My 2001 Golf seems like the clutch is slipping. It bangs into gear at low revs so bad you think you've hit a large pothole. I'm hoping it's not the whole transmission that needs replacing, because we only have 135000 on the clock.
View 2 RepliesSo i have a 05 1.8t gti... just bought it about 3 months ago and it has a stage 2 south bend clutch... the car has only 68k on it and the clutch is slipping already... it was driving fine then about a week ago all hell broke loose and it's slipping bad... now for my question what performance clutch is recommended? I have a giac tune and its pushing about 21 boost... . would a 2.0 performance clutch work on the 1.8t?..
View 12 RepliesI'm a new owner of a 04 gti 1.8t. The car has been modified with a ko5 turbo @ 20psi, apr tune, 3" turbo back exhaust, hks bov, and a FMIC. The car is amazing, but with my luck after only a few days of owning the car the clutch started slipping.
View 2 RepliesI have a 2001 jetta with a Vr6 the clutch petal just goes to the floor. No return. What's could be wrong?
View 2 RepliesMy 2001 santa fe has recently had a new clutch fitted as the old one was slipping but, when towing our caravan at the weekend the clutch is playing up again but, this time the clutch is slipping at anything above 2500 rpm yet she is pulling fine below this rpm.
View 4 RepliesOk santa fe 2006 (facelift) clutch was slipping. We've put new clutch kit in it (thrust bearing; friction and pressure plate). We discovered it had already had the DMF concersion to single mass. So we ordered the single mass clutch kit for it and fitted. All back together, clutch won't disengage and allow you to put it in gear!!! So took it all apart again to check the fitting as the inspection hatch it just didnt appear all fingers on the pressure plate was being pulled.. all looked correct, thrust bearing snapped in to place as it should... we got box back on (making sure the lever entered the thrust bearing correctly) and still no luck. When you press the clutch you can pull the rubber on the slave cylinder back and the piston moves all the way to the circlip. There appears to be movement on the pressure plate in the box. At a complete loss.......... what could have happened?
View 3 RepliesMy 01 GTi (12v VR6) was having some trouble shifting into, and out of, first and reverse so after a bit of research I decided to try adjusting the shift linkage as it seemed like a possible easy fix. After doing that I tried backing it up in the driveway and after a couple of shifts to different gears it ended up getting stuck in reverse. When I pushed in the clutch pedal to let it roll forward I noted that it seemed to be resisting rolling forward despite the steep incline. Once it reached a less steep incline it stopped rolling forward completely, so I'm thinking that it probably won't come out of gear because the clutch won't disengage all the way.
I've done some searching around and from what I've read so far it sounds like it could be a worn or damaged clutch fork, the hydraulic lines, master or slave cylinder, or even a broken clutch plate. What I don't want to do is pull the transmission and clutch, only to find that it was something much easier to fix.
The clutch doesn't slip all the time. Sometimes when I put it in third then put the peddle to the floor, it slips for half a second then grabs. Lately noticed it in 4th and 5th gear too. When it does slip, it slips the whole trip. Then later that day it might not slip at all. At first I thought clutch was going, but when does a clutch get better? From what I remember it usually stays the same or gets worse. The fact that there's days it grabs perfect without a slip, leads me to believe something else is causing it. Maybe it's not disengaging or engaging fully.. linkage problem perhaps? I did a quick bleed, hoping it was air. Was better for a couple days after that, then started slipping again.
View 2 RepliesOur 2001, regularly maintained, Odyssey has only 208,000 miles on it, and the transmission has begun to misbehave. Similarly to a clutch's slipping with a manual transmission, sometimes the automatic transmission will "slip," that is the engine will rev without the car's moving. This has been most noticeable, and until recently only noticeable, when the car is first driven on a given day - usually not apparent once the car has "warmed up." My wife and I have independently observed that the problem is more apparent in colder, rainy weather. The problem seems to be getting worse - we've noticed occasional slipping now, for example, when accelerating to pass on a steep uphill.
Question 1: How might the association between the slipping and cold weather/engine temperature be explained?
Question 2: The Odyssey is about due for a new timing belt and water pump. That would seem not worth doing unless the transmission were fixable, in which case, it would seem best to take care of everything at once.
Should we do it, or is it time to retire this car? (We live out in the boonies and have to contend with dusty roads in the summer and drifting snow in the winter; we don't need a fancy car, but do need a reliable one - especially in the winter.
I've searched but can't find what my problem is , ON idle when clutch is not depressed loud ticking noise , but when I push the clutch in it goes away . Also the ticking noise will get louder if I accelerate . ONLY Im first gear will I hear a loud grinding noise which means I have to quickly switch into second . Sound similar to something being dragged along a fence . Again the grinding sound I'm first will only happen if I'm giving it gas. Car has 325,000 km . Something with the transmission ?
View 1 RepliesI just had a new clutch installed yesterday. Bully stg3 with flywheel. My 2012 R has 22k. I had to change it since my stock clutch was slipping at 3000rpm with the Unitronic stg1+.
The second I start the car and stay on neutral, give a little gas I hear a super loud grinding noise. It stop when I press the clutch. On idle I don`t hear nothing and when I drive everything is fine until I release the clutch and when I don`t press the gas.
The shop said they never heard anything that loud and they confirm that everything was installed correctly. Other then the noise the clutch is fine and works very well.
Well the clutch started slipping finally, not sure if it was the weather change on the drive from here to PA but I slip 5 and 6th wot 4-5k rpms. Have some coin set away because I knew it was going to happen sooner or later did some searching and I'm curious to here the verdict on the RSR clutch how many miles and how its holding up as well as whatever else you are running. Will probably keep the car 2+ for quite a while so not really worried about 3+ power.
View 24 RepliesMy wife was driving my Stage 1 R last night (by herself) and she ran into an issue where when she tried to leave from a red light, the clutch was slipping through the first three gears and she could barely get up any speed. She pulled over, let the car sit for a few minutes and then started going again with no issues.
She drove home about 5 miles and told me about what happened. The car smelled like burning clutch, but when I took it out for a quick test drive, everything seemed fine.
I am at around 5000 miles and have never had any issues before and I don't ever do high-rpm launches. So, could this have been a fluke or a sign of the clutch/pressure plate issues people have been having?
Well I was hoping it was just a fluke the one time it slipped about a month ago, but my clutch is now officially toast. If I'm between 3-4k RPM and punch it in just about any gear I'm getting slip. Trying to pass a car on the highway, and I'm getting slip. I do not launch my car, I simply like to play in the 3-4k rpm powerband as I love the torque. Apparently spirited driving while remaining in the peak torque range of the engine will kill the stock clutch. God only knows how long the OEM clutches will last with people that drive their R like a racekar... 3200 Miles, Stage 1+ ....
View 24 RepliesI have an issue that I thought was a slipping clutch, but my dealer says it isn't. If I'm cruising at highway speed (stg1 gti)say around 65 and I get on to pass the revs will surge, but there will be no apparent acceleration to go with it. The dealer said it isn't the clutch because there is a standard test they do where it would be jerky in 2nd. Could this be a DV or something?
View 24 RepliesI went stg.1 at 1000 miles & stg.2 around 6000
miles, then K04 I'm at a little over 6400 miles & my clutch slips in 4th & 5th gear. I never got the chance to install my APR inner cooler. I really hope the Southbend stg.2 endurance setup works well so I can move on to the suspension. This hobby can get expensive but the car is a blast to drive! It never fails to put a smile on my face & has definitely taken the smile off other drivers faces when they realize they can't get by me.
So I have a stage 2 endurance clutch and light weight flywheel on my car. I had not really gotten on it of late until yesterday. I was getting on the highway and really got on it. When I hit third gear it felt like my clutch was slipping. I have only had it on the car for like six months and about 10,000 miles. It could be worn out all ready? And after the incident yesterday I pushed the clutch in and held it to let it cool down a bit after it did it held fine even in higher Rpms didn't feel like any kind of slipping. Pulled very strong. This morning after having all night to cool off (and I mite just still be freaked out a bit) but it seemed to feel different, like a possible slip at 3,000 Rpms but again I mite just be freaking out about nothing. What does a master cylinder or slave cylinder going out feel like?
View 1 RepliesSo my clutch started to slip in 4th when I first got my apr stage 1 tune at 24k miles. now 600 miles later it's slipping in 3rd. put it back to stock mode and it doesn't slip in any gear.
My question, if I replace my clutch with an OEM sachs what are the chances of it slipping again? From what I understand the golf R uses the same clutch disk and pressure plate as the gti so why is mine slipping so early? luck of the draw?
I prefer oem because it is a lot quieter and I do not plan to mod any further than stage 1. I'm still running the stock airbox.
I am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.
Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.
My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.
1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.
I know some of us drag race our cars from time to time. I have a fair bit of bolt ons and I was just wondering what I would run so I had her out 3x yesterday. Impressed with my trap speed of almost 100mph on an 85-degree day w a stock intercooler but not my times, so much so that I don't even want to say them.
I was shifting a little after redline as quick as possible and leaving at like 3000-4000 rpm.
Is my clutch slipping or where am I going wrong?
the suspension is mostly stock as are mounts. I am sure I will get better with practice but this was a really sticky track so I really cant blame my tires
So I got my stage one flash yesterday and I noticed 5th gear slipping already. I don't plan on getting a k04 upgrade, maybe stage 2 down the road. so I am looking into the drop in clutches, preferably this one [URL] .... I am just trying to find out some reviews from people who are currently running drop in clutches and the issues that they have come across.
View 8 Replies