Golf IV / Jetta IV :: Clutch Pedal Feels Soft Since Replacement - No Air Coming Out
Jan 6, 2015
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 Replies
Advertisement
Just the other day I got the clutch replaced on my 06 WRX. I took it to a reputable workshop that I've dealt with before. When I got it back the clutch pedal feels very soft and goes to the floor with ease, whereas before it was a lot harder and felt good. It works good and dosen't slip but just a soft pedal. I also went for the OEM replacement and not aftermarket. Some of the google searches I've read say the pedal will get harder after about 1000-2000 km.
View 5 Replies
Just as the title states. When I put the AC on in the car my clutch pedal gets some play in it, enough that it messes up shifting and gets jerky. I tried searching, but no results
View 14 Replies
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
View 3 Replies
I have had everything related to the clutch changed, and I even had a dealership bleed the clutch line. The problem is the clutch pedal is soft and will sometimes work good and sometimes won't. If I prop the pedal to the floor for a few hours, it works fine for the day. what gives?
View 1 Replies
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 Replies
We have a 1997 Mitsubishi Eclipse with a hydraulic clutch. The pedal is very soft in the morning and requires a good bit of pumping the pedal to get good pressure. I know the system needs to be bled. Does this mean one of the cylinders is bad? I have added a little bit of fluid over the last year- maybe 2 or 3 ounces total. Right now the fluid level seems fine but it still needs to be pumped before driving.
View 7 Replies
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies
I am not very familiar with transmissions and clutches, hence I just purchased a used transmission for my jetta 1.8t, i was told that i might as well do the clutch while the transmission is getting done. I just purchased the car two years ago and the guy said that he put a vr6 clutch in. so my question is, what exactly will i need to get for both the transmission and clutch replacement. Like I mentioned, I only have bought the transmission so far.
View 6 Replies
I have a 92' Escort GT and the clutch started to act up, it's not burnt cause it is fairly new. The clutch pedal feels slightly looser when pushing it to the floor, the feeling like a cable snapped or something?
I'm pretty sure the clutch is a hydraulic one, not 100% .. Is there a hydraulic reservoir that somewhere that might be low?
View 4 Replies
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
I've done a bit of research both here and on other sites. I originally thought that I had a bad flywheel but I'm not convinced. First I'll give a little backstory. I just installed steel shift forks because one broke and got jammed in the gears. None of the gears are damaged and I assumed that when it slammed to halt, the flywheel got messed up. So anyways, the complaint is that when the clutch pedal is released I start to hear a knocking sound which becomes more rapid with RPM. When the pedal is depressed the sound goes away. This sound seems to be coming more from the driver's end of the trans. The car still moves in all gears so I can't imagine that I put it together wrong.
View 6 Replies
2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 Replies
03 Jetta. The cruise has not been working. Turning cruise on and off works fine as light comes on on dash. Brake pedal switch was replace about a year ago, and I don't think that is the problem because when this was the car would actually go into limp mode.
Just checked the clutch pedal switch by jumping the plug (This was the blue switch lower on the pedal), and still no cruise function. I'm really leaning toward it being the "set" switch/button on the steering wheel as this just feels kinda broken. Did I test the clutch pedal switch correctly? Any other reason the cruise would stop working?
View 9 Replies
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 Replies
So last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
View 3 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 Replies
Having clutch issues? I have just put 10k miles on my JSW and the clutch feels like it slipping in 1st gear when heavier load(uphill ETC) is present its even worse. We have never drove it hard pretty much cream puff.
View 9 Replies
I just got my new 2014 RX350 a few weeks ago. After these weeks drive, I feel the Brake is kind of soft and unsensitive.
When I braking, the first part of the brake pad feels soft and the braking is not very efficient, until I push a lot of the brake pad, the braking becomes confident and efficient.
I used to drive my 2006 Nissan altima , and feels the brake pad is very sensitive. My new lexus makes me a little bit unconfident when following a car in a short distance.
View 2 Replies
