My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 RepliesSo my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 RepliesI have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
2001 jetta 2.0 VW guys a while back I was pulling a code saying that the air temp sensor circuit was low I believe it was P0112 so I replaced the maf with a bwd maf. Said it was for the car. Was fine for a day but now it has a P0102 code and the epc stays on (rough idle) what could be wrong ? Is it because the car hasn't learned the new sensor yet because I've only drove 10km or do I have a faulty sensor. BTW replacing the maf fixed the P0112 code
View 5 RepliesI recently got the solid check engine light for my 2003 VW Jetta 1.8T GLS. I used a bluetooth OBDII dongle and Torque Pro to pull the code P0118. This seems to coincide with my symptoms:
Car idle at start in park stays around 1100RPM then in reverse it drops to 1000RPM then back into park and it stays around 900RPM and keeps that at idle.
If I start the car then immediately reverse out of my driveway then the car has a very rough idle but if I wait around 5 seconds in park idle then reverse out of my driveway it is smooth.
My car dash thermometer stays pretty close to the bottom low then after about 4-5 minutes it shoots up to 190F and stays. Gas mileage is also very poor.
I looked up a tutorial which shows the parts needed and how to replace the sensor : [URL] .....
I removed the engine cover and believe I found the coolant temp sensor in the spot the tutorial shows. My question is if there is anything I should be aware of before attempting to replace this sensor that this tutorial doesn't cover? I took a screenshot of what I believe is the coolant temp sensor.
I have a 03 GLI 24v VR6 thats throwing a P0113 code, which is for the intake air temperature sensor. The sensor is part of the MAF sensor, ive tried 2 brand new BOSCH MAF sensors yet the same check engine continues to reoccur. Is there anything else that oculd be triggering it to come on? Is there anyway to bypass/disable it through vagcom?
View 8 RepliesI have a a 02 jetta 1.8 turbo the code po343 came up after new temp sensor,valve cover gasket and full tune up. is it an easy fix the car is misfiring an very hard starting.
View 1 RepliesNow I've had this constant problem with this code that I just cannot get rid of. I've read many threads on here but nothing seems to be working. I currently am on the third maf that I've been able to test out, still throws the code. Connector is all clean, nothing wrong there. It is clean every time I just can't figure it out.
View 3 RepliesP3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 RepliesSo the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
I have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 RepliesSo my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
Looking at my circle track car when they told me my air intake temperature sensor was missing this is a picture online I found: [URL] ....
The hole is filled with a bolt and some epoxy. I don't see where the cable is for it. What will this do to my car? It is a track only car.
I have a 02 2.0 Jetta with 179k
Have that pesky "whistle under acceleration" when past 1/4 throttle issue. I have been going over the entire engine, checking and cleaning.
-----On the intake tube where the 1 inch case vent and half inch tube meet there is a Flapper/Flow check with a electrical connector directly on top.
Question being, is this a flow sensor? The flapper is distorted and does not function properly.. is this an issue?
I've tried to do my due diligence searching on this (I've seen many posts but most have other codes).. I have the P000A code, reads as follows-- Intake (A) Cam Position Sensor Slow Response (powertrain).
I have no misfires, hesitation rough idle, nothing. I have 94k miles and I always done my oil changes @ 5k intervals and I have not had any prior engine maintenance done to the car....
I took my R32 to the local VW dealer today and they are saying they believe it might be the time chain tensioners. I am wonder if this could be a simple sensor issue since the car runs perfectly fine, I just get the engine light coming back on after 1 to 2 weeks of clearing the code. I have had this issue since January and I thought it might be the cold weather here in WI.
I dont see anything attached to the manifold....
View 10 RepliesThrew a coolant temp sensor code yesterday morning:
16502 - Engine Coolant Temp. Sensor (G62): Signal too high
p0118 - 002 - Lower Limit Exceeded - Intermittent - MIL ON
Does throwing that code once mean I need to replace the CTS immediately or am I safe to clear the code and see if it returns? No code today after a 40 minute drive.
Where the ambient temp sensor is located on my 02 Golf 2.0.
View 5 RepliesI just replaced my CTS, and I noticed that there is a small section of exposed harness wiring between the end of the loom and the CTS connector. I can't tell if it came loose when I swapped the sensor, or if it was this way for awhile, but all of the other harness connections around this area are completely covered and the loom end doesn't seem to clip into the connector or anything. If I were to try and seal it, I would need to use tape.
How hot does this area get? It seems like there shouldn't be exposed wiring here.
Picture taken with the new sensor: [URL] ...