Golf IV / Jetta IV :: Brakes Are Not Firm Despite Being Bleed Multiple Times
May 29, 2015
I am fixing up a Mrk IV Golf. One of problems I am having is that the brakes are not firm despite being bleed multiple times. The brakes work but the pedal does not inspire confidence, and I know there is braking performance being left on the table. The brakes are to large and the car is to small to brake as slow as it does. Are Golfs a cross bleed system? I have be bleeding them like I would on an old American car, which is what I normally work on.
View 2 Replies
Advertisement
So the other day I had someone change lanes and slam on the binders right in front of me which caused me to slam on mine. Luckily no one got hit. Now my brakes feel different. Sometimes the pedal feels nice a firm other times it pushes in 2-3" before starting to brake. The fluid level has not changed in the resevoir and the hydroboost appears to be working fine. The power steering is still operating as before. I have checked the calipers and none are leaking.
My suspect is the master cylinder but was wondering if the symptoms are common with the master cylinder failing? I'm thinking internal o-ring has failed due to the near accident event. I'm going to do power steering flush just because I never have. Is there anything that would display these symptoms that I could check before buying the master cylinder?
View 6 Replies
I'm not too familiar with these trucks, but I've been working on my buddies 1999 e350 ford van.
The other day we were going out kayaking, and the brakes locked up, we were able to drive it home, but it was obvious the brakes were holding the truck back. decided to check it out today, found one front and one rear caliper were sticking, the dual piston calipers only had one working, which I believed to be causing the pads to get pressed together crooked, and caused them to "lock up" or get stuck.
anyways, got the new calipers on and no more sticking, so I bled the brakes started in the front and went all the way to the back, did every caliper. brakes feel firm with the vehicle off, but instantly when the van is started, the pedal goes to the floor. it still stops okay, but the pedal feel is not nearly where it should be.
I got all of the air out of the system, but the abs light is on, and has been for a while. I'm wondering if there is something else that needs to be bled in the abs? someone was telling me about bleeding the abs motor?
View 14 Replies
2003 F150 Super Crew 5.4
When I turn off the ignition, the drivers door lock unlocks or pushes the arm through the door for up to 30-60 seconds over and over again. I would say like 10 times and it is annoying as hell.
Is the only part in the door that controls this the actuator or is there something else that can be doing this?
View 6 Replies
I have a 1999 Ford Explorer Sport 4.0 SOHC.
I change the rotor, calipers, and pads on the front end.
When I went to bleed the brakes I got some fluid, then I got none.
I can hear fluid squishing around up near the master cylinder, but none coming to the caliper.
I see a bleeder screw on the master cylinder.
Before the car came to me the person had, had low fluid, but had brakes. Now the pedal just goes all the way to the floor with no effort.
There are no leaks or broken lines anywhere.
View 14 Replies
While searching here for information on changing the brake fluid, I came across a thread that stated: You need a Lexus scan tool to bleed the brakes properly. I've bled brakes and other cars without having a scan tool. I've never bled the brakes on my 09 ES350.
View 4 Replies
My driver side caliper will not bleed fluid, is it safe to say that the caliper needs replacing.
2000 f 150 4.2 v6 232,000 miles
View 13 Replies
Im driving to waterfest with 3 passengers Will this do any harm to the bags with all the extra weight?
View 10 Replies
So my car has been dropping multiple codes after I scanned her and found all five: p0303, p1128, p0172, p1300, p0301. She is just a simple five speed AEG and has no mods other than a SRI. I already replaced the MAF but that ended up causing more codes and I have checked the vacuum lines to no avail.
View 2 Replies
My 2004 1.8T GTI is having a weird issue. It's had 3 coolant leaks in the past 3 months. Every time I get one leak fixed it goes leak free for a couple weeks, but then a new leak pops up in a new place.
First leak was a cracked coolant bottle. Second was a flange near the bottle on passenger side. The newest leak is on the driver side. Car hasn't ever overheated.
View 3 Replies
I finished installing an auto out of a 1999 beetle into my 2000 golf. I used the beetle TCM now it wont shift out of 3rd. If I manually start in first it will shift up to 3rd but nothing past 3rd. I had it scanned with a generic scanner and these are the codes. P1780, P1783, P0725. I researched the heck out of this and I'm not sure what to do. Do I need to take it and have a vag com hooked up to make sure the ecm and the new tcm are talking? It seems others have had these issues and I thought it might be solenoids but that's not what's coming up.
View 2 Replies
It all started a few months ago.... I started my car, and it started noticeably misfiring, CEL flashing and everything. I scanned it with my vagcom and it came up Cylinder 1 Misfire and Random Multiple misfire. I popped the hood, made sure everything was seated correctly, and shrugged.
Ordered some new wires for it, since it had 80k miles on it with original wires, I figured why not. The misfire didn't come back.
A few weeks later, same thing happened. Misfires, flashing CEL, same codes. I ended up driving it the 5 minutes to work anyways and figured I'd look at it later after I got off.
8 hours later I started it up again, ran like a champ, no CEL on. The problem didn't come up again for 3-4 weeks.
So now, without fail, every month or so, I'll get the same issue. It doesn't matter if it's raining or sunny or cold or warm. But if I let it sit for a few hours, it'll act like it never happened.
Now, I haven't replaced the coil pack yet, simply because it doesn't sound like a coil problem, but I might do it just for the hell of it. New plugs and wires have already been done.
View 1 Replies
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
View 7 Replies
I was driving down the road when my car (02 GTI 12v VR6) suddenly died. I pulled off and tried to restart it. It sounded weird, kind of metallic like maybe the clutch went out. It seemed to be firing, but would not turn over so I stopped trying for fear of damaging something. I thought the timing chain may have come loose, however I didn't hear anything catastrophic like valves breaking so if that's the case then hopefully it only jumped a tooth or two. I scanned it and a bunch of codes came back. I did have the battery out for a while before scanning so I'm not sure if some of the Central Convenience codes are due to that or not.
Here's the full scan:
VAG-COM Version: Release 409.1-S
Chassis Type: 1J - VW G/J/B Mk4
Scan: 01,02,03,08,16,15,17,19,22,35,46,56
[Code] .....
View 5 Replies
I have a 1999.5 Jetta VR6 12v, last week the car would not start. After some tests I determined the coil pack had gone bad. Replaced the Coil with a brand New aftermarket German made coil. Now 1 week later, driving at highway speed CEL came on, started to flash and obviously misfiring again. Ran Codes and now im getting these DTC's:
1)random multiple cylinder misfire detected p0300
2) cylinder 4 misfire detected p0304
3) ignition coil output 3 electric malfunction p1395
4) cylinder 3 misfire detected p0303
has this new coil gone bad already after a week?
New issue?
Plugs were replaced less than a year ago, wires were apparently replaced by previous owner about 2 years ago now. Crank sensor replaced less than a week ago...
View 10 Replies
just picked up this 99 Jetta with about 150,000 miles and while driving all of a sudden i had extreme power loss, shaking and shuddering, and the engine light came on. My code reader found multiple random misfires cylinder 1 and 4 codes P0300, P0301, and P0304.
View 7 Replies
I bought my 2001 Jetty w/2.0 only yesterday. While I was looking under the hood this morning, I noticed there was no fans running while engine was going so I took a trip to local auto parts store. O'Reilly's hooked up my Jetty and told me there was four error codes but they weren't sure what they meant. Here are the codes: P0302, P0301, P1128,and P1580. I have no clue of what these errors mean. I am not familiar with Volkswagen at all and there are no volkswagen dealerships close.
View 3 Replies
So I picked up this 24v vr6 in florida and it has the folowing codes:
p2181 malfunction in cooling system
p0303 misfire in cylinder 3
p0305 misfire in cylinder 5
p0300 random multiple misfires detected
p1570 engine control module disabled
I am thinking the ecu is fried? otherwise why else would that last code pop up. misfire codes im assuming are related to the ecu because theres new COP on each cylinder, newer starter, newer alternator, new spark plugs. Cooling system malfunction im thinking could be the ECT sensor, apparently the water pump was replaced a little while back.
If the ecu is fried can I buy a new one chipped from like APR or do they need the existing ecu and then they modify it?
View 5 Replies
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 Replies
So I've had this code come up and go off multiple times its P0A93 which has to do with the inverter Coolant pump, and all the posts I've read about it here, none of them had an intermittent problem with it. Like it will come on and then I let it sit overnight adn it will go off. When I take the cap off the reservoir there is turbulence in the coolant and I've bled it many times. It came on and shut off 2 times on my drive to New York 3 weeks ago but then didn't come on again until today, almost 2500 miles later. And today when the light came on it listed these 4 codes.
View 9 Replies
The vehicle is a 2004 Jetta MK4 1.8t.
Last thing I had replaced about 2 months ago was the Solenoid valve, the MAF and Solenoid hose. Car ran fine for about a month, and bam...engine light came back on, along with the ASR light. At first it was saying "cat converter" so I researched that, and what a surprise, it spoke about being a $1k piece to replace. NOTHING HAS BEEN CHEAP ON THIS CAR, and I'm losing my mind.
The latest adventure happened today coming back from the gym. Car started jerking (which has been normal since every now and then the ASR light will come on, which I'm told is the traction control light. Causing the car to jerk. Simple fix is pulling over, shutting the car off, and turning it back on. That always clears it, and then I'm back on the road.) but instantly it lost power. It wont shift, but the traction control light didn't come on. I plugged my OBD2 tool up, and came back with these fault codes:
P0420: Catalyst System Efficiency Below Threshold (Bank 1)
P0753: Shift Solenoid "A" Electrical
P2637: Torque Management Feedback Signal A
I'm going to go to these guys tomorrow, but I would just like to get an educated guess on what might be going on, so I don't look like a lost dog while they're figuring out what to do next. These guys seem knowledgeable, but they're missing something since I've been in and out of their shop several times and still getting my traction control light on at random times, and now all 3 of these codes.
Does that Solenoid code have anything to do with the Solenoid valve they put in? I was told that cleaning the throttle body and the cat converter might work. Would those be cheaper options to consider, and see if that works?
I also read that unplugging the alternator and plugging it back in, then cleaning the male and female with electrical cleaner might work. I was told about a month ago that my battery barely passed. Could this be causing any of my issues? I also did a log while I was driving, but all that's showing up is a google map document.
View 7 Replies
