I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 RepliesSo last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
Just a heads up to all MKIV GTI owners out there, new and old. If you feel like the tension on your clutch pedal is deteriorating get it checked earlier rather than later. Because if the slave cylinder malfunctions and leaks you will be faced with a big repair bill due to the fact that the slave cylinder is located inside the tranny. Secondly because of this design, which I think is very stupid, it leaks onto the clutch assembly and can get on your clutch plate. At that point you should replace the clutch plate to prevent any further damage that might be caused by slippage. The clutch plate should not come in contact with any fluids or it will compromise the functionality.
View 2 RepliesI've done a bit of research both here and on other sites. I originally thought that I had a bad flywheel but I'm not convinced. First I'll give a little backstory. I just installed steel shift forks because one broke and got jammed in the gears. None of the gears are damaged and I assumed that when it slammed to halt, the flywheel got messed up. So anyways, the complaint is that when the clutch pedal is released I start to hear a knocking sound which becomes more rapid with RPM. When the pedal is depressed the sound goes away. This sound seems to be coming more from the driver's end of the trans. The car still moves in all gears so I can't imagine that I put it together wrong.
View 6 RepliesIm having problems with my brakes mainly being pedal pressure. It's really really soft and has no bite till near the bottom which could be due to the res being low on fluid since both rear calipers seem to be leaking from the handbrake mechanism. When I got my car safetied they fixed my handbrake but I think they put the adjuster to tight cause I felt more rub then what I thought was normal but could be completely wrong. Not to mention this starting happening the day after I got it safetied
the handbrake bracket didn't retract like the other side but since then I loosened the compensator and pulled both side handbrake lines off and retracted the handbrake bracket by hand so now it looks like the right side.
03 Jetta. The cruise has not been working. Turning cruise on and off works fine as light comes on on dash. Brake pedal switch was replace about a year ago, and I don't think that is the problem because when this was the car would actually go into limp mode.
Just checked the clutch pedal switch by jumping the plug (This was the blue switch lower on the pedal), and still no cruise function. I'm really leaning toward it being the "set" switch/button on the steering wheel as this just feels kinda broken. Did I test the clutch pedal switch correctly? Any other reason the cruise would stop working?
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 RepliesI changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 Replies2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
My mom's Jetta has had a squishy brake pedal ever since we got it a couple years ago. I figured it went down so far because the brake pads were wearing thin.
After having just replaced the pads and rotors, I flushed the fluid with the Motive power bleeder. I cycled the ABS pump with VCDS, then hooked the power bleeder back up and opened all four corners again until fluid was flowing clean and bubble-free.
Everything went well with the change, but the brake pedal never got as firm as I expected it to. Before the change, the pedal felt like it would get dangerously close to the floor. The brakes always worked, but the pedal hit about 60-70 percent of its travel before the car started slowing down. After the change, it has improved slightly, but it feels like its going about half-way before the brakes start working.
The pedal doesn't drop when you hold pressure on it like I figured it would if the master cylinder was leaking. Is this normal for a mk4 or does it sound like there's something wrong?
Car is a late 2001 2.0 Jetta Automatic with the MK60 ABS pump.
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 RepliesSo I have a 2004 Jetta 1.8t. Recently I noticed an issue with the brakes. It is a rare occurrence that this issue happens. Maybe 1 out 6 times I slowly stop the brake pedal seems to put pressure back against me applying brake pressure and makes somewhat of a grinding noise and the brakes don't seem to grab as well. But a split second later the brakes return to normal and grab as expected. Could it possibly be air in the brake lines or something totally different?
- Front brakes are in excellent condition.
- Just replaced the driver side front abs sensor and put new rear brakes and rotors on.
I have a 2002 Celica GTS with 80,000 miles. The clutch pedal pressure was very stiff. I had a 2001 GT, and it had a very soft and easy clutch. I just removed and rebuilt the clutch slave cylinder, using the CSK 2426 rebuild kit. The slave cylinders on 2000 to 2005 Celicas are all the same. After bleeding the cylinder, the pedal pressure is very much improved. It still takes some effort, but not like before.
View 1 RepliesI just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 RepliesI have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 RepliesSo this has happened a few times pedal drops with no back pressure then give a bit pull it back up by hand and it's fine has happened 4 or so times in the last year. I'm reluctant to replace slave and master cylinders could it be anything else? 87 Ford F-150 hydraulic clutch
View 10 RepliesI have a 1995 F150 with the 4.9L and it has 73000 miles on it. One morning recently (it was about 35 degrees outside) I went to start my truck to let it warm up. When I let off of the clutch it stayed on the floor. I shut it off and drove my car to work instead. I asked around at work and one guy mentioned that it was probably my clutch master cylinder...so that day we replaced it, and bled it until it felt like knew. Since then, we have had to bleed it three more times, because the pedal keeps losing its pressure making it harder to shift. I have inspected around the clutch line and the bellhousing for signs of needing to replace my slave cylinder, but everything looks fine.
View 8 RepliesI have a 2003 golf gti 1.8th awp with 160k miles. I was due for a change so I grab castrol edge 0w40 the euro formula like I normally do but the stp filter was on sale with it so i used that. a week later the low oil pressure light comes on when the cars fully warmed up but only at idle I can review it above 1000 and it'll go away. I decided to change the pressure sensor sense it's cheap and easy nothing. I also went to a Bosch filter which I had before same thing light comes on only at idle.
So I decided to drop the pan and clean the pick up there was some crap in it wasn't to over clogged. I did little notice plastic piece surgery in the pan but when I first got the car the dipstick was deteriorating and I know a few little prices fell in there. Also noticing a fairly clean looking motor and oil pump so I don't think sludge is a issue. Anyway I decided to try mobile 1 0w40 euro formula and I read k&ns 3001 filter is a good oversized filter. Anyway light still comes on only at idle, what next?
Addition info the the car it's a stage 2 apr tune with euros ports pcv hoses turbo inlet pipe 42dd's catless exhaust recently had a leak in radiator so replaced that and the fuel pump went out within the last month or two
I got a 2003 GTI 1.8t and the AC air is blowing warm. With the car on, AC on and fans full blast both rad fans turn on but compressor clutch does not engage. Took it to a shop and the mechanic said the system was full of refrigerant but that the compressor was not getting the proper signal and there was an electrical problem.
I check the power at the compressor and it is reading about 7 volts, which is low correct? That should be getting 12-13 volts correct? I also check the pressure switch over by the passenger side and it was getting 13v. What to check next to start ruling out causes? Any quick way to determine whether this is electrical or a compressor issue? I am limited in my abilities as far as electrical work goes.
noticing a few issues with my 2003 jetta 2.0 when driving/shifting....so first main thing I noticed is when shifting from 1st to 2nd gear often times it will make a grinding sound and not shift smoothly from 1st to 2nd....you have to do it real slow/gingerly ...if I short shift from neutral to 2nd its fine or if down shifting to 2nd its fine...I have changed the gear oil...other sounds idk if its my tranny or engine but if going up hill and you throw into 3rd and not going fast enough its makes a rattling sound and is sluggish I know its a old car 177,000 miles so idk just curious if this is a sign of problems?....Last thing after driving and getting home and putting into reverse gear to park it makes a noise like a chugging sound when reversing and can be finicky going into reverse.
View 1 Replies