Golf IV / Jetta IV :: Check Engine Light With Error Codes 17748, P1340
Jul 13, 2015
I'm having some problems with my 05 1.8T GTI. I've had a check engine light for about 3 months and finally got a diagnostic tool (VAG V-checker). Right now I have one code 17748.P1340 Camshaft position sensor-G40/engine speed sensor -G28: incorrect allocation.
I researched a little bit and talked with some of the guys at the local VW dealership. From what I learned this could be related to (obviously) faulty camshaft position sensor and/or faulty engine speed sensor. So I've replaced both of these sensors and even cleaned the Mass Airflow sensor.
I cleared the code and after driving about 5 minutes the code came back. Also I recently had a P0300 and P0304 cylinder 4 misfire default code. So I've changed all of the ignition coils too since I heard they were recalled a while back.
View 2 Replies
Advertisement
My check engine light recently turned on but I don't know what the codes mean. The codes are:
16804
17511
17748
16524
View 1 Replies
I just replaced my timing belt. Checked it at TDC several times, even after releasing the tensioner. Now Im getting a
17748 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28): Incor. Correlation
P1340 - 001 - Upper Limit Exceeded
View 4 Replies
A couple of weeks ago the check engine light came on and when I had the codes checked it showed a problem with the EGR valve. I replaced it and the light went off. A week later the check engine light came back on but when I had the error codes checked there weren't any. After a few days the light went off but earlier today it came back on. There are still no error codes.
I forgot to mention that it's a 2000 Camry, 6-cyl.
View 4 Replies
Just tried to leave for work and my check engine light came on. Luckily I just got a scangauge and the error codes are P0441 and P0445. I checked online and for regular Prius is says it could be the fuel system, fuel cap, etc. I'm scared to drive it now and wonder if I should call Toyota Care to tow my car to service.
View 6 Replies
My 1998 Explorer with 120,000 mile on it. The check light just came on. I have had several auto part stores plug in the scan tool and there were no error codes. I'm looking for the reset button location. I am also wondering should there be something missed by the scan tools, will the light activate should there be a real problem.
View 9 Replies
2 error codes? Car runs fine - nothing seems wrong - the check engine light went on, so I pulled out the scanner which came up with the 2 codes: P0021 and P0022.
View 8 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
2001 volvo s40. Diagnostics performed. Error codes for the timing belt and temperature sensor. These were replaced. The check engine light still comes on/stays on.
View 6 Replies
I have a 2000 Toyota Sienna that has had a check engine light for a while. The light would come at times, and go away at others, with prolonged intervals (days, weeks, months) with or without the light.
Suddenly it started losing power, especially on hills (even a small hill). The codes I read are (I include code interpretations from internet search):
P0300: Random or multiple misfire.
P0301: Cylinder 1 misfire.
P0304: Cylinder 4 misfire.
P1130: Air fuel sensor
P1150: I have not found a problem definition for this code.
Might these codes be indicative of a particular problem, or is each problem more likely a problem with its own cause?
View 19 Replies
'01 Audi A6 2.7T, has 97k...I noticed the car making a loud clacking/taping sound at idle that didn't change even when car warmed up. Check engine light came on today...codes P1340 and P0341 both deal with camshaft being "out of sequence" on bank #1.
View 7 Replies
I was cruising down the highway and my check engine light came on. I was a few minutes from a auto store and they said my code was p1296. I found out it is either the thermostat or the coolant temperature sensor. I wanna know where it is located in the engine bay. I have a 02 VW Jetta 1.8T.
View 1 Replies
So I started up my 12v VR6 the other morning and it sounded like a Subie. Threw the awful code P1340: cam/crankshaft sensor out of sequence, and took it to the shop. I'm being charged $1900 for servicing the timing chains, only. Doesn't include water pump and clutch like every other shop does. Reason for this is because in Montana, no one works on these cars. So I this is my only route. I had to choose this small euro repair shop or the VW dealer.
But, they just recently called me and told me I need to get the timing gears changed or whatever? They want to charge an additional $600 or so to do that. Are these gears a real problem? or are they just trying to F me. I mean, $1900 should make this car flawless as it is so I feel that they are attempting to rip me off even more.
View 3 Replies
I was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 Replies
So my car has been running a little rough for a while(about 6-8 months now) and the CEL has been going off sporadically. The clutch went out last week and has been replaced fixing a large part of the issue, however the car still feels kind of rough in the 3k rpm range and up. I feel a strong vibration when I step on the throttle and the car hesitates to build power. On cold starts the car also has a rough idle where the rpms are hovering above 1k for a few minutes.
I recently took the car over to AU Tuning where they gave me a free diagnostic(Pacific German was charging me $100 just for a diagnostic!?). They told me the throttle body might need a cleaning but I was better off replacing the whole unit. They also discovered my air intake hose torn near the diverter valve and a 5 bar Fuel Pressure Regulator that was pressed in for added pressure.
Given that I just replaced the clutch, funds are tight and I don't have the money to replace everything right away
I should mention VAG-Com reported the following codes:
P1137 Fuel Trim: Bank 1 - System too Rich,
P1297 Pressure Drop between Turbo and Throttle Valve (check D.V.!)
P1171 Angle Sensor 2 for Throttle Actuator(G188) Implausible Signal
View 5 Replies
I recently bought this golf and well gotta say very happy with it, W reg so 2000 model and it the 1.9 TDI SE variant, 29,000 miles and only one owner from new. But like many before me I have a air con issue.
So here's what I have looked at. Done the climatronic test with two error codes
04B6 Standing Time Signal
0318 Air Conditioner Pressure Switch
The blower works inside etc, but only blows warm air. I can hear the engine rev's change when I push the Econ button. So car is pretty mint but 15 years old, where should I start looking.
View 18 Replies
My daughter's 2000 Jetta with a 2L has an engine light and codes that state Misfire on 1 and 4. It is intermittent as it only misfires once in a while.. She is in Rolla MO, and I am in Detroit MI. A couple of years ago the car died when she was home and I found a swollen/cracked coil pack. I replaced it with an aftermarket. The plugs and wires were replaced about 30k ago with OEM parts. I am tempted to have the son in-law replace the coil pack with a Bosch unit.
View 3 Replies
So for the past few weeks my check engine light has been on. I have a mechanic friend that scanned the computer and says i have a running lean code.... says it could be anything. So i have been driving the car since and now the epc light and drive train lights are coming on... car revs up and down and sounds like is going to die... got the car scanned and says something about the throttle position sensor... before all the lights started coming on i got my fuel pump replaced..... could a faulty fuel pump be the cause? I had my mechanic, clean the throttle body and it ran good for a few days... now the problem is back... I have a 2004 1.8 gti. Do i have to replace the throttle position sensor? Fuel pump again? New throttle body again? I read somewhere on here that a guy replaced some wires near the ECM and the problem went away...
View 7 Replies
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
View 8 Replies
My Lexus was working fine till yesterday, but today when I started (button press) it, it started giving me a Check VSC error and Check engine light along with Slip Indicator started showing up
Took it to Autozone for the codes and got
P0015
P0304
C1201
B2799
View 7 Replies
So I get back from being stationed in Korea for the past 2 years. I get my car out of storage and the check engine light is on. I scan it and get P0601. I do some searching on the Tex and see that it's the ecu. I'm tuned on APR. the question is can I take it to a local APR dealer here in Houston and get the ecu looked at?
View 6 Replies
