I have a 2000 Golf GLS which I tried to replace the shifter solenoids on and since I replaced them it shifts very very incorrectly it almost feels as if it starts in 4th gear and works its way to 1st.
View 2 RepliesThe issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 RepliesI have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 RepliesI'm having some electrical issues with my 04 jetta and have no idea what is wrong. This came up recently after changing the solenoids in my 09A tranny (side note: tranny works now ).
[URL] .....
My03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
I'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
I've been having 2000 Jetta GLS VR6. It has an automatic transmission and lately I've noticed that when I put it into Drive, it starts out in 3rd gear. In other words I've lost 1st and 2nd gear when put in Drive. When I manually put it in 1st gear with the shifter, I have 1st gear and all the way up to Drive. The issue just seems to be while in Drive (D)
I've tried the Automatic Transmission Reset :
[URL]...................
Perhaps I'm not doing it right as I can't seem to see any switch under the Gas pedal, just a round piece of plastic that protrudes an inch. I've even removed that and still see no switch.
I recently changed the bushings and installed SS kit. I don't know if this was the case before, but now while in any gear, i can still move it approx half inch to the right and half inch to the left.
I checked everything and all screws are tight. Could it be that the shifter cables need adjustment?
So i was driving home from work yesterday and out of no where i couldnt get the shifter to get over to 1st or 2nd gear. i had to wiggle it around and push down on the shift knob and it eventually went over. Happened a few more times yesterday and like twice on my way to work today. It feels kind of sticky or something, not really moving as freely as it used to. What could be causing this?
View 6 RepliesOkay, my shifter rod got spun, and now it doesn't want to go into any gears. Just freely kinda swirls, and you can't push down. The guy working on the car wants to pull the shift box down and see what is going on. He thinks the shift cable or selector cable is broke.
View 5 RepliesIt happens when there's side to side movement or any gear change. I've tried spray/grease nothing seems to be working. I've read on other forums people replace everything under the boot only to have it return in a few months. I would really like to have this this squeaking gone. Cars a 2012 GTI
View 13 RepliesI recently noticed a rattling coming from my intake manifold and with little research I discovered it was the intake shifter rod. I ordered the new updated bushings and installed them today and the rod continues to rattle just as bad. My car only has 90k and I am unsure what to do to fix the noise. I am hesitant to order a whole new shifter rod because it could be the manifold itself too worn. I am just curious if there is anything that I may have overlooked or if there is anything I can do.
View 4 RepliesThere is only one DIY i can find that is still alive. I have a megan short shifter. Its already half way in. I just don't have any instructions and i am kind of at a loss as to where i go from here. Does this shifter change the way my reverse gear will be engaged? I mean will i need to pull the trigger up to go in reverse or will i still push down? Does the spring that came with the kit go under the sleeve or above it? Sounds confusing.
View 3 RepliesI have an 01 Jetta, 2.0L, 5 Speed manual transmission.
The issue seems to be that the shifter wont shift the transmission "all the way" into 1st, 3rd, and 5th gear. When I shift into the gears that are forward on the shifter, it will go into gear, but then the shifter (in the car) moves back toward neutral a little. I can drive in 1st no problem, but in 3rd and 5th some weird stuff happens...
While driving, when I shift from second to third I have to keep my hand on the shifter otherwise I get kicked out of gear. Also, when I drive on the highway, I periodically get kicked out of 5th gear if I don't keep my hand on the shifter (usually, when I let off the gas).
Anyway, being that I've fixed many problems on many cars by searching forums and google, I spent the last few days trying to figure out the problem by looking through the forums, but I have yet to find a solution. I tried adjusting the shift linkage using the method described in the dieselgeek video on youtube [URL] ...., but it didn't work. I'm pretty certain it's not the shifter bushings because i have almost no play in the shifter in neutral.
I had someone cycle through the gears while I watched under the hood, and its clear that the cable that controls the forward and back part of the shifting is not pulling back far enough on the counterweight on the transmission. (When shifting into 1st, 3rd, and 5th.) When the shifter puts the tranny into these gears I can still move the counterweight on the tranny further than the shifter will pull in in the same direction.I tried adjusting the linkage to compensate for this, but the cable is as far into the cable end as it will go...
I have my GTi, a week ago I broke an axle. I was then convinced by friends the clutch went out. So I said screw it and bought a Southbend Stage 2 Daily. When I get it I go to install it, then find out I have a Broken half shaft. So after taking the tranny out to install the clutch anyways and everything goes alright for the most part. (250k miles so that's why I never returned new clutch)
SO I get everything together. Tires spins. Car goes all is good.
Clutch is super spongy as I need to bleed it. But my problem is the shifter knob is super sloppy. Feels like is a whole section lower. It's hard to engage second as I have to double tap it in with a good throw. Everything is right on the shift tower. And seems like it clicks right into all the gears. But the physical knob feels super sloppy and out of place. First, third and 5th are all super far up and seems like it double clicks after putting it into gear. Like if there was a gear above. Kinda weird to explain. I've done the home alignment on the tower and nob, but only have a bolt that was 4.71 mm. So the cables should be really close to being aligned right. But I can't grab second at high Rpms.
I also need to do my drain and fill. So would it be a drain and fill and clutch bleeding will fix my sloppy shifter? Before I did everything it was tight. Felt right.