Golf IV / Jetta IV :: After Installation Of Cold Air Intake Where To Put Breather Hose
Jun 27, 2015
After installing my cai, I couldn't find where to put this breather hose, I'm lost to if I need it and where to put it...
View 2 RepliesAfter installing my cai, I couldn't find where to put this breather hose, I'm lost to if I need it and where to put it...
View 2 RepliesI have a 337 with Injen cai. Well, I have since removed the cai due to the fact that rainwater/water during a car wash will run off the hood and onto the top of the inside of the drivers side fender (under hood) and eventually run down onto the filter itself, thus causing it to become water logged. This of course is not good. My question.. I've tried so many things to no avail.
View 7 RepliesI have a 2002 jetta 1.8t with unitronic stage 2 ECU and following mods:
ssqv BOV with recirc fitting (so acts like a DV)
3 inch open downpipe
Water/Meth injacetion (-35c washer fluid)
Short ram intake+heat sheild.
Spring loaded wastegate.
So for a while now I could hear a very quiet high pitched sound along with a whoosh sound from the intake at low rpm when the car is cold, after 5-10 minutes of driving the sound changes to where i just hear the wooosh from the intake, no high pitched.
I went out, let my car park for about an hour or 2 in 0c temp. went to drive it,everything is fine, the car just hit 90c. so i floored it, but traction control was on and i have winter tires, so it barley got to 4k rpm. CEL started flashing, no throttle control, really annoying high pitched sound from engine bay with lightest touch of throttle. the trubo was boosting to 22 psi and holding up to 16 PSI at redline before this happened.
The car would struggle to stay at idle, massive vibrations. but after reeving to 2k+ rpm no issue staying at that rpm, no blue/black smoke from exhaust. i scanned it and only got misfire codes and this strange code : "17925 - power supply relay for ecu (J271 or J363): electrical malfunction"
I had to clear the codes 3-4 times and restart the car 3 times for the power supply relay code to go away. but all the misfires, the high pitched sound stayed. it would misfire while driving, then stop, and then again.
I also logged with VCDS, and flooring it from 2k rpm to 2.6k rpm resulted in 0 extra boost over idle (idle boost was 980mbar).
Is my turbo blown 100% because of that sound, or could it be something else causing the "dentist drill" sound? And what about the power relay issue for ECU, could this cause any of the symptoms?
I have a CEL. I don't have any special tools or experience but am not afraid to try something.
View 8 RepliesThis hose comes off the top of the air box next to the air intake and goes down towards the front of the engine. I need to know what this hoses called or what the part number is as mine is missing.
View 4 RepliesSo while inspecting my CV grease explosion everywhere (pretty sure I tanked an axle), I noticed my crankcase breather tube was smoking, which I found to be odd. Is that normal? It looked kind of like exhaust...
View 3 RepliesSo I had a hose come apart that is located under the intake manifold on my 1.8t. It's some type of air hose because I can hear and feel the air coming out when the car is running, and it's also making my car run rough and miss, mostly at idle.
View 6 Repliesyesterday my upper radiator hose connector broke off and I replaced it filled it up with coolant and now the upper radiator hose gets really hot at normal temps while the lower hose is cold maybe and gets warm not hot or anything... I see some steam coming off the radiator but i think its all the coolant that splashed on it yesterday from the hose busting off and flooding it basically. the car does not overheat at idle or driving or anything so I am curious to what it could be
View 4 RepliesI just recently installed an intake onto my fiances 09 tiguan and now the esp light is on and the power steering light is on. I have no clue how this impacted, how to get this straightened out. Should I put the airbox on?
View 5 RepliesI recently noticed a rattling coming from my intake manifold and with little research I discovered it was the intake shifter rod. I ordered the new updated bushings and installed them today and the rod continues to rattle just as bad. My car only has 90k and I am unsure what to do to fix the noise. I am hesitant to order a whole new shifter rod because it could be the manifold itself too worn. I am just curious if there is anything that I may have overlooked or if there is anything I can do.
View 4 RepliesI only removed the standard air filter housing and fresh air intake yesterday to get access to the VSS and Speedo drive to change the differential fluid on my 01M transmission. I was surprised to find that there was a fine metal mesh screen installed at the entrance to this air intake tube. This would be located behind the battery and just behind the drivers side headlight is where this metal mesh screen is located. Anyways, this was easily disassembled to clean and reassemble. However, I did not find anything about this mesh screen in my Chilton's manual, but this is now on my annual maintenance list. I added some pic's to show the clogged air tube. There was also a spring loaded door on this air intake tube...
View 5 Replies195,000 miles on a 1.8T I removed the intake hose that connects the inter cooler to the throttle body and noticed a bit of oil inside the hose. I was guessing it may have come from the turbo due to a leaky seal, but this is strictly a guess. The car doesn't consume too much oil (maybe a quart or less between changes). What is the life expectancy for a turbo?
View 2 RepliesHad a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
I have a new hose I need to install because the one on now is cracked... I have pulled the metal clip down, but how do I remove this so I can install the new one? I don't want to break anything else yanking on it too hard.
View 5 RepliesDuring the removal of my hood. I've broken my fluid line for the windshield washer. Not sure how to replace or if this is able to go back in my hood, I've searched and have fallen short to a decent answer.
View 4 RepliesLooking at my circle track car when they told me my air intake temperature sensor was missing this is a picture online I found: [URL] ....
The hole is filled with a bolt and some epoxy. I don't see where the cable is for it. What will this do to my car? It is a track only car.
Upon installing LED interior lights in the dome lighting in my 2003 Jetta GL 5 Speed, my power door locks, power windows, interior lighting, and license plates lights no longer work. I looked at fuse 14 (the fuse associated with interior lighting) and it was not blown. I also tried replacing the LED lights with the lights I had removed while putting in the LEDs, and everything still does not work. Another thing to note is that during installation, the 3 lights in between the drive and passenger seats in the front worked when LEDs were inserted into them. It was not until I replaced the passenger side rear light with an LED that all of these malfunctions started to occur.
View 2 RepliesSo I just bottomed out really hard and I pulled over to a gas station to check out my car to see if I busted anything. I noticed on the way to the gas station that for the first two times I hit the brakes hard there was a clunking noise but now it went away. Onto the leaking part though, there are two hoses that run just along the inside of the frame on the passenger side just behind the wheel and one of the lines is leaking a lot of water. What these lines run to/from? I'm going to get the car on the lift tomorrow.
View 2 RepliesI have coolant leaking from the bottom of this hose on my brothers car. I am not very familiar with the BEW's as I drive an ALH. Just looking for info about part number or name on this hose so I can get a new one. Has a part number MH3364 on it but that is not working anywhere.
View 2 RepliesI am having an issue after my intake install, it was working fine all day and last night i get a light on the dash bored (looks like the one when you take off the esp) and I get this:
code 16485 Mass Air Flow Sensor (G70) Implausible Signal : P0101
Static - No
What could be the cause of this because i ran this intake before no issues I only took it off and put the stock intake back in due to the rain but now since the rain is gone i decided to switch
So I replaced my air filters today and my drivers side intake hose was wet with a brownish oily substance. I looked around for obvious culprit but found none. Looks like there is an aluminum brick there for brakes but it was shinny and clean the shock tower covers had what looked like built up of this substance. Doesn't leak onto the driveway and see no other signs anywhere else.
View 4 Replies