Golf IV / Jetta IV :: Climatronic Test With Two Error Codes 04B6 And 0318
Jul 6, 2015
I recently bought this golf and well gotta say very happy with it, W reg so 2000 model and it the 1.9 TDI SE variant, 29,000 miles and only one owner from new. But like many before me I have a air con issue.
So here's what I have looked at. Done the climatronic test with two error codes
04B6 Standing Time Signal
0318 Air Conditioner Pressure Switch
The blower works inside etc, but only blows warm air. I can hear the engine rev's change when I push the Econ button. So car is pretty mint but 15 years old, where should I start looking.
View 18 Replies
Advertisement
I was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 Replies
So my car has been running a little rough for a while(about 6-8 months now) and the CEL has been going off sporadically. The clutch went out last week and has been replaced fixing a large part of the issue, however the car still feels kind of rough in the 3k rpm range and up. I feel a strong vibration when I step on the throttle and the car hesitates to build power. On cold starts the car also has a rough idle where the rpms are hovering above 1k for a few minutes.
I recently took the car over to AU Tuning where they gave me a free diagnostic(Pacific German was charging me $100 just for a diagnostic!?). They told me the throttle body might need a cleaning but I was better off replacing the whole unit. They also discovered my air intake hose torn near the diverter valve and a 5 bar Fuel Pressure Regulator that was pressed in for added pressure.
Given that I just replaced the clutch, funds are tight and I don't have the money to replace everything right away
I should mention VAG-Com reported the following codes:
P1137 Fuel Trim: Bank 1 - System too Rich,
P1297 Pressure Drop between Turbo and Throttle Valve (check D.V.!)
P1171 Angle Sensor 2 for Throttle Actuator(G188) Implausible Signal
View 5 Replies
I'm having some problems with my 05 1.8T GTI. I've had a check engine light for about 3 months and finally got a diagnostic tool (VAG V-checker). Right now I have one code 17748.P1340 Camshaft position sensor-G40/engine speed sensor -G28: incorrect allocation.
I researched a little bit and talked with some of the guys at the local VW dealership. From what I learned this could be related to (obviously) faulty camshaft position sensor and/or faulty engine speed sensor. So I've replaced both of these sensors and even cleaned the Mass Airflow sensor.
I cleared the code and after driving about 5 minutes the code came back. Also I recently had a P0300 and P0304 cylinder 4 misfire default code. So I've changed all of the ignition coils too since I heard they were recalled a while back.
View 2 Replies
I've looked all over online about this and spent hours tinkering with it but I can't seem to figure it out. I have an '01 gti glx with the lcd climatronic. fully functional but none of the backlights work for the buttons or the screen and I'm wondering what at all it could be... Not a hugely pressing issue, just annoying trying to figure out which button is which at night..
View 1 Replies
My display on the MFA and Climatronic panel is really wrong (-44C now). I was taking a look at the sensor in the front left grille but the only thing that's changing into the readings with my Vag-Com is the outside temperature sensor but not the displayed temperature.
I didn't find any other sensor on my car. Nothing into the rain tray...
View 6 Replies
Any way to test the radiator temp sensor for faults? My radiator fans arent kicking on, and my car will get upto 215f on the drive to work. I am also going to replace the thermostat and test my radiator fans and relay today, but I have no idea how to test the sensor.
View 3 Replies
03 Jetta. The cruise has not been working. Turning cruise on and off works fine as light comes on on dash. Brake pedal switch was replace about a year ago, and I don't think that is the problem because when this was the car would actually go into limp mode.
Just checked the clutch pedal switch by jumping the plug (This was the blue switch lower on the pedal), and still no cruise function. I'm really leaning toward it being the "set" switch/button on the steering wheel as this just feels kinda broken. Did I test the clutch pedal switch correctly? Any other reason the cruise would stop working?
View 9 Replies
I just has a gen 2 haldex and wireless controller installed. 10 minutes of driving around getting on it in sport mode, I feel a thunk from the back and when slowing down a few odd shudders. Drove it cautiously a bit more and felt fine, then harder and harder. Felt better, no understeer, seemed ok.
Got home and scanned with Vagcom, got the errors below, cleared DTC and scanned again, same errors.
Address 22: AWD Labels: None
Part No: HW0 5Ha lde x
Component: Tuning
Coding: 0000001
Shop #: WSC 00000 000 00000
VCID: 5AB1BED4953067CEBA7-800F
2 Faults Found:
16347 - Control Module - EEPROM Error
014 - Defective
02248 - Valve for Controlling Clutch Operating Angle (N373)
014 - Defective
View 3 Replies
I'm reaching out to see if any other MQB platform owners who had DCC/Magride are experiencing suspension errors after upgrading to coilovers while employing a delete kit. Some of us S3 owners have been running into this issue after such an upgrade and using this kit by KW. I can throw a suspension error on demand in my S3 by taking a turn/curve at 40mph+ (highway on/off ramps work perfectly for this). A bumpy road or hard braking can also cause an error to be thrown.
Aside from the error being annoying sounding and looking it also re-enabled traction control. You cannot turn traction control back off until you've power cycled the car. This is a pretty annoying side effect that could also be pretty dangerous under the right circumstances. KW seems to think their kit is operating correctly and that the height sensors are out of range due to lowering the car. Currently there's no way to adjust where the height sensors sit so in my personal opinion this seems like a massive oversight on KWs part and their product is not working correctly.
View 3 Replies
Add a few codes come up today ... P2187 & P218. Bank 1 & 2 running lean at idle
Haven't been able to find a definite answer..
Replace purge valve?? (P/N?)
MAF??
Fuel filter??
I keep getting engine codes and 265 miles per tank.
View 19 Replies
I just tried doing the self test for reading the codes via the check engine light with the OBD1 system on my '93 4.0 Ranger. Problem is: When trying to mark down the flashes of the check engine light, they flash so erratically and rapidly that there is no way to accurately count. At times the light flickers so fast it never even gets to get fully bright enough to tell if it is actually a "flash" or not. I'm (again) trying to diagnose an issue with the truck starting and running fine for about 3-4 minutes and then like flipping a switch begins blubbering and belching out black smoke, check engine light flashes on/off randomly, then the engine will eventually die. It will restart provided the ignition switch is turned all the way off and attempted again, generating same results only within 30 seconds or so. If you try restarting w/o turning the ignition all the way off, it'll spin over but won't start. ECM?
View 4 Replies
Any LED I can throw in the footwells / license plate area that won't throw a code? I'm using the ones from superbrightleds.
They worked everywhere except the license plate and the footwells. Everytime I get in my car I have to see (check license plate lights!) and a bulb out icon.
View 10 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
Whenever I hit auto on the climatronic after the car has been off it always defaults to 72 degrees. I'm in South Florida, and I realize it's a little thing, but it'd be great if I could make it default to low right off the bat. Is this something Vag-com could be used to alter? Tried searching for this but couldn't find anything directly related.
View 1 Replies
On start up, on the hot day, A/C takes 4-5 minutes of driving before starting to cool. Not much cold air coming out once it get's going to.... IF Climatronic is switched OFF, then as you drive you can feel hot air coming out from vents and actually fogging up windscreen on the rainy day.
View 8 Replies
So driving on the highway my car died. It would crank but not start. Got it towed. This is what I have done to troubleshoot.
1. Swap ECUs. The car should start for a second and shut off because the car doesnt match with the ECU. Still just crank and no start.
2. Fuel pump still primes when I open the door. I also hear a weird air leaking noise when I reconnect the battery, but I think it comes from the fuel pressure regulator (which I think is normal).
3. Checked for current at the ecu wires, wasn't sure what to look for but it was getting numbers.
4. Battery had 12.1 volts running through it (Haynes said 12.5 but is that really much of a difference?
5. Checked spark plugs for spark. Pretty sure we did it right, but there was still no spark. We tried multiple times.
6. Scan car, get code P01314 twice (ECM error).
7. Try to clear codes, says Comm error.
Why am I not getting spark? and why is the ECU error occurring, because we tested with a new ecu, and there was still no start, not even for a second like there should be.
View 12 Replies
CDP ERROR 3. I have the OEM Premium CD player on my 2002 GTI and it is holding my CD hostage. What do I have to do to get the CD out, and once I do, will it continue doing this, or is it just some random malfunction? i want my CD back...
View 20 Replies
So finally got past the smog cert issue and a bad map sensor in the intercooler. However, during the smog test, I was informed I am getting low air pressure in the intake! What causes this? A bad MAF? a leak? I have replaced the EGR, and all rubber that connects hard pipes. The only piece not changed out during the rebuild is the plastic flex line from the airfilter box to the turbo intake.
View 2 Replies
When checking my check engine light , I got P0021 a cam timing error, but my mk4 Gti runs perfectly ??
View 4 Replies
Damn car is stuck in 3rd gear! Hooked up scanner and the screen just says error! I have to keep the scanner in the vehicle, hooked up, just to drive the car. That's just so it'll shift as its supposed to! Now it's not letting me pull the code out, in order for me to erase it! It just keeps saying "error".
View 1 Replies
