Golf IV / Jetta IV :: 2004 - Have To Hold The Shifter Until Clutch Is Engaged For 3rd Gear Position
Feb 12, 2016
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
View 1 Replies
Advertisement
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
View 2 Replies
I have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 Replies
99 Jetta, installed a new AC compressor a month ago, has been working great, not clutch will engage for a few moments, then turn off for a minute, then engage again. Seems, like there is Freon in there by the gauge on the low side.
View 4 Replies
Well I read most of the 2011 manual last night to find out why I have "M" on my gearshift, & found it near the end...so we can manually shift our gears. So I normally drive in D, and I use the tow/haul switch when trailing...so under what circumstances does the normal person need to manually shift through 5 gear positions using M, and the 5-position switch?
View 7 Replies
I have my GTi, a week ago I broke an axle. I was then convinced by friends the clutch went out. So I said screw it and bought a Southbend Stage 2 Daily. When I get it I go to install it, then find out I have a Broken half shaft. So after taking the tranny out to install the clutch anyways and everything goes alright for the most part. (250k miles so that's why I never returned new clutch)
SO I get everything together. Tires spins. Car goes all is good.
Clutch is super spongy as I need to bleed it. But my problem is the shifter knob is super sloppy. Feels like is a whole section lower. It's hard to engage second as I have to double tap it in with a good throw. Everything is right on the shift tower. And seems like it clicks right into all the gears. But the physical knob feels super sloppy and out of place. First, third and 5th are all super far up and seems like it double clicks after putting it into gear. Like if there was a gear above. Kinda weird to explain. I've done the home alignment on the tower and nob, but only have a bolt that was 4.71 mm. So the cables should be really close to being aligned right. But I can't grab second at high Rpms.
I also need to do my drain and fill. So would it be a drain and fill and clutch bleeding will fix my sloppy shifter? Before I did everything it was tight. Felt right.
View 2 Replies
06 6.0 fan clutch stuck in engaged position. So I changed the fan clutch it doesn't stay engaged anymore. comes on during startup and gives the appearance that the batteries are dying. Stays on for about 10 minutes when first driving then goes off. If I run ac it comes on at every light and it doesn't matter what engine coolant temp or oil temp and they are all within 6 degrees of each other. I'm thinking maybe the AC is a issue or bad sensor somewhere. No codes everything seems to be functioning. When I say comes on it's on high speed roaring.
View 14 Replies
2002 Saturn L200 Automatic Shifter. Anyway, I can turn the car on fine. I can push the brake and move the shifter fine. But no matter what gear im in park, reverse, neutral, drive, 3, 2, 1 the car still rolls. Also the indicator lights to the left of the shifter are messed up too. When I am in park position, the indicator lights shows I am in reverse. When in reverse it says neutral etc. What the problem is. If i could move the shifter fine why wont it change gears? and how can i fix the indicator lights?
View 19 Replies
The issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 Replies
I have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
View 18 Replies
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
View 10 Replies
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 Replies
My03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.
View 7 Replies
I have a 5 speed 01 wolfsburg. I was about to leave my driveway tonight and went to shift into 1st and the shifter was all loose. I could not shift into any gear, the shifter was just flopping around. Earlier in the day the neutral jiggle was much looser than it usually is, which I thought was peculiar.... So I guess that was it breaking.
Question is: how do I fix it? I looked under the hood and all of the linkage to the transmission looks good, I think it has disconnected/broken under the shift knob... I've looked around online and cant find anything for this year... or replacement parts for that matter.
I guess im going to have to get the car up on jacks and remove the heat shield to get to the bottom side?
View 5 Replies
I'm having an issue with my clutch and I'm really in a hole. Two days ago I was driving my car and everything was fine. Later in the day the shifter got stuck and would not budge out of 5th gear. Eventually it popped out. Driving like normal again and then yesterday I was on my way home from work and all hell broke loose. I was a mile away from my house and the car would not shift into any gear without a fight.
I also at this time lost my clutch pedal. It went really soft but did come back up.. it would not engage however. Limped it the rest of the way home and took a look at it. What I came across was a full brake/clutch reservoir, no leaks around the slave, and I didn't see any leaks around the master. I will say that after the car sat for about 10 mins the pedal felt normal again but quickly went soft after a few pumps.
2.0 AEG 5spd. Trans code DZQ if any of that would be relevant..
View 3 Replies
I have a 2000 Golf GLS which I tried to replace the shifter solenoids on and since I replaced them it shifts very very incorrectly it almost feels as if it starts in 4th gear and works its way to 1st.
View 2 Replies
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
View 5 Replies
OK, here's the update so far.
- new battery
- all fuses fine in panel, all fuses fine on battery pack.
- am getting power to trigger switch upon engine crank (tested w lamp and volt meter).
- did the 'mechanics tap' on the starter motor body
Still no crank when key is turned, instrument panel/gauges light up as normal
So am I right in thinking that I've narrowed the problems down to:
1) bad solenoid
2) bad starter
3) bad connection between battery and starter
or have I missed something?
Also, is there a way to directly test the starter (or indirectly test the solenoid) by applying power to the starter?
View 3 Replies
Here's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
View 9 Replies
I accidentally "popped the clutch" while parking in my driveway and now there's something wrong with the clutch pedal!!
I let the car stall out on accident and somehow had the clutch engaged while in gear and forgot or something and when I released the pedal while still in gear, the car tried to start, but I pushed the clutch in instead of letting it start and now the clutch pedal is all the way to the floor, there is no tension, like a spring came loose, but this is a hydraulic clutch so there wouldn't be a spring, right? What did I do?? And how can I fix it?
2011 Hyundai Sonata GLS
View 17 Replies
My manual 2004 Ford Ranger XLT (4.0L) has been Buzzing/Rattling. (VIDEO LINK BELOW) She has 112k miles on her. Owned 1 month, no issues when I bought from my paps. Its my 1st manual so may have been a little hard on clutch 1st few days. Noise started abruptly 1 week ago when I engaged clutch to shift to 3rd. Its gotten worse over the few days and happens even when in gear. Its much more prominent from outside passenger window. Don't notice for 1st couple mins of driving & is intermittent but often. Noticeably louder when foot is taken off gas in motion. Does not make noise when idling. Generally only above 1500 RPM . Not coming from the back half so I don't think its the exhaust/heatshield
Heres the sound......
View 4 Replies
