta (used to own Saabs so not new to issues) OK, 2003 jetta 2.0 CEL is on for the CAM Post sensor. Car is in limp mode. has been for a while before I touched the car. I have replaced the Cam post sensor, I replaced the Crank Post sensor, replaced the coil pack, replaced the water pump and the timing belt. I have searched a lot of the other threads before posting this one. Triple checked the timing (3 people did not just me) I replace all the other stuff because I had codes the water pump and the timing belt just because they were due. i had one last code P0343 so when i replaced the WP and the TB i replaced the sensor. Still in limp mode, still have the code i pulled the plug on the Cam post sensor. then i said to my self this car should NOT start. but it did start and i drove it around a little, shut it down and car started up again so I am at a complete loss.
View 8 RepliesMy 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 RepliesI replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 RepliesWhen I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 RepliesI been working on this unit and I running into this
no foward
no reverse
no foward in and gear at all
I have to check pump pressure
I'm changing fluid and filter
1994 F53 460 CID will not move in drive or reverse - iRV2 Forums
I have a 2001 vr6 Jetta automatic transmission. When I shift my car from park into to reverse or drive the whole car jerks as if it's banging into gears. But while driving it drives normal. When I stop and accelerate I feel the same jerking you would say.
View 5 RepliesI have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 RepliesI had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 Replies'05 Accent, 19k miles. Car has been great, except suddenly I'm getting a weird shifting issue when I first start the vehicle. After I put the car in reverse, then change into drive, the car SLAMS and stops briefly, as if I've hit something. This has started to happen a lot lately.
View 1 RepliesWent and changed my fuel filters today... Primed the truck 6 times. Started it. Ran great, then got a low fuel pressure and reduced power notification. Turned it off. tried priming it 10 more times, no start, tried 15 more times. No start. Took off the outlet on the secondary filter, solid flow. Took off the return on the L/H fuel rail, pinched the line and put a hose on the rail... Once again solid flow. I can hear air somewhere under the hood but I don't know where... Driving the 7.3 to work tomorrow but this is driving me up the wall.
View 14 RepliesI'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesI got a 99' Jetta gls 5 spd. I just replaced the transmission and now the car won't engage reverse from inside the cockpit. Reverse can be engage from inside the engine bay, but when the shift knob is depressed nothing happens. Linkag cables are in the correct spots.
View 6 RepliesI have a 2003 Jetta Gli with a VR6 manual transmission 6 speed. So the other night I am pulling into this store parking lot and all of a sudden my car is just rolling its still in gear and running but when i push on the gas it just revs the motor i thought i was in neutral for a second but I wasn't so I jump out and push it into a parking spot.
Car is running but when i put it into gear and let off the clutch it just revs. so i have i towed to my house it was late so i decided to look in the morning.
So I go out the next day its still the same only now when i let off the clutch it just dies. I'm not an auto mechanic expert by any means any car work i have done is just self taught as needed diving in and figuring it out myself.
I did do the Cv axle on the passenger side last year i bought the one from O' Reilly auto parts. I know its the cheap one and probably a no no. Could this be my cv axle? Did my clutch go out? It moves through all the gears except reverse when the clutch is depressed. Could it be my transmission?