Golf IV / Jetta IV :: ARB Rubbing Drive Shaft After Lowered
Aug 13, 2015
Had the common problem of ARB rubbing the drive shaft after I lowered an extra 15mm - It didn't rub before I went this extra 15mm. I got adjustable drop links on and they also didn't work. I basically told the garage to sort it out and they put standard drop links back on (not genuine) and also new wishbones because I needed them. Got my car back and the rubbing was even worse. So I raised it back up the 15mm, to where it was before the rubbing started, yet it's still rubbing like crazy. I'm wondering if the new wishbones may be causing this because of new bushings or something and it all being tighter. And also what am I supposed to do? I shouldn't have to buy a whiteline ARB because it wasn't rubbing at this ride height before the wishbones and drop links were changed.
To summarize:
>Lowered car extra 15mm, rubbing started
>Drop links and wishbones changed, rubbing is worse
>Raised back to the point where rubbing started and still rubbing just as badly.
View 4 Replies
Advertisement
I have a 2004 GLI that I just completed the slave cylinder on, after i got everything back together my driver side axle is now rubbing really bad on the sway bar where it connects to the endlinks. What could be wrong?
View 2 Replies
Found some cracks in the outside of my driveshaft. 2002 Jetta 1.8T 5-Speed Manual.
Part number: 1J0 407 271 GJ
I'm guessing it's just rust/age. Honestly, I don't even know if this need to be replaced. CV boots are in perfect condition, now cracks or leaks whatsoever.
View 4 Replies
So I was pulling out of the parking lot at work in first gear going about 10mph when I heard a loud clang and lost power to the wheels, I just had the car towed home and its dark out so i haven't gotten a chance to really take a good look.
My question is, how did this happen? the car is lowered on coils. I also Installed a B&M short shiftier about 3 weeks ago, i doubt it but could that have anything to do with this?
View 4 Replies
The cruise worked perfect before I lowered the car and now it works occasionally.. It was on most of the 10 hour drive to this part of Florida and around town it's worked but has started to act up a bit again now.. Sometimes the cruise light will flash and then won't work but other times it's fine any input? The car is an otherwise stock AWP at 107k miles..
View 2 Replies
I was doing some work on my R today and noticed something. On the passenger side front half shaft, at the transmission side, there is a bolt that has worked itself lose that is rubbing against it. I cannot get a bit into the bolt to tighten it back up as is since it is pressed against the shaft.
View 7 Replies
While driving on the highway I lowered my seat. Once it got to the lowest setting, I heard something sort of like a snap, and it threw an airbag light, so I raised the seat back up. I'm new to VW, but I know there's lots of possibilities for the light.
2000 Jetta GLS
View 2 Replies
so my r32 recently started making a nasty popping noise. the sound seems to either be coming from something in the rear end or drive shaft. not sure why it happened. i went on a 2 hour trip. got there parked it. aired it down (bags) but then when i came back and when to drive it again. it all of a sudden it started making a horrible popping noise. i thought it was the front wheel bearing going out since i knew it need to be replaced but i did that today and its still making the noise.
The noise sound just like a RWD car with a welded diff when it turns. kinda has that locked rear end hop popping noise. i lifted the whole car off the ground and put it in first to let the tires spin in the air but of course theres no weight on them so it doesn't make any noise. i'm really stumped on what it could be. im going to take the driveshaft off and see if it still dose it. then i know its for sure in the rear end. What it could be?
View 4 Replies
Car has been making da da da da da noise from the rear for the past week or 2. The noise is consistent with the wheel speed and I can heard it clearly when I am next to barrier or a truck or something the sound will pounce off it. I drop the car off, later they told me the drive shaft is vibrating a lot and it might go.
View 8 Replies
Any good way of getting the spline shaft out of the hub? I got the big axle nut off ok.
Normally the CV then just pulls out (inside unbolted, lower control arms (3 bolts) out). This one not moving if air chisel, 5lb sledge hammer.
NEVER had a rusted one (90% of my cars are Audi, not VW).
Do I have to remove the entire hub (including take the strut out) and put on hydraulic press?
View 6 Replies
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 Replies
I just finished my first MK4 steering rack replacement (don't work on too many VWs), and when I placed the steering shaft from the column onto the shaft from the rack and bolted it down, there was still some clearance (see photo). I was able to get the bolt tightened down ok, but the clearance is bothering me.
View 2 Replies
Recently I've noticed that every time when shifting from park to drive and occasionally from reverse to drive in my 05 Golf GLS, I would have to remain off the gas for 3-4 seconds otherwise the car would jerk forward. If I press on the gas ever so slightly, the rpm would go up to around 1000 then jerk. Why this is happening?
View 2 Replies
I'm trying to get to the manual transmission input shaft seal on my 01 GTI w/12V VR6. I've removed the 3 bolts surrounding the input shaft but the metal shroud underneath the 3 bolts seems to be adhered tightly in place. You can see the 3 bolt holes and metal shroud in this photo: [URL]
Am I on the right track in trying to remove that shroud? If so, how do I loosen it?
View 8 Replies
Have a mk4 GTi vr6 with long beaches with sit at an offset of 38. Honestly the offset thing confuses me quite a bit. I'm running 235/17/45 tires. I had my car lowered before the winter and I can only go so low before it starts rubbing. What size spacers i should go with to basically go as low as possible. If not as low as possible, I love a wide rear end so maybe poking in the rear end and lowered in the front for like a rake effect.
View 5 Replies
Whenever I let off the gas there's a rubbing/knocking noise under the car, the sound will slow down as the car slows down but as soon as i press the gas pedal it starts again, it also doesn't do it if I am stopped and in neutral and rev the engine not sure what this could be?
View 24 Replies
I recently lowered my mk4 golf with coilovers, now the sway bar is rubbing on the right driveshaft axle... could I just get a small diameter driveshaft instead of getting sway bars? My driveshift is about 2 inches wide...
View 24 Replies
I've got an 03 Jetta TDI 5-speed with 210k. I just replaced tie rod ends, ball joints, struts, shocks, springs, and bushings/bearings on the front.
After I took the car off the jack stands, I tried to reverse and the car is held in place pretty firmly. I gave it a bit of gas and it sounded like the brakes were rubbing. The brakes feel a little soft.
I checked the wheel clearance (I didn't lower the car) and everything looks fine. Did I pinch a brake line or something?
View 15 Replies
Im working on my buddies 2005 F150 FX4. In the midst of buttoning everything up and calling it a day I happen to see fluid dripping. The OEM steel brake line had been rubbing on the steering shaft and while doing the brakes, must of busted through all of the way.
I have been to Advance and Napa at least 4 times trying to match stuff up. Nothing works from either of them.
Called Ford and talked to a parts guy who lacked general automotive knowledge and finally had to pull up there diagram to show him the correct part. He told me that part is discontinued and cannot be ordered.
It is #2264 in this diagram.
2005 Ford F-150 Front Brake Hydraulic Hose | FordParts.com
I have the factory fittings and everything to make a new line. I cannot find tube that is 5.20mm or .20". Everything I find in a roll is either 3/16 or 6mm.
The fitting is a 12mmx1.00 on the ABS brain. The caliper hose appears to be a 3/8x24. A 10mmx1.00 which is standard metric 3/16 tube nut is to big for the OEM caliper hose. A standard 3/16 flare wont seat on the caliper hose.
So it seems like what Ford did here was.... a 12mmx1.00 on a 5.20mm tube to a 3/8x24 to a caliper hose that wont seat with out 5.20mm tube.
View 1 Replies
While switching freeways yesterday and shifting down into 3rd before hitting the exit ramp I heard I a slight clunk, and then this continual noise began. I initially wasn't quite sure if it was my car or the sound of the of the large semi engine braking in front of me so I continued on to the freeway and was able to shift back up to 5th and get to speed.
However, I held back to around 60Mph because the noise started to worry me as I continued to hear it after passing the 18 wheeler semi. I got off at the next exit and noticed that the noise ONLY occurs when the car is decelerating. It happens in every gear as well as neutral; having the clutch in or out doesn't make a difference either.
*When accelerating in any gear, even the slightest bit, the noise disappears.
I've scavenged the forums to find a similar issue but to no avail.
I've uploaded a video that shows the issue occurring. The video is taken from the driver's side wheel, but the sound resonates throughout the front of the car, can't really pinpoint where though.
2002 Jetta 1.8t possible transmission noise
[URL] ....
2002 Jetta 1.8t ... 210k Miles
I've recently replaced the Control arms, outer tie rod ends, ball joints, springs, struts, all for rotors/pads, rear calipers, handbrake cables, timing belt (with pulley kit) water pump, etc. full syn Oil changes every 3k-3.5k miles, Premium petrol only.
View 1 Replies
So I've had a low rubbing sound specifically when I'm turning or banking right. I don't want to put much more money into this mk4 because I'm planning on getting a new car in the next 12 months. How do I know which bearing needs replacing?
View 2 Replies
