Ok so I started car ran for about 15 min at idle but ran rough a few times then died now wont start. O yea I drove it on sunday and the speedometer and odometer stopped working also.
View 2 RepliesPreviously, I have had no rough starts or other starting issues, and no issues with my battery, which is 4 years old. I left work and had some errands to run--started my car, drove about 1/2 mile. Started my car again, and drove about 1/4 mile. Started my car again, and drove about 2 miles and stopped at a gas station. Started my car again and drove 2.5 miles.
This time, my car started fine, and I began to take off (moving forward--no car in the space in front of me) and after about 5-10 feet my engine died. I haven't been able to start it since. The starter is turning well, but I don't hear anything firing, and giving it gas as I hold the key over does nothing.
Where should I start? I have a video of trying to start, I may try and upload to Dropbox and post. Car is a 2004 Jetta GLS with 247k, and I currently have no DTCs stored (checked using a generic OBDII scanner, not a Vag).
I have a 2003 Golf VR6. Last weekend the car started sputtering and then died. I haven't been able to get it restarted since. I have already replaced the fuel pump relay and the fuel pump. Since I replaced the fuel pump it will prime when I open the door or when I insert the key. When I go to start it it will only stay running for 5-10 seconds then acts like its running out of fuel and dies. EVERY. SINGLE. TIME.
Its not throwing any codes other than a couple 02 sensor codes telling me its running lean. What to do at this point. I was told that vws have a secondary fuel pump relay under the passenger rear seat that sometimes when it goes bad it will turn on the fuel pump to prime it, but wont kick on when its supposed to stay on. I cant find anything on the interweb about it. The shop I took it to that diagnosed the fuel pump said it wasn't throwing any codes when they scanned it.
What happened to my 02 mk4 Jetta after start up and engine failure.
I started the engine, and noticed a high squealing sound just like a loose fan belt, as I backed out my driveway the Battery light came on and engine died, when I tried to re-start the engine it doesn't make any cranking sound just a whirring sound.
2005 Jetta.
I had the AC on and after an hour or so the fan made this dieing noise and crapped out. I shut it off and turned it back on and almost no air came out - even when the AC was not engaged - it just made a weak whining noise.
10 min later I turned it back on and it worked fine, then did the same thing 20 min later. This cycle keeps happening now, what could be causing it? (The compressor is brand new, just had it replaced a week ago, so I don't think it's that).
i have a 05 GTI 1.8T and recently started overheating while driving. for a few months it would overheat if i idled too long but now after driving for 5 minutes it overheats and also wont build any boost. i could hear a hissing sound after i shut the car and thats coming from the flange where the coolant temp sensor is, but is hissing where is mounts to the engine.
update- i replaced the o-ring on the flange, that got rid of the hissing. the no boost must have been due to the engine overheating, but it is still overheating i guess im gonna check the thermostat next.
update 2 - checked thermostat and it is good so I'm at a loss here.
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 RepliesI bought a 2005 camry at an estate sale last week. The serpentine belt was broken and guy running sale said the car set for 4 months and they jumped it off to start and it started and then died and wouldn't start. So I had it towed to my house. changed the water pump, idler tensioner, and new belt and now the car wont start. turns over good. so i changed plugs and still not starting. I will pull one plug in the morning and see if I'm getting spark. If not what would be next step.
View 8 RepliesOn my way to work this morning check engine light came on, diagnosis came up with 2 codes p2181 cooling system and p1516 intake changeover. went to leave work car started then died after about 5 seconds then wouldn't start. as of right now I am thinking that it might be the coolant temp sensor? That's not letting it start? the past week it has been getting bad gas mileage and a low idle.
Mods done giac chip now set at stock setting
APR exhaust and intake
107,xxx miles
I was recently driving home when I made a left hand turn and the car died. I had the timing belt and water pump replaced 1,800 miles ago. It sounds like a timing issue to me. The last time I had timing issue it wouldn't run. This time it runs. Attached is a video of me starting it with the camera looking at the timing belt. The noise I heard made me shut it off. I did not want to cause more damage.
[URL] .....
Driving home on the highway today, not boosting, just regular driving. Car was acting fine, then just shut off. Tried starting, and it would crank, but not actually start.
Got it towed home. Scanned. Two codes: 01314, Engine Control Module. And again, 01314, Engine Control Module. Tried clearing codes, and it says "comm. error". Im using the VAG Check scanner from ECStuning, has always worked fine.
Thought it could be fuel pump, but the fuel pump primes when I open the door. I did notice that the throttle body refuses to align when I put the key in the second position, when it always has before. Radio works, all presets work. Unplugged the battery for a half hour, replugged, nothing. I'm leaving it unplugged overnight to see if that does anything.
Been the proud owner of a '04 Golf for a few years but it hasn't been without its share of hiccups. I recently had my battery die on me. Got the car looked at and apparently the alternator was the culprit, ie, it wasn't functioning and re-charging the battery. Swapped out the OEM for a rebuilt Bosch 120A (my car is a 2.0GL, so it's supposed to be 90a default, but I looked online and saw that I could use the 120). Even put in a new battery as the old one was past its prime. Now the new alternator (which was not fun to install) isn't working either. I had a different mechanic look at it and they said that while the auto shop gave me the right part number, that apparently VWs are hinky with aftermarket parts and I'd have to take it to a VW dealer for a diagnostic? Makes no sense as I've seen tons of people online who've used aftermarket alternators with no problem.
So now the car essentially is dead in the water. Battery light comes on when the car is started and I'm not tempted to not drive the car anywhere out of fear that the new battery will die in mid-traffic. I've checked the grounds, pulley, etc, everything looks fine and connected proper. What could be going on?
I'm running into a brick wall trying to get my GTI to start. This post is my last-ditch effort before just towing it to a shop.
A little over a week ago, the car just died while idling outside a buddy's house. Prior to dying, it had been having some sputtering starts and had been dying while driving as well (engine cut outs) for about a month, but it had always started right back up strong after cutting out.
First I tried replacing the crank position/engine speed sensor. No dice, still not starting. I had new spark plugs in the toolbox so I popped them in, still nothing. Then I realized that my spark plugs were totally dry when I changed them. I pulled the hose off the fuel rail, tried to start the car, no fuel. I had a more mechanically inclined friend come out with a multimeter and he checked my fuel pump and relay. He tells me the relay is good, but the pump must be fried because it's getting power but not pumping (I'm not certain of this as I didn't physically lay eyes on the multimeter when he told me this). The next day, I replaced the fuel pump and the fuel pump relay just to be safe. The car started! I thought I had it all figured out. I drove the car for two days and then, last night, it refused to start again. This morning, pissed off, I went back and was ready to tow it but it started right back up again on the first try. I drove it home, but then later when I went out to go grab a burrito it wouldn't start again. It cranks and cranks but just won't catch.
Pertinent information:
- I do have a CEL. Don't remember the exact code it's throwing but it's something like "Engine distributor circuit, no signal." The code cleared after installing a new fuel pump, but the CEL is back now. Could be a new code, though as I don't have a scanner.
- No other nasty dash indicators are on.
- With the new fuel pump, even when it was working normally, I never heard the usual "priming noise" you get when opening the driver's door. This is strange to me as I used to hear it all the time.
- The car cranks normally but I think it just isn't getting fuel, even with a brand new pump, plugs and relay.
- About a year and a half ago, the coil pack was replaced under the recall campaign.
After all these new parts, I'm thinking electrical. A ground short or something. But I've seen that for some people it was the ignition switch, or the IMMO, or the fuel injectors, etc....
My k03 blew up after 100k miles in a cloud of smoke and oil... Where is a good place to buy a k03 turbo for less than $900 or so?
View 2 RepliesI was driving down the road when my car (02 GTI 12v VR6) suddenly died. I pulled off and tried to restart it. It sounded weird, kind of metallic like maybe the clutch went out. It seemed to be firing, but would not turn over so I stopped trying for fear of damaging something. I thought the timing chain may have come loose, however I didn't hear anything catastrophic like valves breaking so if that's the case then hopefully it only jumped a tooth or two. I scanned it and a bunch of codes came back. I did have the battery out for a while before scanning so I'm not sure if some of the Central Convenience codes are due to that or not.
Here's the full scan:
VAG-COM Version: Release 409.1-S
Chassis Type: 1J - VW G/J/B Mk4
Scan: 01,02,03,08,16,15,17,19,22,35,46,56
[Code] .....
I recently purchased a 01 1.8t GTi with a blown timing belt. I got the car rebuilt, did all maintenance work like brakes , hub/bearings, bushings, oil and all the good stuff that goes into getting the car back up and running. I've finally started driving it and I'm having a weird issue.
Yesterday , I stopped at a red light and the car randomly died on me. Pushed it off the road and checked things out but I couldn't see if there was anything wrong but about 10 minutes later , I was able to restart the car and drive home. Now today , on my way home from work the car starts back firing and I lost all power and rolled to the side of the road where he car would just continue to crank. I was able to get it restarted but it cut out again a couple seconds after. I don't have my code scanner but I know I do have one lean code for something. Maybe cause I have a leak between turbo and dp. I don't have access to vagcom unfortunately..
The other night I was coming home from work in my 1999.5 MKIV 2.0 Golf (Only about a 2 mile drive), once I got to a stop light my car just turned off. No loud bang, no sputter then die, just off (Like I turned the key). After trying to start the car with just a click, pushed it into a nearby parking lot with a friend steering. Once in the park lot we tried bump starting the car (it's a manual) with nothing the car sounding like it wanted to go but never did. The next night I pushed it back to my house, pulled the starter and the battery, and had both of them tested. The starter extended and spun up fine and the battery was in excellent shape.
View 2 RepliesI have an '02 GTI VR6. It died on me on the freeway after surging then limping to a stop and wouldn't restart. I replaced my fuel pump 5 months ago and now I suspect that it has died again, but I want to be absolutely sure that the pump is the problem before I replace it again.
Last time the car would sometimes hesitate in 1st and 2nd for a couple weeks before the pump actually went bad. This time it seemed fine for 5 months then just went out.
The pump does not prime when I open the door. I checked fuse #28 and it's not blown, but there doesn't seem to be any power to it. I tested the power to the fuel pump connector. When I turn the key on I get ~12v for a split second then nothing. While cranking the engine I get ~9v constantly. I hooked a square 9v battery straight to the two outside connectors on the pump and nothing happened.
Can I be sure that the pump is the only problem? Obviously it's dead, but is there any reason for fuse 28 to not be getting power? And should the connector only be getting power for a split second when the ignition is turned on? I tried a different fuel pump relay with no change.
After running at normal temperature for about 10 minutes, my car starts to overheat. I noticed my radiator fan wasn't running at any speed, but my auxiliary fan was running fine. I checked the thermal switch and that was okay, because the auxiliary A/C fan still worked after jumping, and the big fan didn't. I replaced the fan assembly and now both fans work fine, so I assume that my thermostat is okay (maybe not and I'm missing something?). Even though both fans are running, my car still overheats, but maybe after 15 minutes now as opposed to 10. Water pump seems to be fine because I can see it pumping back into the coolant reservoir, and it doesn't seem to be sputtering or anything. Just replaced coolant recently after flushing with water, so I assume that the radiator isn't clogged. I also recently replaced the oil because it needed it anyway. It is still overheating so now I'm stuck. I can get to work and back because it's only a 5 minute trip and it doesn't have time to overheat, but I don't want to keep driving it obviously.
View 9 RepliesI've done as much research as possible, why my Jetta won't start. Here's what happened. I've had the car for 11 months now, put in a new clutch, timing belt, water pump, cool packs, valve cover gaskets, 3" stainless downpipe, and rear springs when I got the car. My rear 02 sensor wire was hanging down below the car, after the downpipe installation. I didn't think much of it until the car died going down my driveway on a rainy day (Had a CEL for a vacuum leak) but right when it died I threw a scanner at it and I got a "no communication with ECM" message.
Cranks but doesn't start and CEL doesn't come back. I did some research and found out that my o2 sensors are in the same circuit or system. Well I found that 2 wires from the rear o2 sensor had shorted out and caused my car to die. I checked the 100 and 428 relays under the hood and they click like normal and seem to be working fine, pulled apart ecm and all looks well and so I reassembled it. The 409 fuse under the dash had just a tiny bit of soot or something covering a few of the prongs so I took the black plastic cap off of it and everything looks ok. Reassembled and reinstalled. Put a new crankshaft position sensor in it. Still nothing. None of the fuses in the side panel are blown either. I'm scratching my head on this one.
Lately I've been hearing a constant click from what seems to be my chains side of the motor. Tensioners and chains were said to be done around 123k. After I've been driving it for a few minutes I hear the click. I thought it was the trans/ throw out berrying but when i push the clutch in and have it in gear i can still hear the click. It is not rapid like a tensioner like a tick tick tick, its like tick......tick......tick, could this be my top end of my block not receiving enough oil? I have a cracked oil pan, doesn't leak that often but i feel as if that is the source of the problem. Also I feel as if i lose power once i hit about 4300-4400 RPMs could that be because of low oil pressure?
View 2 Replies