Golf IV / Jetta IV :: Installing 18x9.5 With 35 Mm Offset
Aug 21, 2015
I'm looking at some wheels and the specs are 18x9.5 with 35mm offset, will it poke out or no? I can get them staggered but I would rather not?
Car is a 02 Tdi Golf 4 Door
I'm looking at some wheels and the specs are 18x9.5 with 35mm offset, will it poke out or no? I can get them staggered but I would rather not?
Car is a 02 Tdi Golf 4 Door
I have this issue from time to time where I will be driving and my car will randomly stall itself out and shut off. what could be the issue?
2nd I have an issue while idling, where if I am idling I feel a slight vibration like it is about to stall.
3rdly How big of an offset can i have on rear wheels that are 18x8?
The aforementioned questions are regarding a 2004 GLI.
So i have been looking to get some new headlights with the projector housing but noticed that most of them have a fog light which my car does not have. I know in order to get them to work properly i would need the euro switch, but would i need to run additional wires through the firewall?
View 8 RepliesThere is only one DIY i can find that is still alive. I have a megan short shifter. Its already half way in. I just don't have any instructions and i am kind of at a loss as to where i go from here. Does this shifter change the way my reverse gear will be engaged? I mean will i need to pull the trigger up to go in reverse or will i still push down? Does the spring that came with the kit go under the sleeve or above it? Sounds confusing.
View 3 RepliesHow to install rivets to the subframe and rails of the car I can't figure it out to save my life and it just says to put the ecs bolt and but rivet installer but it literally does nothing the rivet literally slides in and out am I missing something.
View 16 RepliesI just picked up a 2000 VR6 golf a few weeks ago. been doing lots and lots of reading. It needs a transmission and was wondering what other things should I do why tranny is out of the way. I know some things can either only be done with tranny out or are a hell of a lot easier with it out of way. So what are your recommendations. Looking to pick up a tranny and get this bad boy on the road asap. Car ran great no issues or sounds my buddie just shifted to 3rd on highway and something walked loose in tranny and kaboom she went.
View 5 RepliesI'm getting a remote start system for Christmas and I'm looking at how to do the install myself. I know you need a bypass and an extra programmed key for the system to work. This is my problem, My car only came with one switchblade key so I would have to get one made. Basically if I do an immo defeat on my ecu which is tuned (not sure which company a po did it), will I be able to do the remote start without having to use a bypass and spare. Essentially if I do an immo defeat, in order to start the car they key would not have to be programmed, just laser cut, correct? Is it possible to do an immo defeat with vagcom or do I have to get a tuning company to do it. The car is an 01' gti AWW for reference. I'm planning on going gonzo stage 2+ in the Spring so I'm thinking about just waiting until then and getting the immo defeated with that, if it works with the remote start.
View 3 RepliesSo I recently got this GTi and I was wondering what steps I should take before putting a bigger turbo on this car and the steps I should take when putting a bigger turbo. What should I do first be for considering a new turbo?
View 1 RepliesRecently had some bad luck and need to get new rims - what's the proper offset for the R? OEM offset is et50 correct? I'm thinking of getting a set of either BBS CHs or RS4s but want to know what the best offset is for the rim.
View 7 Replies2001 MK4 GTI VR6 put brand new coil pack, wires and plugs in the car because it was misfiring. Was fine for about a week than I got a clogged cat code and could feel the affects. I now have no cat, no resonator, and no muffler. The car is finally driving good and then the check engine light came back. It says only a misfire in Cylinder #3 and when accelerate hard to speed up my check engine light starts to blink until I stop accelerating hard. So my guess is the clogged cat caused that cylinder to misfire but I do not know the actual solution to this. My EVAP hose is semi-pinched and when u squeeze it you can almost kill the engine. The weirdest thing of all is this: driving normal I shift in between 2000 and 3000 RPM and once i get into 4th gear about 2000 RPM......my car starts shaking badly and i feel like my engine is going to fall out. I have searched and the only thing i can think of is a bad injector...
View 3 RepliesI have seen it written and noticed it in person that the steering wheel on the b7 does not line up exactly with the driver or the seat. the steering wheel is ~ 1 inch offset to the right of center.
was this done intentionally. URL]...............
I have a lexus sc430 2002.I am going to put 19 inch staggered rims on the car.what the front and rear offset should be so that the wheels clear.
View 13 RepliesI really like the look of cars with 25mm/35mm spacers with stock wheels and tires. But instead of using spacers, are there wheels with proper offsets to achieve the same result?
[URL]
I have a 2004 f150 heritage Super Cab Xlt with the 4.6. It has a fabtech 6' suspension lift on it. And 315/75/16 BFG A/T KO tires. I replaced inner and outer tire rod ends. Steering Box and idler arm. Replaced rotors and brake calipers on the front and brakes. Replaced rear rotors and rear brake calipers.
Now to the point. Lets say the road steers to the left. I have to steer the wheel to the right ad left in order to stay within means of the lane and stay straight. If I am driving on a straight road I always have to have my steering wheel held to the right in order to stay straight. So lets say the road starts turning left. I have to keep the steering wheel held to the right then slightly left.
But I can't just steer the wheel left or right. It seems that it has to be a special way of steering the truck. I have had tires rebalanced and many shops have said the truck is within alignment specs. It always seems that the steering wheel has to have a offset. Could something else be wrong with the truck ? frame ? u-joints ? Steering wheel column ?
A new problem with the navigation system display on our 2010: the radio station buttons are mapping with an offset.
In other words, I press the top left preset button, and get the radio station two positions down. If I want the top left station, I must select an area well above that station on the touch screen.
Is there a way to reset the touch screen so that it maps correctly?
I installed the pierburg revised DV yesterday because my old DV was shot, squealing and leaking boost. After installing it I noticed that when i'm under around 15 psi and i let it build up that I get this flutter I didnt have before. I assume its the wastegate but I haven't heard it prior to installing the new DV so my fear is that its the valve no circulating and its putting the unused psi back through the turbo (not good).
View 7 RepliesWhat combinations of wheel width and offset have you tried? My goal is to have my wheels perfectly lineup with the fenders.
View 4 RepliesI just installed a new offset high torque gear reduction starter on my 2000 Excursion, and I noticed it starts much faster, but it sounds like the starter is knocking against something. Is this a straight swap out with the old style starter, or do I need to modify something?
View 14 Replies-I currently have a CTS turbo intake, 42DD turboback and installed the Autotech HPFP. After we installed the HPFP and drove around the block I threw a CEL. (not sure the exact code # ) but it was related to the cam shaft.
We were unable to upload the 2+ tune because his computer which has his APR info is under repair. My guess is that I am throwing a CEL because I upgraded the HPFP but do not have a tune for it yet. Who else has installed a HPFP before getting the tune?
I have a 2013 gti. Lowering it in h&r super sports. I want some spacers to complete my look on the 50000km a year Car. Would 20mm spacers all around be to much?
View 2 RepliesI'm interested in installing a staggered set of wheels on the R. The size I'm looking are 18x8.5 and 18x9.5. My question is what wheel sizes should I run to keep everything within spec of my Haldex unit? Ive read about staggered units having to be within 3 or 4% so nothing breaks down prematurely.
View 24 Replies