Golf IV / Jetta IV :: 2007 - Seat Heater Light Does Not Illuminate
Dec 20, 2014
My son has a Jetta MKV and the seat heater button no longer illuminates. I assume there is a bulb in there.
View 1 RepliesMy son has a Jetta MKV and the seat heater button no longer illuminates. I assume there is a bulb in there.
View 1 RepliesIt seems the drivers seat heater only works when turned all the way up. Could the switch be bad, or is there some kind of variable resistor that goes bad? Dunno where to start really.
View 4 RepliesI swapped my cloth seats for leathers today and the airbag light came on after... the seats were out of a 2000 golf, so I was expecting to have to splice wires, but, the connectors were the exact same on the cloth from my car and leathers from the donor car... so I just did a plug and play... I scanned with vcds and got these codes:
Address 15 -------------------------------------------------------
Controller: 1C0 909 605 A
Component: 1M AIRBAG VW51 02 0006
Coding: 12621
Shop #: WSC 00000
2 Faults Found:
00592 - Seat Belt Switch: Right (E25)
30-10 - Open or Short to B+ - Intermittent
01218 - Side Airbag Igniter: Passenger Side (N200)
32-10 - Resistance too High - Intermittent
I take it the passenger seat is the problem... I didn't clear the codes, I wanted to ask here first before I did if I need to do anything to connectors there or just the clear the codes?
I have a 2004 Jetta which has the 2-wire seat belt sensor on the passenger side and a 4-wire sensor for the drivers side. I swapped seats from an older style MKIV which had no seat belt sensor on the passenger side and a 2-wire seat belt sensor on the driver side.
As of now the seat belt sensors are disconnected and I am throwing seat belt sensor codes for both passenger and driver side. I have already tried to clear the codes via VAGcom...took care of 2 ignitor codes, but not these seat belt switch codes.
Is it possible to splice in the 2-wires from the older seats to the correct 2 out of 4 wires coming from my car? What's the difference between the 4-wire and 2-wire connector on the driver side?
Also, reading through the DIY here: [URL] ..... It states that I would need a recoding of the Airbag controller in VAG-COM to deal with the airbag light. What this code is suppose to be?
The little green light on my Parking brake button does not illuminate when i push the button to let me know if its on and I am also getting a message on my dash saying Check Parking brake system and have vehicle checked by a dealer. What my problem could be before I take the vehicle to a dealer? Apparently the automatic parking brake is not working at all and the little green light doesnt light up when the button is pressed. I have a 07 ls460 with 112k
View 3 RepliesMy 2003 vw golf gti mark 4. So first things first I just bought the car and have done quite a bit of googling and troubleshooting and its became frustrating because I am a mechanic so now I've resorted to blogging. The air bag light is on and throwing no codes unless you need a specific obd2 scanner. Also my seat belt warning light does not come on and it does not beep so I'm figuring that someone used that vagcom to turn it off. And then third and finally the ac won't engage and I've checked the common problem 30amp fuse in the engine bay above the battery and nothing. I've read a lot regarding common ac problems so I'm just gonna assume that the ac is not bad.
View 8 RepliesLast winter I had to replace my front passenger seat. The seat was starting to burn a hole or two, generally getting too hot for the passenger. At about the same time my airbag warning idiot light came on! I changed my front seat. The seat change was no biggy, but I keep getting the airbag light! Can this be cleared simply or only by a dealer?
View 8 RepliesI have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 Replies2007 f250 4x4 shift on fly will not work. switch to 4x4 high light will not illuminate and it will not go into 4x4. i have tried in park, in neutral, rolling are stopped. both lights work when you turn ignition key to on.
View 12 RepliesI have an APR stage 2+ R with 70k miles and have been getting strange CELs recently. What is going on. Here is what happens:
1st- a ding a ECS fault displays in mfd.
2nd- a ding and ABS fault lights up
3rd- airbag light and tire pressure lights illuminate
4th- steering wheel light illuminates.
5th- all lights disappear after a few minutes, except the airbag light.
Car drives fine and lights do not illuminate upon restart. The light show appears randomly usually a day or two later.
I have a 2007 Saturn Relay with heated seats. One of the seat heaters has quit working and now the other one gets super hot after it is turned on for a while. What is causing the seat to get super hot? I don't want to burn up anything.
View 4 RepliesWhile driving on the highway I lowered my seat. Once it got to the lowest setting, I heard something sort of like a snap, and it threw an airbag light, so I raised the seat back up. I'm new to VW, but I know there's lots of possibilities for the light.
2000 Jetta GLS
Both front seat heaters are not working on my 2009 Avalon XLS. The center console lights do not illuminate. I presume it's not the fuse because according to the owners manual the 7.5A fuse also controls dash light, power outlet and flashers and they all work. Could it be another fuse, or something else? I can use a voltmeter
View 3 RepliesThe subjects say's it all, is there a DIY for bypassing the heater core? I already search i couldn't find it...
View 3 RepliesJust wondering if RC owners have noticed if the memory setting buttons on the drivers door panel forward of the door lock illuminate in low light conditions. I could swear they were illuminated at one time but now are not..
View 5 RepliesI got a new resistor since my last one was in a puddle of water and installed that today and still have no heater blower motor. I checked all the fuses and have power. I sent power to the blower itself and it spins good. So somewhere between the fuse and the blower it isn't working. I need to take the controls out and test for power there. Didn't have time to do that today. What wires to check or where to start trouble shooting?
View 7 RepliesReplacing a heater control valve for a 2004 Jetta? My car's vents only blow hot, and I checked the cables and saw that the control arm was disconnected. I tried to put the cylinder piece back in and had some luck, but I can't get it to sit tightly in there and it keeps falling out. Also, it still wont change the temperature coming out of the vents. I assume that something broke on the inside piece that the cylinder connected to.
[URL] ......
Here is an example of what mine kind of looks like, but mine is way more loose.
I just replaced my evap box along with most everything connected to it (had some bad servos and replaced other stuff for good measure). AC works great now, but the heater still doesn't work. I've had this car 4 years and the heater has never worked. When I took the box apart, the doors were naked (no foam). Heater core looked ok, but thought it would be stupid not to replace it while I was there.
So, I was hoping this may cure my heater issue, but was really only looking to get the AC going. So, the car had been running for 30-45 minutes and while the heater was on, I went to check the heater core hoses, the pass side hose was hot, the driver's side wasn't. Driver's side goes to axillary pump and bottom of coolant reservoir. Not too long ago, I replaced the mechanical pump and t-stat along with other stuff (crack pipe, etc.). Thought I'd get everything while I had the system drained. Didn't work then, either.
I have a new hose I need to install because the one on now is cracked... I have pulled the metal clip down, but how do I remove this so I can install the new one? I don't want to break anything else yanking on it too hard.
View 5 Replies42dd turboback ... Got it put on today and there is some pretty serious vibration on the driver seat. Why it's doing this? Or does it have to break in a bit
View 4 RepliesMy car had the smell of antifreeze coming from the vents, but it goes away when I use the "recirculating" button. Do u think it's the heater core? I hope not though. Also how much is the coolant suppose to be filled up too? Mine filled up a lot more then half the reservoir.
View 2 Replies