Golf IV / Jetta IV :: 2002 - Exhaust Leak Coming From Either Manifold Or Flex Pipe
Mar 29, 2015
So I did the seafoam trick and I came to the conculsion that my exhaust leak is coming from either the manifold or the flex pipe. There was no smoke coming from under the car only a mist of smoking coming up from the back of the engine, probably by the manifold or the flex pipe. I do not see any visible cracking per say. I have attached a picture of the end of the flex pipe and it almost looks like someone may have tried to seal it before? I don't know if that is normal or not as seen in the picture.
2002 Volkswagen Golf 2.0 ...
View 3 Replies
Advertisement
I have a 2004 1.8t Jetta with a rusted out flex pipe. The leak is causing a bad smell and also a lot of noise -- What's my best option to replace the downpipe (but also other parts if need be) without having to weld it?
View 6 Replies
I installed the non-resonated exhaust, but I noticed that some air/water condensation is coming out of the small pipe that join the cat and non resonated part of the exhaust.
I double checked the position of the small part and is very deep inside the other tubes, plus I checked the clamps too.
View 8 Replies
Finally got the car started after over a year of acquiring parts and labor. Cylinder 5&6 had misfires due to faulty injector harnesses. That issue has resolved. But I am getting a pretty distinct exhaust leak noise coming from the manifold area and i cannot figure out where it is coming from. We smoke tested it and still can't find the leak.
Things we checked:
-Head to manifold (all nuts tight)
-Manifold to turbo (all nuts tight)
-Turbo to downpipe (2 vbands both tight)
-Wastegate (2bolt manifold to adapter tight and vband adapter to wastgate tight)
-(2) O2 sensor plugs on the maniold (tight)
-All turbo hardware (tight)
-manifold and downpipe have no cracks
Picture:
Video:
[URL] .....
View 9 Replies
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
View 14 Replies
How to replace this bad flex pipe....
View 25 Replies
I have a 2011 F350 CC long box 4x4, with a 6.2, 93,000 km on it. I periodically get a P0420. I clear it and sometimes it comes back in 10 or 20 KM and sometimes it comes back in a couple hundred km. Been doing this for about 800 KM.
Yesterday I got an exaust leak at the joint where the exaust manifold meets the pipe beside the engine. Checked close, bolts appear intact, leak is on the outboard side blowing towards the frame. Looks like a gasket or donut seal failed.
I am wondering if the catalytic converter was plugged or restrictive, would this cause the P0420 and could back pressure from a restricted catalyitic converter cause the gasket to blow?
View 5 Replies
So the flexpipe on my exhaust is cracked and completely broken, so my passat sounds like a Mack truck. I've been looking into getting it fixed and I've been told i need to buy an entire new down pipe. Should i attempt to just get it fixed or buy a new down pipe.
View 4 Replies
I have a question regarding a leak i have in the manifold of my toyota camry 2002 2.4 cylinder. the engine check light is coming up and after a check on the mechanic there is a leak in the manifold where the catalytic converter is attached. when you put your hands near the pipe, you can feel air coming out. See the image attached.
The link is in the part mark as X. The catalytic converter is the one which is circled. [URL] ....
View 9 Replies
Recently, my car has been sounding louder than usual. It seems to be coming from under the vehicle, and when I checked, there was smoke coming from a pipe underneath. My best guess is that the exhaust is leaking. It kind of looks like there's a disconnect here....
View 3 Replies
i have a 2002 250 with the 7.3. i put a mbrp aluminized 4in turbo back with a FTE 30in resonator. I'm getting a lot of noise in the cab sounds like its where the turbo goes into the 4in pipe. the muffler guy said its because of the bigger pipe and not a leak. is there anything i can do to get rid of the excess noise.
View 8 Replies
Have to do a replacement and if so.. is removed the intake the only way to get at those stubs on the ex manifolds.
I thought it was the flex-pipe.. but after listening to the sound and getting an engine code for b1 s1 the leak has to be before the o2 senor for it to pop a code..
It sounds like a standard header leak from backing out bolts or a faulty gasket leak..
View 4 Replies
I have a leak between the turbo and the exhaust manifold. The golden clamp (c-clamp? v-clamp?) broke, and now there is a gap between the two. The dealership doesnt cover it under powertrain warranty (my car has passed regular warranty) but worst of all they do not sell the clamp on its own.
I posted a link to a picture below, it isn't my turbo.
[URL] .....
View 1 Replies
Putting a straight pipe from the cat back on 1.8T mk4? I was thinking going 2.5 inches from the cat back with a tip. But I wanna know how loud it is.
View 6 Replies
I have a 2001 Jetta 2.0L standard transmission I believe my exhaust manifold is cracked looking for a replacement. There is a local guy selling one off a 2001 golf wondering if that would work on my car..
View 1 Replies
Actually developed a crack and subsequent leak in a pipe running lengthwise, so assume the factory weld over the years went bad. Since it would be a weld overhead, wonder what method would be best? Would oxy acetylene work or mig? I don't have a tig so that not an option for me.
View 2 Replies
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 Replies
My truck just started running really loud when it's cold and the leak goes away when it warms up to operating temperature.I did a little bit of investigating and I have found where the leak is coming from at the end of the exhaust manifold where the donut gasket meets the catalytic converters. It appears that the bolts rotted that hold the system together at the gasket. What should I do to repair this? I don't really want to replace the whole manifold because I know I'll break a stud off in the engine because everything is pretty rusty down there. I even took some pictures of the problem....
View 3 Replies
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
View 14 Replies
On the manifold there is a metal/steel pipe that the heater hose hooks to. That pipe is leaking anitifreeze. It has a small hole in it. Is this pipe replaceable or is it part of the manifold.
View 19 Replies
