Golf IV / Jetta IV :: Cruise Not Working / Clutch Pedal Switch Test?
Nov 30, 2015
03 Jetta. The cruise has not been working. Turning cruise on and off works fine as light comes on on dash. Brake pedal switch was replace about a year ago, and I don't think that is the problem because when this was the car would actually go into limp mode.
Just checked the clutch pedal switch by jumping the plug (This was the blue switch lower on the pedal), and still no cruise function. I'm really leaning toward it being the "set" switch/button on the steering wheel as this just feels kinda broken. Did I test the clutch pedal switch correctly? Any other reason the cruise would stop working?
View 9 Replies
Advertisement
I changed my brake light switch, and i had my buddy check it with vagcom and now I am getting a clutch pedal switch fault and I am also getting a clutch mechanical fault in my rear end what the most probable cause of this, could it be the clutch pedal switch causing a mechanical fault?
View 4 Replies
So noticed my cruise control does not work when I turn switch to on position the green light in cluster does not come on what are some problems that I could look into and also any example of using turn signal Bulbs in the head lights as drl lights instead of it running off of the actually headlight bulb?
View 9 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
I've done a bit of research both here and on other sites. I originally thought that I had a bad flywheel but I'm not convinced. First I'll give a little backstory. I just installed steel shift forks because one broke and got jammed in the gears. None of the gears are damaged and I assumed that when it slammed to halt, the flywheel got messed up. So anyways, the complaint is that when the clutch pedal is released I start to hear a knocking sound which becomes more rapid with RPM. When the pedal is depressed the sound goes away. This sound seems to be coming more from the driver's end of the trans. The car still moves in all gears so I can't imagine that I put it together wrong.
View 6 Replies
2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 Replies
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 Replies
So last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
View 3 Replies
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
The cruise worked perfect before I lowered the car and now it works occasionally.. It was on most of the 10 hour drive to this part of Florida and around town it's worked but has started to act up a bit again now.. Sometimes the cruise light will flash and then won't work but other times it's fine any input? The car is an otherwise stock AWP at 107k miles..
View 2 Replies
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 Replies
I am proud new owner of a 03 Mk4 Bora GLI. I have some issues that I could use a hand with. My symptoms are as follows:
1. Speedometer stopped working.
2. Fuel gauge goes on the fritz (rapidly declines) when parked on an incline or going around corners.
3. Cruise control does not work. "Cruise" light come on the dash but the set/reset button on the stalk does nothing.
Note: All fuses are in tact.
View 3 Replies
Today I pulled off the front bumper assembly to install an oil pressure gauge. The wire that goes from the sender to the gauge I pulled through A rubber boot that had a cluster of wires located next to the driver side windshield wiper, I pulled the wire through with a coathanger or I could've scratched another wire which is causing the gas pedal not to work? Or could it be when I pulled off the bumper assembly something unplugged or broke? VW GTI VR6.......
View 1 Replies
Any way to test the radiator temp sensor for faults? My radiator fans arent kicking on, and my car will get upto 215f on the drive to work. I am also going to replace the thermostat and test my radiator fans and relay today, but I have no idea how to test the sensor.
View 3 Replies
I recently bought this golf and well gotta say very happy with it, W reg so 2000 model and it the 1.9 TDI SE variant, 29,000 miles and only one owner from new. But like many before me I have a air con issue.
So here's what I have looked at. Done the climatronic test with two error codes
04B6 Standing Time Signal
0318 Air Conditioner Pressure Switch
The blower works inside etc, but only blows warm air. I can hear the engine rev's change when I push the Econ button. So car is pretty mint but 15 years old, where should I start looking.
View 18 Replies
About 4 months ago I was at the gas station and when I tried opening my fuel door, the switch wasn't working. I went home, took the door trim off, and then removed the switch in order to clean it. Once I cleaned it, it worked but about every 3rd time that I clicked it. However, yesterday it finally gave out as I was at the gas station. So I came home and now I'm stuck because I don't want to break the fuel door.
I ran through the fuses in the fuse box but on the diagram none seem to be for the fuel door. The weird thing is that yesterday as the fuel door switch gave out, so did the interior door lock switch. Now I have to insert the key from the outside in order to enter the car. But the key cannot unlock the passenger door.
When I hit the interior door lock switch, I hear a click noise under the dash. I took a look under there and it seems to be a bunch of relays. It's very tough to tell which one is the one clicking.
View 2 Replies
A few years ago I had the clutch changed on my 1997 F150. Afterwards the cruise control wasn't working. When I brought the truck back to the repair shop I heard the manager tell the mechanic to "attach the clip by the pedal" and that fixed it.
I just had some work done, had to replace the oil pan, and the mechanic had to remove the transmission. Now the cruise control doesn't work. I changed the Pressure switch but it didn't fix the cruise control. What that clip might be that fixed the cruise control last time?
View 3 Replies
My AC clutch, radio, cruise control, and turn signals are not working. I have checked all fuses and relays that I can find, all good. From what I have read, these are not part of the GEM function. What I need to check next!
View 7 Replies
I own a mazda 3 6 speed and im curious as how to test my clutch for slippage. I read on a old forum that to put the e brake up and put the car in 1st gear and release the clutch. When i did that my car tried to move but after a couple seconds i put it back in neutral. Another forum said to do the same but put it in 3rd as i released the clutch it stalled right away.
View 5 Replies
F250 6.8L .. So Ive read a lot of posts about intermittent cruise control issues. I understand that the most common failure is the brake switch on the master cylinder. My concern is that I am unable to run the cruise control self test I keep reading about. Does this test not work on my model year. I have tried even when the cruise control is working and still the cc light does no come on.
View 2 Replies
