I was check fuses looking to see if taillight bulb was bad. I pulled out a few while the car was running, then there was a beep, and airbag light came on. Tailight fuse was ok, just had a bad bulb. Put in new bulb, everything works fine but airbag light stays on. All fuses are good.
View 3 RepliesI have a 2000 VW Jetta GL. A few weeks ago I noticed my charging light come on followed by abs and airbag lights. Which would mean that the alternator is not charging the battery. However I kept on driving and this light would go off. However when I hit a bump on the road this light goes off meaning that the battery is being charged by the alternator. I recently installed a sound system in the vehicle which worked without problems for a few weeks before I started having this problem. Since then I have changed the alternator, battery and taken out the sound system. I now have a 125 amp alternator instead of a 90 amp alternator. The charge light doesn't come on anymore after startup but the abs, airbag and emergency brake light with a beep is now occurring.
View 3 RepliesMy 2003 vw golf gti mark 4. So first things first I just bought the car and have done quite a bit of googling and troubleshooting and its became frustrating because I am a mechanic so now I've resorted to blogging. The air bag light is on and throwing no codes unless you need a specific obd2 scanner. Also my seat belt warning light does not come on and it does not beep so I'm figuring that someone used that vagcom to turn it off. And then third and finally the ac won't engage and I've checked the common problem 30amp fuse in the engine bay above the battery and nothing. I've read a lot regarding common ac problems so I'm just gonna assume that the ac is not bad.
View 8 RepliesI purchased a 2002 2.0 jetta a couple of months ago and not long after I had it I noticed that the airbag light had come on. I brought it to a garage and had them check it out and they came back with a code that read 01218 side airbag igniter passenger side. When. I asked about getting this fixed they really couldn't say much about what exactly the problem was other then to say that it could be a problem with the whole system...which I don't get as the code only came back for the side airbag igniter. I also went and spoke to the dealer here in town and they wouldn't even speak to me about it unless I let them have the car be seen by one of their mechanics and putting the computer on it to read the code which I had already told them about.
View 6 RepliesI'm looking for the secret to eliminating the airbag light when running an after market wheel. I realize that not everyone agrees with this modification, but could we stick to the subject at hand. I know there are some hubs that come with a premade resistor that you plug in that eliminates the light, and I've read that some people use a 4.7 resistor. I don't have a plug in resistor, I've tried the 4.7 and that didn't work for me. I've never been able to find any place that would sell the plug in resistor separately, is this possible? What I might have done wrong?
[URL]........
Not permanently, but temporarily? I can't really figured out any obvious reason why it is on, all the connections seem good, but I don't really know if I've covered all my bases. I obviously care that it functions properly in the event of a collision, however I was curious if there is a way to manually turn it off for a duration? I have an inspection coming up which doesn't allow for this light to be on.
View 19 RepliesI swapped my cloth seats for leathers today and the airbag light came on after... the seats were out of a 2000 golf, so I was expecting to have to splice wires, but, the connectors were the exact same on the cloth from my car and leathers from the donor car... so I just did a plug and play... I scanned with vcds and got these codes:
Address 15 -------------------------------------------------------
Controller: 1C0 909 605 A
Component: 1M AIRBAG VW51 02 0006
Coding: 12621
Shop #: WSC 00000
2 Faults Found:
00592 - Seat Belt Switch: Right (E25)
30-10 - Open or Short to B+ - Intermittent
01218 - Side Airbag Igniter: Passenger Side (N200)
32-10 - Resistance too High - Intermittent
I take it the passenger seat is the problem... I didn't clear the codes, I wanted to ask here first before I did if I need to do anything to connectors there or just the clear the codes?
I have a 2004 Jetta which has the 2-wire seat belt sensor on the passenger side and a 4-wire sensor for the drivers side. I swapped seats from an older style MKIV which had no seat belt sensor on the passenger side and a 2-wire seat belt sensor on the driver side.
As of now the seat belt sensors are disconnected and I am throwing seat belt sensor codes for both passenger and driver side. I have already tried to clear the codes via VAGcom...took care of 2 ignitor codes, but not these seat belt switch codes.
Is it possible to splice in the 2-wires from the older seats to the correct 2 out of 4 wires coming from my car? What's the difference between the 4-wire and 2-wire connector on the driver side?
Also, reading through the DIY here: [URL] ..... It states that I would need a recoding of the Airbag controller in VAG-COM to deal with the airbag light. What this code is suppose to be?
Last winter I had to replace my front passenger seat. The seat was starting to burn a hole or two, generally getting too hot for the passenger. At about the same time my airbag warning idiot light came on! I changed my front seat. The seat change was no biggy, but I keep getting the airbag light! Can this be cleared simply or only by a dealer?
View 8 RepliesWhile driving on the highway I lowered my seat. Once it got to the lowest setting, I heard something sort of like a snap, and it threw an airbag light, so I raised the seat back up. I'm new to VW, but I know there's lots of possibilities for the light.
2000 Jetta GLS
The remote locks on my 2000 Jetta GLX have been working intermittently for almost a year. I had been using the manual key to lock/unlock until finally the manual lock alarm disarm also became intermittent and I found myself stuck at a truck rest stop at 1:30 a.m. with my alarm repeatedly howling into the night and no way to disarm it. I felt caught. I felt trapped. Like I was found guilty of a crime I had never committed. I knew then - I had work to do.
My research in the forums indicated that the door lock assembly was a common culprit - a gremlin, often leaving headaches as it's only calling card. I worked quick, pulling a driver's side door lock assembly out of 2003 at the local junkyard and replacing it no problem. To my surprise, although this DID fix the manual locking/unlocking/alarm disarming problem, it DID NOT fix the remote unlock problem. The culprit was still at large.
Business as usual with intermittent remote unlocking/locking/trunk-popping for weeks until my dash threw the "AIR BAG FAULT" light. I decided to question a local garage owner who's VAGCOM told me that it was caused by something on the driver's side door. He was busy, but it reset fine and I was on my way. I know now that I should have asked for the code then but I was caught in the beauty of a girl who only nails polish was the grease and dirt of the car she worked under. And about a mile down the road, the light came back on.
Now, the "AIR BAG FAULT" light is on as soon as I start the car. However, the time seems to vary slightly before the Jetta beeps and tells me in faded red letters "AIR BAG FAULT". Sometimes right when I leave my driveway, sometimes not before I drive a mile or two down the road. My remote unlock is still working intermittently.
I need both my airbag fault and the remote unlock fixed. I'm wondering if these two problems are related? Like maybe there's a loose connection that is causing the airbag sensor to short and it's beeping when it bumps out of place and maybe the intermittent remotes are being caused by slamming of my driver's side door too hard & it's losing a connection as well. I tried putting a little conductivity jelly in the female clip that goes to the window regulator motor because I heard that the airbag sensor is in there somewhere but it didn't make a difference.
Driving my car (2001 Jetta Wolfsburg w/ 1.8T) to work yesterday and all of a sudden the airbag light comes on... As I was almost to my exit I continued another 500 yards. The ABS/and brake light come on as well and the car dies as I coast to the side of the road. I would not start so I had my spouse bring the trailer and another battery to see if it would start up. It started up and we loaded onto the trailer.
Took the battery to Napa and they said battery was bad. Today I buy another battery and the voltage of the battery not running is 12.2V and with the car running the alternator to battery voltage is the same. How do I know if the voltage regulator is bad or the diode or something internally in the alternator? Also how to I get the airbag light reset?
My jetta. It is a 2001 2.0. I was wondering how to get the car to "Beep" after you lock the car. The car has never done it since I bought it...The trunk is closed so i know that is not the reason....what are some other reasons that would cause me to lose that friendly beep?
View 7 RepliesI have searched up and down and i can only see people complaining about the reverse of my situation.
Is the Horn and the Alarm beep the same unit? Maybe a fuse?
Any VCDS instructions to reset?
View 2 RepliesSo I have an 05 MK4 GLI, my alarm has not worked since the day I got it. Hold the alarm button on the fob, no luck. when I lock or unlock the car, the lights don't flash and the horn doesn't beep. My ex had an 03 GLS 2.0, alarm/lock/unlock worked without a problem, so why mine doesn't work.
View 7 RepliesEvery time I start my Golf there is a beep, the EPC light and ABS light come on and stay on, and the brake warning light starts flashing and continues to flash.
I have had the fault codes read and it came up with the following:
0414 Control unit improperly coded Faulty
0606 Yaw rate sensor Circuit defective.
What these faults actually mean and what might cause them? I'm quite keen to resolve the issue as anything brakes related makes me nervous, plus I do drive the car hard and use the 4Motion system, which I believe utilises the ABS system?
Probably worth mentioning that the car is fitted with a Series 1 Blue Haldex controller, in case that makes any difference?
Every time I speed up or slow down my ABS, TC and parking brake lights turn on and my car beeps at me. I'm assuming that I have a wheel speed sensor going out. But when I check the codes there is nothing and the check engine light never turns on, so how do you tell which one to replace? Or is my problem something different? I drive a 1999.5 vr6 Jetta.
View 10 RepliesI don't know how to get rid of annoying "Passenger Airbag Off" BEEP. Follow the instructions for removal of head unit.
1. Unplug the electrical connector from the light unit:
2. Disassemble the light unit into its constituent parts. You can pull the display panel off the electronic bit with some modest force, and it'll be obvious how the prism is separated:
Note that I painted the prism surface black with a sharpie. That doesn't work much.
3. Layer a precisely cut piece of thick black paper between the prism and the inside of the panel. Check for a light
leak by holding it up to a bright light. It's tough to cut the paper just right so that there are no light leaks.
4. Reassemble the light unit and stick it back into place.
5. Reseat the head unit.
Warning: you can't just leave the light unplugged. It'll throw an airbag fault. That's why I opted for blocking the light, rather than getting rid of the light altogether.
I have a problem with my vw jetta vr6, the airbag light is always on. I changed the battery and few days later the airbag light came on. I drove my car to the dealer and they found out that my driver airbag unit has a lot of pressure on it, so they told me that the airbag needs to be replaced.
View 5 RepliesRecently I changed a turn signal switch on my VW Jetta 1994, and it turned out the new switch had a faulty horn/airbag connection (just not springin out enough), such that power was not being relayed - I figured this out when the horn would not blow, and on inspection I realized that there was a gap between the connector on the top of the switch and the horn. At the same time I realized that my problem was the signal relay, and not the switch. So I changed back to my old signal switch. The horn is now fine, but I have the airbag alarm light on. I am cannot think of anything I did wrong. So I am wondering whether the light could be coming on because of the initial error when there was no connection where the airbag signal keeps coming on even after the repair error is corrected, or does the alarm indicate a current error rather than a lingering memory of the error I had initially?
View 14 Replies