Golf IV / Jetta IV :: 2004 - Brake Pedal Seems To Put Pressure Back When Applying Brakes
Apr 4, 2015
So I have a 2004 Jetta 1.8t. Recently I noticed an issue with the brakes. It is a rare occurrence that this issue happens. Maybe 1 out 6 times I slowly stop the brake pedal seems to put pressure back against me applying brake pressure and makes somewhat of a grinding noise and the brakes don't seem to grab as well. But a split second later the brakes return to normal and grab as expected. Could it possibly be air in the brake lines or something totally different?
- Front brakes are in excellent condition.
- Just replaced the driver side front abs sensor and put new rear brakes and rotors on.
View 1 Replies
Advertisement
Im having problems with my brakes mainly being pedal pressure. It's really really soft and has no bite till near the bottom which could be due to the res being low on fluid since both rear calipers seem to be leaking from the handbrake mechanism. When I got my car safetied they fixed my handbrake but I think they put the adjuster to tight cause I felt more rub then what I thought was normal but could be completely wrong. Not to mention this starting happening the day after I got it safetied
the handbrake bracket didn't retract like the other side but since then I loosened the compensator and pulled both side handbrake lines off and retracted the handbrake bracket by hand so now it looks like the right side.
View 5 Replies
I have a 2002 Honda Civic EX 1.7L. Recently the brake pedal would sometimes go to the floor when I'd apply the brakes. The car would still stop, but not as quickly as normally. If I apply the brake and it goes to the floor I would release the pedal and reapply the brake and it would stop at it's normal position and the brakes felt firm and the car would stop fine. I was told my problem was the master cylinder so I bought one on Sunday and replaced it. I bled the lines and it seemed like all the air was out. The brakes worked great and the pedal stopped in the same place and was firm.
Now today on my way to work the pedal went down a little farther than normal during one stop. On the way home it stopped in different places. The brakes would always grab and the pedal felt fairly firm wherever it stopped. I drove it this evening again and the pedal went to the floor like with the old master cylinder. One pump and they grabbed in the normal spot. What is going on? Did I not bleed the lines well enough? Is the new master cylinder just junk? I saw in the manual that air can get trapped in the ABS sensor, but an air bubble problem should just make the pedal squishy, not change where it grabs, right? I'm stumped and I really don't want to take my car in if I can fix it.
View 6 Replies
I just joined as I bought my '97 F-150 5.4 4X4 about 3 months ago. The dealer gave me a 6 month warranty but hasn't honored it at all and I've had one problem after another. That's another story though but right now I'm just trying to fix the important issues. The problem at hand are my brakes.
I was noticing a couple days ago (maybe I never noticed it that much as it was a new vehicle to me) that when I apply the brakes it sounds like a bicycle pump and the pedal travels nearly all the way down. It doesn't hit the firewall but I'd probably guess it has 3 more inches or less until it bottoms out. The hissing only occurs as the pedal travels and stops when the brake pedal isn't moving.
Now I'm not sure if the hissing sound is normal as I replaced the brake booster (from the junkyard though) and the new one still hisses when I apply brakes. The brakes seem to work okay, could be more sensitive it's just the pedal feels soft until it almost bottoms out like I stated before and the the brakes grab a little bit harder. What could it be?
View 2 Replies
2005 F-250 6.0 4x4. After about 50,000 miles on my original brakes, they started to make a squealing noise when applying moderate brake pressure and slowing down around 30mph-0mph. It only happens after Ive driven the truck about 30 mins. It must be warmed up. After 100,000 I decided to change the brakes.....they had plenty of life left on them, but I changed them anyway. I put on new rotors and pads and calipers in the front because one was hanging.
After about 10,000 miles, the exact same squeal has returned. With the windows down, its loud enough to physically hurt your ears if you are next to a car and the sound can bounce back into the cab. It sounds terrible. I thought it was the front brakes, so I took them apart this weekend to put in some Disc Brake Quiet. They pads look great, plenty left, the rotors look great, no grooves. Everything is tight. I relubed pins and brackets and clips. Today...same squeal still. I am at a complete loss here. It is some sort of harmonic squeal and the only thing I can figure is that the rears are the culprit. I have a drivers rear caliper that will hang and stick if you drive it really hard, so I am considering replacing the rear calipers too and do the disc brake quiet treatment there as well. Im not confident this will solve the problem.
Like I said, its so loud you can't drive with the windows down. Its a piercing squeal. Is there anything else that I can check? I can't imagine others don't do this. Its so loud and pronounced that it must be some sort of design flaw or something.
View 14 Replies
My mom's Jetta has had a squishy brake pedal ever since we got it a couple years ago. I figured it went down so far because the brake pads were wearing thin.
After having just replaced the pads and rotors, I flushed the fluid with the Motive power bleeder. I cycled the ABS pump with VCDS, then hooked the power bleeder back up and opened all four corners again until fluid was flowing clean and bubble-free.
Everything went well with the change, but the brake pedal never got as firm as I expected it to. Before the change, the pedal felt like it would get dangerously close to the floor. The brakes always worked, but the pedal hit about 60-70 percent of its travel before the car started slowing down. After the change, it has improved slightly, but it feels like its going about half-way before the brakes start working.
The pedal doesn't drop when you hold pressure on it like I figured it would if the master cylinder was leaking. Is this normal for a mk4 or does it sound like there's something wrong?
Car is a late 2001 2.0 Jetta Automatic with the MK60 ABS pump.
View 1 Replies
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 Replies
2014 Passat... I've got a little over 2,000 miles on mine now and I really do like the car. However, one thing that is really bothersome to me is----the brakes.
I'm not sure if it is specific to my car or to the passat in general. Here's the issue:
When applying the brakes, the pedal feels almost loose, as though the is no pressure on it, but once you push the pedal down far enough the brakes come on heavy, hard and fast. It's like turning on a light switch.
I am wondering if this is an adjustment that I can have done at the dealer to put more feel into the brakes or if this is just something that we all have to live with, of if maybe there could be something wrong with the brakes on my car.
View 4 Replies
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 Replies
Just a heads up to all MKIV GTI owners out there, new and old. If you feel like the tension on your clutch pedal is deteriorating get it checked earlier rather than later. Because if the slave cylinder malfunctions and leaks you will be faced with a big repair bill due to the fact that the slave cylinder is located inside the tranny. Secondly because of this design, which I think is very stupid, it leaks onto the clutch assembly and can get on your clutch plate. At that point you should replace the clutch plate to prevent any further damage that might be caused by slippage. The clutch plate should not come in contact with any fluids or it will compromise the functionality.
View 2 Replies
I took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
View 14 Replies
I have a 2006 Toyota Highlander Hybrid 4WD. Whenever I apply the brake pedal past a certain point, I hear some sort of clunking type of noise from the front of the car. The noise can be done when braking hard, or even if I am at a stop and just press the pedal down hard. It sounds bad but I have not noticed any issues in braking performance. Everything is stock, brake pads have 60-70% as of my last serving. What this is and if I need to be concerned?
View 4 Replies
The brakes surge with more power when the brake pedal is held at a constant pressure. My guess it has to do with the brake booster. But normally a failing booster would result in less braking ability not more.
View 2 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
It feels like I have zero back pressure until I hit about 3500rpm. The car kind of struggles and chugs a bit until it hits the power band and then it takes off like everything is normal...
View 1 Replies
Its a 2007 f150 v6. has 55,000 miles. just got her new tires for Christmas. the truck has doing this for awhile. when you use the brakes the pedal pulsates and the truck jerks back and forth. Feels like bent rotor or something. I've been doing it about a year keeps getting worse. Last year I had the rotors turned and put new pads on got a little better. But not for long continued to get worse again. So I just bought new rotors and pads and still sucks. I thought it could be a bent rim so I just rotated the tires and still no better. Where should i go from here? calipers? something in the front end loose?
View 4 Replies
I have a 05 Ford escape with 107K. When I make a right turn and applying the brakes I feel a clunking in the brake pedal. checked all front brakes and all is ok. So I looked at the drive shaft on the drivers side. I can move or wobble the drive shaft around on the in board CV going in the transmission. Is that normal?
There are no "Clicking" sounds any where while turning which would tell me that is what it is. Also while driving slow not applying brakes there is a lot of clunking and knocking sounds while going over a few little bumps here and there. Is it the inboard CV joint?
View 4 Replies
I just changed all my flex lines to stainless steel and my pads and rotors were replaced. I had some issues with calipers dragging. I used a power bleeder to bleed the brakes all the way around. Now my pedal feels really weird. If I push the pedal fast it brakes hard then it goes to the floor. If i just push it soft, it will just slowly go to the floor without braking at all.
View 3 Replies
One of the high-pressure lines on the back of the rack, close to the exhaust, has rotted out. It was smoking as it leaked right under the exhaust pipe and burned off. The rest of the freshly filled fluid was all over the ground. I crawled under and got a good look at the high pressure line, but where to source these, and if they are even replaceable? I have not tried to remove it yet, but perhaps a shop could bend a new one as a cheap alternative to a new rack. I was also thinking of checking out the pick n pull for a line.
View 2 Replies
This problem just started the other day. I park in a very slightly inclined garage and now when I get into my car in the morning, the brake pedal is so stiff the brakes barely engage and the car will actually roll until the engine turns over. All other braking behavior is completely normal while driving and it only occurs if the car has been sitting overnight. Doesn't seem to happen if it just sits for a few hours.
View 19 Replies
After putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 Replies
