2001 VR6 owner. I'm looking at a Jetta currently that I suspect has a trans problem. Current Owner was bounced around shops being told it was a timing chain issue causing it to rev around 50-55 mph. Now I know that is definitely not it.
View 3 RepliesMy 2001 1.8T Jetta doesn't want to shift into 4th (slips in and out) when the operating temp gets to normal value. It looks like I will need a full overhaul. Of course the overhaul price is worth more than than car is worth. I may be able to get a tranny from an 03 Jetta with a 2.0 in it. I think it bolt on but are there any other issues? According to this site the ratios are similar -not sure what R&P is.
[URL] ....
I will be getting a tranny shop to do the work. Is this something that is doable?
I have a 2002 Elantra GLS with the 4 speed auto and in the mornings or after sitting in lot at work for 9 hours, the trans shifts hard from second to third (almost as if it has a shift kit) and slips a little from third to fourth. The TPS was changed once and that seemed to eliminate problems at the 26K mark. I have 109K on it now and at around 80k took it in to the dealer with the receipt for the same complaint and what was done the first time. Dealer kept overnight and said there were no problems. I do know from having a performance TH350 built that the harder a trans shifts (up to a point) the longer it will last due to less friction on clutches and bands.
View 6 RepliesIf I press the gas a little hard in drive, my tires squeal but if I'm in reverse I can feel a slipping in the trans. If I try to back a trailer up an inclined driveway, it won't go, the trans slips. I have no crud in the pan. I've replaced the reverse boost valve. I installed a Trans-Go kit which is suppose to eliminate the reverse slip but it hasn't worked. Everything else works just fine and my fluid is red. I have engine braking in 2nd and 1st. The van backs up fine, it just does this in reverse under load.
View 2 RepliesPO730 and P0740 codes at the same time auto transmission slips in 4th gear really bad but not all the time...
View 1 RepliesI've noticed lately that my Mk4 Jetta isn't accelerating the way it used to. It's an '03 5-speed 2.0L, and while the engine idles more or less normally as far as I can tell, when the car is in gear and I press the accelerator, it shudders and "slips", like an an automatic with a bad transmission.
I've checked things out with my OBD2 reader and it's not reporting any codes, no trouble indicator lights, etc., but it's definitely not responding the way it should. I just had it in for a tune-up recently, thinking it was an engine problem, but I don't think that fixed it.
Truck has 222000 miles on it. With gentle acceleration not noticeable, with maybe half throttle rpms increase for say one second or two and then shifts smoothly into third, However at full throttle with the shift coming at 55 mph or so, it shifts perfectly with no slip. It also acts the same manually. I had asked my mechanic about changing the fluid and if it could fix the problem, he said, "well it could work or hurt it." After thinking about it, we decided to change the fluid. He did a full flush and cleaned out the pan which had lots of sludge in it but no pieces of metal in it that would seem to indicate a major internal problem. It doesn't seem to have made it much worse if at all, but did not fix it.
View 1 RepliesI just picked up a 2000 v6 passat with an automatic trans. I am new to passats, esp with autos. The cars transmission is having problems shifting with the trans gets hot (25-30 min run time) and slips. What is the trans code for this car and is it FWD or AWD? It has 220k, and the engine runs great. It was sorta an impulse buy, I plan on flipping it so hopefully tis a good investment. Any common things I should be aware of so I can get it tip top shape to sell it?
View 3 RepliesMy wifes 04 explorer 4.0 4x4 slips in between second and third gear and you cannot manually shift the gearshift below 3rd gear. I assumed tranny was going out but was told that it could be the transmission control solenoid or the transmission control switch (i think they are the same thing). I read that the most common symptom of this going bad is a slip between second and third gear. Haven't checked codes but will when i get home to see what it comes up with. This is the messed up model where you have to add fluid underneath through the drain plug. Was going to change fluid and add lucas to it to see if it remedies the problem.
View 1 Replies2006 f150 4x4 4R75E trans slipping in forward gears, reverse is ok. I dropped pan and it was clean. I dropped valve body and found OD servo shaft clip broken, the large snapring was I fine and in place. It allowed the inner shaft to float up and down. Would this cause my forward gears to slip or do I have a bigger problem?
View 14 RepliesOk, my clutch has been giving me trouble for a little bit and I'm almost positive that I have a bent release fork. It also slips under heavy acceleration in 6th gear. I am planning on doing a clutch, compete with flywheel and release fork and a new rear main seal. My problem is, here within the last couple of days the trans would pop out of 4th gear if I was just coasting. It has been getting noisy over the last few weeks also. I'm no manual tyranny expert, but this is making me think I'm gonna need to have it rebuilt.
View 14 RepliesI replaced the old auto trans that was slipping in my 2000 golf with a same year auto trans from a beetle. The beetle had 115k miles and the PO toasted the 1.8t. I replaced the TCM also and when I finished the install I took it out for a drive this afternoon and when I shift it into drive it starts out in 3rd. It will manually shift through the gears but it will not shift from 3rd to 4th. Could I have left something unhooked? Is this a solenoid issue?
View 10 RepliesI finished installing an auto out of a 1999 beetle into my 2000 golf. I used the beetle TCM now it wont shift out of 3rd. If I manually start in first it will shift up to 3rd but nothing past 3rd. I had it scanned with a generic scanner and these are the codes. P1780, P1783, P0725. I researched the heck out of this and I'm not sure what to do. Do I need to take it and have a vag com hooked up to make sure the ecm and the new tcm are talking? It seems others have had these issues and I thought it might be solenoids but that's not what's coming up.
View 2 Replies1999 Jetta MK4 with only 124k miles on it. Everything is fine with the car except when the car shifts from 2nd to 3rd it is jerky/violent/forceful everything else is good with car except check engine light is on but I don't really care about that and I'll go check with autozone to see what the code is. I am able to feather the gas when I know its going to shift and I can make the shift pretty smooth. My question to all the experts is does this mean that this tranny is on its last leg or does it still have a lot of life left in it. My old Cabriolet did it for years and never was a problem.
View 5 Replies2003 jetta wagon 1.8t 106000miles with the tiptronic auto trans, has no forward or reverse, no codes, have already drained fluid and refilled, i can see the rpm gauge move when i shift from park to R to D etc, but it will not go at all, i'm thinking maybe the toque converter has failed.
View 6 RepliesI have an 04 Jetta 1.8T that I recently acquired and have a problem with a noisy manual tranny. Reverse is a bit noisy (more than usual) and when I get on it in 1st and 2nd gear it sounds like an awful whining noise. I have been told it could be either a bad throw out bearing or input bearing? BTW this thing shift perfect, like butter, no grinding at all.
View 4 RepliesSo I replaced the engine and trans engine mounts on my 2004 R32 today. After I got done and drove it there was some serious vibration and gear whine. It also seemed like I wasn't able to transfer all the power to the wheels, it was definitely slower to accelerate. Did something go out of alignment?
View 10 RepliesI had a small leak on the side cover of my trans so I decided to replace the gasket and take the opportunity to drop the pan and change the fluid and filter. However now I seem to have a pretty significant leak from the trans pan itself. The side cover seems ok.
The filter and gasket kit I purchased was a Wix brand. I don't have a torque wrench, so I just tightened to Germain torque spec (gutentight). However now I worry that maybe it's not the right spec, either too tight or too loose. The kit came with new spacers for the gasket and I cleaned the pan, especially around the lip where it interfaces with the rubber.
Will overfilling transmission fluid cause hard shifts? I used ~4.3 quarts to refill. How much should I drain out? My check engine light came on.
Basically, I am having hard shifts from 2-3 and 3-4 in tip mode and auto. more tip mode tho.
-I did a complete solenoid change b/c of cold start problem with n92 solenoid.
Fixed the cold start shifting out of first.
-Did a trans fluid change with Mercon V ATF Fluid works fine.
-Just changed oil on 4th of July last week.
Yesterday my check engine light came on. It's been about 500 miles since the solenoid change/trans fluid change, and 100 miles since the oil change.
Now my Mk4 is having this obnoxious shifting. I am thinking I possibly added too much trans fluid into my system as I do not have the VAGcom tool.
I drained out (bone dry drain till no more dripping from check/drain plug), roughly 4 quarts. I added 4.3 give or take 0.1 quarts back into the car.
Now I'm worried because everywhere I'm reading says anywhere from as little as 2.1 quarts to 3.5 quarts.
Should I drain out 0.5 quarts (because I know theres over 4 in there now) to make it 3.5 quarts?
Or should I just redrain the whole thing and start by measure one quart at a time?
Long story short, over torqued the top two stretch bolts and destroyed the threads. We helicoil'ed both holes and put the bolts back in. That was about 4 months ago.
Today both bolts snapped not while moving. We dolly'd the car home and bought a replacement bracket, however all three bolts along the bottom that go into the transmission housing broke off inside.
I'm a tad stuck at this point. I could drill and tap new holes over the existing, but i question whether that is a good idea. My other thought was to get 3 of the larger stretch bolts that go in the top, completely drill out the three that are broken and tap the big ones in. This thought would also require drilling the bracket to make the larger bolts fit.
My 2002 Elantra GT has been turning off while driving. The radio, lights, and other accessories remain on. The car doesn't lurch but all of the dash lights come on like when you're first starting a car. I was able to restart the car after about 10 min the first time and 5 min the second time it happened. 1 week between episodes.
Brought it to the garage and they couldn't find a problem while letting it run for 30 min. Also, there are no error codes. What could be wrong?