Golf IV / Jetta IV :: 2001 VR6 GLX Cranks But Will Not Fire
May 1, 2013
To start I was driving home the other night, car just stalled out and would not start back up, at all. Just cranks over and over. Things I have checked
- I am getting a spark from the plugs
- Fuel pump primes when key is turned on
- Fuel comes out of lines, even more so when key is switched over so pressure should be ok, I have not checked exact pressure due to not having a gauge.
- I have checked all relays under the steering wheel (just visual) some had brownish on the connectors and I cleaned all that off.
- All fuses are good and not blown (voltage meter also showed power coming to a few key fuses I checked.
I am down to a few things that I have read could be possible causes
- Camshaft Position Sensor
- Crankshaft Position Sensor
- Not sure what else to really check
View 24 Replies
Advertisement
The car died randomly and now it won't fire. I know it is getting fuel, none of the relays or fuses are bad. I am pretty sure it is not getting spark. The spark plugs that were in it were pretty much gone, put some brand new ones in and while testing I didn't see it spark. The wire resistance tested fine with my multimeter. I just checked the resistance on the coil pack. High side (set to 200k ohms) was ~15.6 on either bank, low side was 0.060-0.062 (set to 2k ohms, my meter doesn't go lower).
View 2 Replies
I have a 2001 mustang convertible in good cond. A 6cly that I have had very little trouble with over the past year. I put in a new battery then, just after I bought it from a dealer. The dealer had gone over it with fluids etc. and I had a friend look it over when I bought it. He said it was very clean and a good buy. So, last week I started having trouble starting it in the morning. It would crank but would not fire. I turned the key off, and then tried again, Same result, cranks but doesn't start. I turned it off again and being worried about draining the battery, I turned everything off, radio, heat and fan, lights. Then I tried to start it again and, it started. I'm thinking I need new plugs, but I ignored the problem and went to work.
A couple days later I was leaving the grocery store, turned the key and same thing again, cranks but doesn't fire. I knew what to do. Turned off everything and tried it again, it started. Ok, so now some repair, possible plugs, is on my priority list. I need to get this fixed before the bad winter weather comes. Yesterday, after a long day at work, I was ready to go home and I it happened again. This time it's terminal. No matter what I did I couldn't get it to fire. This morning it's sitting in the office parking lot and I need to deal with this today.
Could be plugs, could be the fuel pump. Before I call the dealer and pay 4x what I should for this, what do you think it could be? 3.8 6cly. The car is sitting on a slight incline, in the parking lot. Gravity pulls fuel from the engine to the gas tank, if a fuel pump is going bad this could be why I can't get it to start. I'm going to roll it to a level area and hit it with starting fluid to determine if the pump is bad. I'll also pull a couple plugs.
View 18 Replies
Here is what happened. Pulled into gas station and car just died. Tried to restart and no fire. Cranks but no fire. Flat bed trip home and started to diagnose. Thought it was a bad fuel pump so I pulled and tested with a direct power and functions fine. Checked all fuses and relays, all seemed fine. checked for power at pump and nothing. Reset cut off switch and still nothing. Thought maybe ECM relay in the under hood fuse box was bad I borrowed the one out of a friends car. Nothing. Thinking ECM was bad put theirs in my car and got power to pump. So I put their car back together thinking mine was the ECM, then theirs won't start. The ECM relay i took from there car and put in mine blew when i tried to start my car. Got another ECM for my car and put in. Still no power at the pump. Here is the info about the car. 2001 Santa fe 2.4L auto. 80,000 miles. Timing belt, tensioner and all Idler wheels changed along with water pump at 71,000 miles. This car has been very reliable up till this point. No check engine light came on at any time..
View 8 Replies
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
View 5 Replies
2000 1.8t 5 speed Jetta ... The car has run fine up until recently when I started having some starting issues. It was intermittent, and got more frequent and longer. The car will crank but not fire. In the beginning, I could crank it for a few seconds, turn off and turn back on and then it would fire like nothing happen. This continued to happen and progressively get worse until I could not get it started, I could smell fuel which lead me to assume I had to spark.
Today I went out to swap crank sensors but only tried for a little while and cant really get my hand up there. So, I disconnected the battery for a while, went back and connected it, and it started. Up until this point I have had the same 2 codes, over/under boost, but the car has always ran with them present. I scanned today and got a p1545 Throttle position sensor code...But only got that one time. Ive been messing around with disconnecting and reconnecting the battery and among one of these times, the EPC light came on and would not rev passed 1k rpm. turned it off, turned it on, and it was fine after that.
Im sure I have a sensor about to let go Im just not too sure which one it is. I dont have vcds and am not getting a low signal code from the crank sensor with the scanner I have.
View 8 Replies
I have Golf MK4 variant 1.6 77kw BCB 2005y
When i crank engine i hear it fire immediately for a fraction of a second, then it carries cranking empty few turns and then fires again.
Happens only on a first start after standing still few hours.
[URL] ....
View 5 Replies
a 2004 passat 1.8t 5spd came to the shop, cranks but does not
fire/run..i through the vas 5051 on there - p0688 - open circ. main relay...located this power supply relay and tested it - she had an open winding...replaced it runs excellent
View 1 Replies
2003 1.8t gti ... Today when I got in my car...it fired up perfectly normal but when I got in it from leaving school it took 5min to fire up. The engine turned over but wouldn't fire all the time as if the spark plugs were bad. So I bought new NGK spark plugs and had the same issue just a little bit ago.
I know the obvious thing would be to change the ignition coils but they're out of stock everywhere so I have to have them shipped. My question is is the ignition coils the problem? They looked a bit worn but nothing serious.
View 10 Replies
1999 Passat turbo with a little over 100K miles. Car ran fine last night. This morning, the engine/starter cranks well, but no fire. And it has gas in the tank.
View 1 Replies
After running to operating temp, if the car is turned off then restarted (like you would at a gas station, which is where I notice this) the engine will turn and turn and turn but not fire. I have noticed that stomping on the acceleration will cough it into life during this procedure. This doesn't happen every time and I have recently run high octane gas during a long distance trip.
106K miles...
Recent p0441 fault codes and gas cap warning light...
No other problems or codes...
View 4 Replies
I have a stock 1994 Celica GT with the 5sfe M/T .... I do have a headgasket leaking, and I am having another motor rebuilt and put in next month. I just need to nurse this one along for now. Right now it cranks but will not start. does not even fire up at all.
Code 12 - so I got another dizzy from the salvage yard, the pickup coils ohm out like they should as does the ignition coil. and I bought a brand new condenser for it as the old one tested bad. and when I first got the dizzy i put it in and it fired right up and ran for a couple days, then began doing it again. I went back to the salvage yard and grabbed another one that tested good, and when I put it in it fired up the first time but then shut off and has not started since.
But is it possible for the distributor to still be the problem even though the coils test ok? the shaft doesn't have any play in it, and the air gaps are within spec. I can barely get a .2mm between them. I also grabbed a couple of igniters while I was there. When I get it to run it may die when its cold and give me a code 14.
So from there I'm down to testing the distributor circuit, and the starter signal circuit, and the ECU. What is the best way to go about testing this to be Certain of what I need to go buy instead of just replacing stuff.
View 3 Replies
I have been checking on the automotive forums for Suburban no start problems and have tried some of the solutions, but my vehicle still doesn't start. Here is where I'm at: I have spark, fuel pressure at the throttle body, the fuel pump in the tank is working, new cap, rotor, coil, module, fuel filter, and ECM.
I just ran the truck 2 days ago for 10 minutes to flush the radiator, turned it off to install a new t/stat, then it wouldn't start again. I have tried starting fluid, gasoline, it cranks but no fire, not even a sputter. The pump has been replaced probably 9 years ago. The only other thing not replaced is the pickup coil in the distributor, although the distributor was rebuilt about 10 to 12 years ago. This vehicle just sits until needed, can't afford to drive it daily. The truck is a 1987 Suburban 1/2 ton 350K engine, automatic, 4wd.
View 2 Replies
Ok.... So I took my car for a drive to see my friend, started normally....... After an hour or so I left and this time the car cranks but will not fire........ This same problem happened in the dead of winter...... So I remove the key and let the car sit for 15 minutes and then boom it starts as it normally would.........
View 1 Replies
96 sebring 2.5l v6 non-convertibleRan terribly for 12 blocks when I bought it, then died and wouldn't start.Bought it because friend said that mechanic had told him it just needed the head gasket changedReplaced the head gasket then it would crank but not start
checked, getting spark and compression on all 6 cylindersreplaced:-ecm-crank position sensor-combination distributor/camshaft position sensor/coil-flushed fuel system and replaced gas. checked everywhere for possibly misconnected wires and possible misconnected vacuum tubes, they are all triple checked ok. Checked the timing about a dozen times. Checked for misaligned timing sprockets, all ok, no sheared keyways, valves open and close at appropriate times / correct order and crankshaft timing mark matches cyl 1 position.
Fuel pressure is great.Turns over but doesn't fire at all.
View 1 Replies
About a month ago my 2002 accent started intermittently turning on. The car cranks nice and strong when it doesn't start-(until the battery loses too much power from repeated cranking). When it does start, it happens instantaneous, no issues no hard start.
I have talked to multiple people with varying amounts of automotive experience, who have given many things to try.
Things I've replaced or tested, hoping they were an issue:
-Starter and relay
-Fuel pump and filter, as well as relay for pump.
-Battery, post connectors and wires to starter
-Alternator and belt
-Multimeter tested fuel injectors and ran fuel system cleaner for last 3 fill ups
-Replaced spark plugs and wires
-Ran fuel line antifreeze every 2 tanks or so
Things I've been told might contribute to the intermittent starting, but haven't looked into
-Inconsistent fuel pressure
-water in the fuel tank
-Bad ignition switch
-MAF sensor
I live in area, currently in the icy grip of winter. I thought the cold would be a huge contributing factor, but alas, when the car has fired up the temperature has ranged from 1 to -32 degrees and has no issues starting in the deep cold.
View 9 Replies
Having an issue with my 2007 Santa Fe 3.3L. When the engine is cold, been sitting for a few hours not when the temp outside is cold, it takes about 5 to 8 cranks before the engine will fire. I can then shut it off immediately and start it again and it will fire right up.
I currently have the P0464, P0463 and P2068 check engine error codes for the fuel level sensor units. I don't really know if these are directly related as I've had them for about 6 months and the starting issue has just shown up the last month or so. Plus, I would assume these should only be related to sending fuel level information to the fuel gauge. Either way, I'm still leaning toward a fuel delivery issue since it only has a hard time starting when the car has been sitting for a few hours. I don't know if maybe it's the fuel pump or a electrical component. If it's the fuel pump, I'd like to do that when I take care of the sending units so I don't have to go back in. I've tried turning the car to the 'on" position for about 10 seconds without starting it to see if I could get the pump to load the line, if that's the issue, but it doesn't seem to make a difference.
The battery is good. It tested 12.5v after sitting over night.
View 9 Replies
My hyundai accent 2004 standard doesn't start. The engine crank, but there's no fire. I change the camshaft and crankshaft sensor. Also change my timing belt, my alternator, my starter, my control box and my computer. But if I pull the car with my pickup, it runs. While the engine is running, the computer doesn't give me any diagnostic code. I also check my fuse, relay,... Even jump start the starter to check if it was the switch.
View 4 Replies
Have starting problems some times, cranks over real good but will not fire . When this happens i have no fuel pres. But after it starts then it will run good This problem usually happens first thing in the morning. Is there a fuel pump relay in this system or do i have a bad pump . I only have 85,000 miles on this truck.
View 6 Replies
About a month ago I went to start my car and it started up and died and now it won't start at all. All it does is crank and crank and crank. My vagcom say j271 relay open circuit . so I replaced the 428 relay and it still doesn't start. I'm also not getting any epc or cel light with the key in the on position which is strange to me. But if I swap the 428 relay with the 100 relay right next to it I get all the dash lights like I'm suppose to but as soon as I try to start it the two lights go out and won't come back on until I pull the relay out and put it back in. I hate obd2 so much sometimes.
View 2 Replies
So I am not getting spark. Changed crank sensor and cam sensor still nuthing. I am getting no power to fuse 28 and 34. Also I am getting voltage on coil harness on pins 1 and 2 getting about 11.8 and on 2 and 4 getting 1.2. I am starting to think bad ecu?
View 3 Replies
