Golf IV / Jetta IV :: Key Won't Turn After Ignition Switch Replacement
Nov 19, 2014
I am having a little issue with the ignition in my car. I had the typical no headlights/wipers/heater etc. so I ordered up a new ignition switch and when I went to replace it, the switch fit perfectly and had the correct part number but when I put my key in to try and start the car I couldn't even turn the key but when I put the old switch back in it would turn just fine. Also when I removed the old switch I noticed the red wire going to the switch was slightly burnt right at the terminal.
Here is the basic procedure I did:
-Unhook negative battery cable
-remove lower dash/ center console
-remove switch
-install new switch
Whats this little metal piece? I did not see that when I did mine...
View 10 Replies
Advertisement
Just got this car it's 2001 gti turbo. The guy said that the key fob was back. But I changed the starter and still no luck. It had all new plugs and I went to check for spark and there was no spark or fuel. So then I got a new crankshaft sensor and still no luck. I haven't gotten the chance to check for spark yet. And now those lights and beeping keep happening even without the key In the ignition. Can it be the ignition switch or something worse?
View 1 Replies
Is it possible to change the ignition switch without the key. Problem is my old key broke so im replacing the whole switch.
View 1 Replies
2003 Jetta, has a bad clutch so has been sitting for about 6 months. Unfortunately, it is not the most water tight car, so it is a little humid/damp inside. Here's the issue, put the key in, try to turn it, won't budge. Shot some lock ease in, still no turn. What to try next?
View 5 Replies
Having a few electrical issues lately, that are really starting to irritate me. This is pretty random. OCCASIONALLY, not all the time. When I turn my euro switch all the way to the right, my windshield wipers will go across the windshield twice. Obviously the wipers aren't on. And I don't accidentally hit the stalk. This just random and annoying when it smears stuff across the windshield. I don't even know where to start.
View 2 Replies
So noticed my cruise control does not work when I turn switch to on position the green light in cluster does not come on what are some problems that I could look into and also any example of using turn signal Bulbs in the head lights as drl lights instead of it running off of the actually headlight bulb?
View 9 Replies
I just had the ignition switch replaced on my 2001 Toyota Sequioa. Now my blinkers work but will not shut off after I complete the turn. Additionally, the blinker "stick" is very hard to move in either direction. I plan to take my car back to the dealer and politely request this blinker repair be warranty work.
View 1 Replies
I have a 97 grand prix GTP that I am replacing the ignition switch on. I am having trouble locating the small hole on the key cylinder that I put an allen wrench into to release the key cylinder.
View 2 Replies
I have a 1997 F150 that I have taken to a mechanic twice and it is still not right. I had a igination switch replaced and now when the humidity is really high
(I am Guessing), I can have the key in the house and my truck lights flash the radio is on and it sounds like it is trying to start. How hard is it to replace the igination switch myself. I believe it has a short someone in the steering column.
View 1 Replies
Had to replace the ignition switch. after I went to crank it after switching it out, there was a buzzing around the relay control module. Thought that maybe somehow the ignition tripped something in it so bought a new one. IT is still buzzing and car won't turn over. everything lights up on dash. tried to see if there were any codes and the scanner just reads "fail".
View 5 Replies
I was having all the tell tale signs of the almighty ignition switch. No lights, wipers, heater fan. But I didn't have time to change it. The other day went to start it and nothing. I changed the switch I have headlights wipers blower fan now which is sweet. But the car still wont turn over.
View 2 Replies
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 Replies
I put my LS 430 key in my RX330 yesterday, I realized as soon as the ignition would not turn. I put the RX key in, and ignition will not turn. I'm assuming that the pins may be locked so I tried a few options.
- I wiggled the key.
- I lubricated the lock.
- I tried rocking the car while trying to turn the ignition.
- I tapped the ignition lightly with a screw driver and hammer, but no luck.
- I turn the steering wheel while turning ignition to make sure its not locked.
I really don't want to get the car towed to the stealer/dealer.
View 8 Replies
I have a problem with turning my key. It will not turn at all. I have taken the upper and lower part of the cover off to expose the switch and removed one screw from the ignition housing, but the internal part of the ignition switch will not come out. How do I completely remove this ignition switch. I have already removed the negative battery cable. It seems this is a continual problem with focuses. Oh, do I need a releasing tool to release the ignition switch.
View 7 Replies
I have a 2000 Staturn LW2 auto, 6cyl. When I try to turn on the car, sometimes the engine does not turn, doesn't make a sound, nothing. When I move the steering wheel, it turns on fine, it has to be in a certain position. Does that mean, the ignition switch is faulty or is it the pin? Is there a test I can do?
View 7 Replies
I'm having a problem with my ignition switch. It won't turn and I have to turn the steering wheel for it to finally work.
View 4 Replies
I have recently been having problems getting the ignition switch to turn. There seems to be a negative correlation to warmer weather (the warmer the weather, the more likely I will have a negative experience --- and I will get the switch to turn only with some difficulty). When I have such a failure (in which the switch does not turn), I take the key out, wipe it off with my hand, flip it over and shove it back in. Sometimes this works with one try. Sometimes it takes multiple tries. My fear, of course, is that one of these times it will never work, and I will be stranded. I should add that I do have another key, and that I have had the same experience with this key. I don't really want to spend hundreds of dollars on a new ignition switch... and I especially don't if that is really not the problem.
View 2 Replies
97 Toyota Camry 2.2l motor.
Sometimes, when I turn the ignition on I don't hear a sound and all the power dies in the car (the radio ejects the CD and all the presets are erased when I turn it out of start). This can happen once or twice in a row then generally the car starts up normally.
The battery is brand new (1 month) and is fully charged. My hope is that it's the starter drawing too much power when it tries to start? It's entirely possible it has the factory starter still on the car.
View 8 Replies
In the mornings when I turn the ignition switch to on right before starting, I don't hear the fuel pump wining. I notice the wining on almost every other car that Ive drove. I don't know if its because of this I get a rough start. It usually happens only in the mornings especially on cold days. During the rest of the day I can hear it clear and it turns on right away with no problem. I have tried to turn the ignition switch on then off then back on to see if the pump would turn on but nothing. Also sometimes I have to keep the gas pedal down about half ways for it to turn on and not stall. Tomorrow I am going to check to see if any fuel lines are clogged.
Car is a 2000 accent gs 1.5l 12sohc ... With about 87500 miles on it ...
Anything I should replace with these many miles ... Planning to replace spark plugs and timing belt myself ...
View 1 Replies
'04 RX330: Starting about a year ago, occasionally when inserting the ignition key it wouldn't turn to start. Take key out try again and it would start. Progressively, it seems to be requiring more and more in/out cycles to get the key to turn. It's like the transponder is not recognizing the key FOB. I have two keys, one is a master and other is a sub key, both have the problem. What has to be done to correct it? I'm afraid the dealer will just change some expensive ignition part when there's an easier fix.
View 14 Replies
I'm trying to get friend's 04 F150 4x4 started. I think it might be the ignition switch. Here's what I've done. Turn the Key and nothing happens. Not even a clicking sound from the battery.
-verified the battery had a good charge and that terminals were clean, connections were tight.
-checked the fuses in the passenger side kick panel, none were blown
-Determined there was power to the primary Pos wire going to the starter , but no power being sent to the smaller wire that goes to solenoid at the starter.
-Hooked a jumper wire to the starter solenoid and engine did crank (so starter is good and battery is making good connection)
This is why I'm thinking its the ignition switch.
1) Where is the ignition switch located?
2)How can I test the ignition switch?
3)Could it be the "cylinder lock and keys" that is faulty?
View 5 Replies
