I was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 RepliesI recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Okay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
My van stumbling upon acceleration. Well now I am getting the following codes and the van barely has enough power to move. The codes are: P1860 Enhanced: Tcc Pulse width modulation sol ckt electrical, P0758 Shift sol B ckt electrical, PO755 Shift Sol B malfunction, PO740 TCC ckt malfunction
View 7 RepliesI bought a gorgeous red 4.0L V-6 Mustang very cheap last week because it needed a clutch. I would not even pull the car. Little did I know that the clutch kit, including the slave cylinder and flywheel, was over $600. (But that's another story.)
The car runs now, but will not go over 3800 RPM in any gear. It had NINE codes, which they cleared. I was told that they primarily pointed to the MAF sensor. I cleaned it with the recommended aerosol. I have driven it 20 miles, and the MIL has not returned, but the little wrench symbol has. The Manual says to take it to the dealer (of course). The car seems to run fairly well, with the exception of the low rev limit. It is a "fly by wire" set up, with electronic throttle.
The cleared codes were P0102, P0113, P0135, P0141, P0155, P0161, P0403, P0443, and P0446. They actually repeated on Autozone's scanner. (My six year old Actron won't link to this car for some reason.
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
So my car has been running a little rough for a while(about 6-8 months now) and the CEL has been going off sporadically. The clutch went out last week and has been replaced fixing a large part of the issue, however the car still feels kind of rough in the 3k rpm range and up. I feel a strong vibration when I step on the throttle and the car hesitates to build power. On cold starts the car also has a rough idle where the rpms are hovering above 1k for a few minutes.
I recently took the car over to AU Tuning where they gave me a free diagnostic(Pacific German was charging me $100 just for a diagnostic!?). They told me the throttle body might need a cleaning but I was better off replacing the whole unit. They also discovered my air intake hose torn near the diverter valve and a 5 bar Fuel Pressure Regulator that was pressed in for added pressure.
Given that I just replaced the clutch, funds are tight and I don't have the money to replace everything right away
I should mention VAG-Com reported the following codes:
P1137 Fuel Trim: Bank 1 - System too Rich,
P1297 Pressure Drop between Turbo and Throttle Valve (check D.V.!)
P1171 Angle Sensor 2 for Throttle Actuator(G188) Implausible Signal
I recently bought this golf and well gotta say very happy with it, W reg so 2000 model and it the 1.9 TDI SE variant, 29,000 miles and only one owner from new. But like many before me I have a air con issue.
So here's what I have looked at. Done the climatronic test with two error codes
04B6 Standing Time Signal
0318 Air Conditioner Pressure Switch
The blower works inside etc, but only blows warm air. I can hear the engine rev's change when I push the Econ button. So car is pretty mint but 15 years old, where should I start looking.
I'm having some problems with my 05 1.8T GTI. I've had a check engine light for about 3 months and finally got a diagnostic tool (VAG V-checker). Right now I have one code 17748.P1340 Camshaft position sensor-G40/engine speed sensor -G28: incorrect allocation.
I researched a little bit and talked with some of the guys at the local VW dealership. From what I learned this could be related to (obviously) faulty camshaft position sensor and/or faulty engine speed sensor. So I've replaced both of these sensors and even cleaned the Mass Airflow sensor.
I cleared the code and after driving about 5 minutes the code came back. Also I recently had a P0300 and P0304 cylinder 4 misfire default code. So I've changed all of the ignition coils too since I heard they were recalled a while back.
My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
Not real familiar with this code, given that my check engine light came on a couple weeks ago and they detected some errors and these codes appeared.
View 2 RepliesI have a 2001 Jetta GL 2.0... For the past could of months I have had a mysterious oil problem. I constantly have to put oil in. I have changed it. Always put in the correct amount, right around 4qts. I have changed the head gasket, no leak there anyways and there still isn't a leak. I checked the exhaust and I'm not burning oil. I am completely stumped. What else could be happening to the oil? I just changed my oil about 1200 miles ago and I have already added another 2qts. That is just insane. I have gotten to the point where I am checking my oil every single time I drive to work and back, daily. I do all my own work and have never once noticed any leaks of any type. Something is sneaking by me though.
View 4 RepliesGetting an emissions code. I deleted the emissions with the delete kit. Used the plug in resistors that came with the kit that is supposed to keep the cel off. Here's the code.
P1426 evap emission system purge control valve circuit open .
so my girls car is throwing an evap code (P0442) small leak detected. I bought a new oem gas cap and replaced the purge valve solenoid under the hood. that didn't work, CEL still comes on about 100mi after clearing the code.
I have checked the rubber hoses that were attached to the purge valve solenoid when i replaced it and they are fresh, no dry rot or cracks that i can see. The hose on one side goes to a hard line that runs under the car to the back, the hose on the other side of the solenoid runs under the intake to the throttle body. That hose was fine as well. Connections were tight and i even put better clamps on the hose ends that attach to the solenoid. So I have ruled out that portion of the system (under the hood).
I also removed the rear seat to access the fuel pump. All those connections seem nice and tight, I don't smell any strong gas fumes indicating a leak so i don't think the fuel pump gasket is the problem either. Finally, i checked out the hard lines running under the car front to back and I see no apparent or obvious damage. I assume my next step is to pull off the rear passenger wheel well liner and asses the charcoal canister and the LDP connections, correct??
The last thing I will mention is, Idid notice the 2 fuel lines that attach to the fuel regulator are in pretty rough shape, however not leaking any fuel. Are both of these lines actual liquid fuel lines? I am thinking one of them is a vapor return which may be part of the EVAP system. If it's dry-rotted and leaking vapors could that be the culprit??
I got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.
View 4 RepliesI just has a gen 2 haldex and wireless controller installed. 10 minutes of driving around getting on it in sport mode, I feel a thunk from the back and when slowing down a few odd shudders. Drove it cautiously a bit more and felt fine, then harder and harder. Felt better, no understeer, seemed ok.
Got home and scanned with Vagcom, got the errors below, cleared DTC and scanned again, same errors.
Address 22: AWD Labels: None
Part No: HW0 5Ha lde x
Component: Tuning
Coding: 0000001
Shop #: WSC 00000 000 00000
VCID: 5AB1BED4953067CEBA7-800F
2 Faults Found:
16347 - Control Module - EEPROM Error
014 - Defective
02248 - Valve for Controlling Clutch Operating Angle (N373)
014 - Defective
I'm reaching out to see if any other MQB platform owners who had DCC/Magride are experiencing suspension errors after upgrading to coilovers while employing a delete kit. Some of us S3 owners have been running into this issue after such an upgrade and using this kit by KW. I can throw a suspension error on demand in my S3 by taking a turn/curve at 40mph+ (highway on/off ramps work perfectly for this). A bumpy road or hard braking can also cause an error to be thrown.
Aside from the error being annoying sounding and looking it also re-enabled traction control. You cannot turn traction control back off until you've power cycled the car. This is a pretty annoying side effect that could also be pretty dangerous under the right circumstances. KW seems to think their kit is operating correctly and that the height sensors are out of range due to lowering the car. Currently there's no way to adjust where the height sensors sit so in my personal opinion this seems like a massive oversight on KWs part and their product is not working correctly.
Add a few codes come up today ... P2187 & P218. Bank 1 & 2 running lean at idle
Haven't been able to find a definite answer..
Replace purge valve?? (P/N?)
MAF??
Fuel filter??
I keep getting engine codes and 265 miles per tank.
my car into VAG COM and since then it hasn't boosted past 4 lbs. it has Revo stg 2, K04, aftermarket side mount, full exhaust and a couple other bolt ons. Before the car was spiking at around 23/24 lbs. after pressure testing the system I found that the turbo inlet pipe was lose, so I tightened it. Still no change. I tried holding the battery terminals together for 10 minutes to reset the ecu and I also tried clearing the codes through a handheld code reader. No codes even come up anyways for this. The car is a 1.8T.
View 4 RepliesThe CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 Replies