Golf IV / Jetta IV :: Installing Remote Start System?
Dec 5, 2012
I'm getting a remote start system for Christmas and I'm looking at how to do the install myself. I know you need a bypass and an extra programmed key for the system to work. This is my problem, My car only came with one switchblade key so I would have to get one made. Basically if I do an immo defeat on my ecu which is tuned (not sure which company a po did it), will I be able to do the remote start without having to use a bypass and spare. Essentially if I do an immo defeat, in order to start the car they key would not have to be programmed, just laser cut, correct? Is it possible to do an immo defeat with vagcom or do I have to get a tuning company to do it. The car is an 01' gti AWW for reference. I'm planning on going gonzo stage 2+ in the Spring so I'm thinking about just waiting until then and getting the immo defeated with that, if it works with the remote start.
View 3 Replies
Advertisement
Can a remote start system be installed on the factory alarm ?
View 11 Replies
So i have been looking to get some new headlights with the projector housing but noticed that most of them have a fog light which my car does not have. I know in order to get them to work properly i would need the euro switch, but would i need to run additional wires through the firewall?
View 8 Replies
There is only one DIY i can find that is still alive. I have a megan short shifter. Its already half way in. I just don't have any instructions and i am kind of at a loss as to where i go from here. Does this shifter change the way my reverse gear will be engaged? I mean will i need to pull the trigger up to go in reverse or will i still push down? Does the spring that came with the kit go under the sleeve or above it? Sounds confusing.
View 3 Replies
How to install rivets to the subframe and rails of the car I can't figure it out to save my life and it just says to put the ecs bolt and but rivet installer but it literally does nothing the rivet literally slides in and out am I missing something.
View 16 Replies
I'm looking at some wheels and the specs are 18x9.5 with 35mm offset, will it poke out or no? I can get them staggered but I would rather not?
Car is a 02 Tdi Golf 4 Door
View 2 Replies
I just picked up a 2000 VR6 golf a few weeks ago. been doing lots and lots of reading. It needs a transmission and was wondering what other things should I do why tranny is out of the way. I know some things can either only be done with tranny out or are a hell of a lot easier with it out of way. So what are your recommendations. Looking to pick up a tranny and get this bad boy on the road asap. Car ran great no issues or sounds my buddie just shifted to 3rd on highway and something walked loose in tranny and kaboom she went.
View 5 Replies
How hard would it be to add remote start to an F450 Lariat diesel? I has everything but i beleive [nav, locks etc...] or was this even an option?
View 8 Replies
So I recently got this GTi and I was wondering what steps I should take before putting a bigger turbo on this car and the steps I should take when putting a bigger turbo. What should I do first be for considering a new turbo?
View 1 Replies
I have a 2006 F250 and it has the stock keyless entry. I would like to have remote start system as well. I know I can buy an aftermarket system, but I'd prefer to no cut any wires. Is it possible to add on the OEM remote start system that may have been used on a superduty or excision of this vintage? and if so, is it a plug in type installation? or do you still have to cut and splice the stock wiring harness.
View 12 Replies
What are the installation instructions for remote start p/n bb5z-19g364-c going into 2011 edge
View 1 Replies
...Just bought a Code CA-6551 for a great price. What bypass module would I need for my 01 F150 to do the remote start?
View 1 Replies
I've been looking for a remote start system to install on my truck it has no remotes of any kind now. I've been googling most of the day and i can't seem to find anything except something that hooks to a edge tuner of some kind.
View 6 Replies
I just installed the Hyundai factory Remote Engine Start in my 2011 Elantra GLS and have a problem that the hazard lights come on and stay on when unlocking/unarming the car. To repeat, this is the genuine Hyundai Accessory Remote Start/Security kit (3X056 ADU00), not a third party offering. Everything that the kit is supposed to do, WORKS as specified, including remote start. The only problem is that when I use the key fob to unlock/disarm the system, the emergency flashers/hazard lights come on and stay on until I turn them off from the inside or until I toggle lock/unlock for the key fob a few times.
I've been through the wiring a dozen times, and am absolutely certain that the kit is wired correctly -- again all features work. Now, I find it interesting that NONE of the wiring of the kit (based on the schematic) comes close to touching a circuit that is identified as hazard/flashers! I even temporarily disconnected all four leads from the kit that go to the front headlamp circuits and rear tail lamp circuits -- and the hazards STILL CAME on when unlocking. This is telling me that there is an indirect/unintended "connection" between the kit and the triggering of the hazard circuit.
The kit is clearly the correct one for the car, and the car has the right equipment for the kit (i.e. No Smart Key, has auto transmission, power windows, power locks, etc). Why the hazard lamps come on when I click the keyfob to unlock the car?
View 6 Replies
2001 MK4 GTI VR6 put brand new coil pack, wires and plugs in the car because it was misfiring. Was fine for about a week than I got a clogged cat code and could feel the affects. I now have no cat, no resonator, and no muffler. The car is finally driving good and then the check engine light came back. It says only a misfire in Cylinder #3 and when accelerate hard to speed up my check engine light starts to blink until I stop accelerating hard. So my guess is the clogged cat caused that cylinder to misfire but I do not know the actual solution to this. My EVAP hose is semi-pinched and when u squeeze it you can almost kill the engine. The weirdest thing of all is this: driving normal I shift in between 2000 and 3000 RPM and once i get into 4th gear about 2000 RPM......my car starts shaking badly and i feel like my engine is going to fall out. I have searched and the only thing i can think of is a bad injector...
View 3 Replies
Soooo the other day i killed my battery, went to get a jump- and after I was running again, i went to unlock my doors and only my driver side door would unlock via my key fob.
Now, the lock function will lock every door, using my key (in the door) will unlock every door. Hitting the unlock button in my car will unlock every door..... just not from my key fob.
View 20 Replies
How do I make my windows go up and down with remote ?
View 6 Replies
Well our remotes only worked close the car and was driving us nuts. You'd have to be within 10 feet or so to arm or unarm the car. So i looked at the wiring diagram for the comfort control module and found which pin the antenna wire is at. Its pin 10 of the smaller connector (12 pin i think) and is a copper wound wire with a clear sheath around it. its the only one that doesn't have a colored insulation around it. I removed the terminal and wire from that slot and installed a new terminal with 6 feet of wire spliced on.
I then routed the new antenna wire along the door sill and to the rear seat area. Its now a 6 foot antenna instead of the small 2 foot one. I then started walking away and arming and un-arming the car. i got to the end of my court (roughly 50 feet) and it was still arming and un-arming even if i held the remote low and not up in the air. Id have to say this was a HUGE improvement and i am much happier not having to walk down stairs to arm the car.
View 24 Replies
My son has a 99 VW Jetta. His car won't start. We checked the battery and starter. Everything is working - lights, power windows, AC... The remote does not unlock or lock the doors. It has to be done manually (before it did). What may be going on?
View 3 Replies
I have changed the batteries in the remote for my MY 2000 Jetta MKIV VR6. Now the remote is not working. A search suggests I need to program the remote using a specific procedure. Alas, I have found various procedures, and so far none has worked.
First of all, I have two keys, Both were functional. One still is.
What I tried:
-Put key with fob in ignition and turn key to accessory mode position.
-Wait 5 seconds
-Hold lock button on 5 down for 10 seconds.
-Turn ignition off and remove key.
-Close doors on car and trey to lock/unlock - not working!
I'm sure I can find a few more suggested methods, but what's the proper method?
View 24 Replies
Im currently installing a remote starter on my 07 camry and it wants me to tie into the "parking light" fuse or wire. It is a Bulldog system, on the website it describes it as "Black (-) wire" located at "BodyECU in vehicle fuse box 26 pin plug pin 23" The fuse box cover does not identify fuses by number and i do not see anything that looks to be parking light related.
View 1 Replies
