Golf IV / Jetta IV :: 2001 - Brake Pedal Goes Halfway Down Before Pressure Builds
Aug 21, 2015
My mom's Jetta has had a squishy brake pedal ever since we got it a couple years ago. I figured it went down so far because the brake pads were wearing thin.
After having just replaced the pads and rotors, I flushed the fluid with the Motive power bleeder. I cycled the ABS pump with VCDS, then hooked the power bleeder back up and opened all four corners again until fluid was flowing clean and bubble-free.
Everything went well with the change, but the brake pedal never got as firm as I expected it to. Before the change, the pedal felt like it would get dangerously close to the floor. The brakes always worked, but the pedal hit about 60-70 percent of its travel before the car started slowing down. After the change, it has improved slightly, but it feels like its going about half-way before the brakes start working.
The pedal doesn't drop when you hold pressure on it like I figured it would if the master cylinder was leaking. Is this normal for a mk4 or does it sound like there's something wrong?
Car is a late 2001 2.0 Jetta Automatic with the MK60 ABS pump.
View 1 Replies
Advertisement
So I have a 2004 Jetta 1.8t. Recently I noticed an issue with the brakes. It is a rare occurrence that this issue happens. Maybe 1 out 6 times I slowly stop the brake pedal seems to put pressure back against me applying brake pressure and makes somewhat of a grinding noise and the brakes don't seem to grab as well. But a split second later the brakes return to normal and grab as expected. Could it possibly be air in the brake lines or something totally different?
- Front brakes are in excellent condition.
- Just replaced the driver side front abs sensor and put new rear brakes and rotors on.
View 1 Replies
2001 2.0
251,xxx km
Noticed here lately that my brake pedal is depressing further, and can go to the floor if I press it hard enough.
If I press the pedal quick (panic stop) it engages quickly and in the correct spot (I can feel the front tires almost lock up) then it depresses more almost to the floor. the brakes still work perfect however.
What should I try first?
I use my hand brake, and have pumped the brakes and pulled the handbrake to set the rear pistons in place.
I replaced the two rear calipers about a year and a half ago and bled them obviously. Have not bled the front brakes and will do that, but was just looking for more insight, and common problems, vacuum leak, etc.
Reservoir is full as well, and no brake line leaks that I know of.
View 16 Replies
I just finished installing a new clutch kit on my 2003 Jetta Wolfsburg Edition 1.8 and I have absolutely no pressure on the clutch pedal, I am pretty sure I installed everything correctly. How do you bleed the clutch lines, how do you know if the slave cylinder is bad. When i push the clutch pedal it just goes to the floor with absolutely no return.
View 4 Replies
Im having problems with my brakes mainly being pedal pressure. It's really really soft and has no bite till near the bottom which could be due to the res being low on fluid since both rear calipers seem to be leaking from the handbrake mechanism. When I got my car safetied they fixed my handbrake but I think they put the adjuster to tight cause I felt more rub then what I thought was normal but could be completely wrong. Not to mention this starting happening the day after I got it safetied
the handbrake bracket didn't retract like the other side but since then I loosened the compensator and pulled both side handbrake lines off and retracted the handbrake bracket by hand so now it looks like the right side.
View 5 Replies
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 Replies
A couple weeks ago I bought a 2001 VW Jetta with 176,000 miles on it. The car runs well, but for the past four days this has been happening:
Every time I start the car, after it's been off for a couple hours, neither the gas nor the brake pedal work. I can push them down, and I hear the car trying to respond but it doesn't do anything (well, it does move a little, as though it's in neutral). Then, when I turn the car off and then turn it immediately back on, both pedals are back to normal and work perfectly fine again. It's happened every time I start the car for the past few days.
View 1 Replies
At times my windshield wipers stall halfway up my windshield or move really slowly. Other times absolutely fine, I already checked both battery terminals and niether were the issue. What's the best way to get to the wiper motor to check the connections. Or does it sound like a ground strap issue elsewhere on the car.
View 5 Replies
I got a mk4 where the temp gauge starts to climb to 3/4 instead of halfway when I'm idling for a while.
1. fans don't come on
2. if I turn on ac, fan come on and temp stays at 1/2
I tested low and high speed on fans. both operational. Is it the fan control module, temp sensor green top, or radiator s/w?
View 5 Replies
The brake pedal on my Golf 4 GTI 132KW pulsates when I put my foot on the pedal going over uneven terrain without pushing the pedal in.
View 1 Replies
I "Bulletproofed" my f-250 Super-duty last summer and she ran great for a time, actually she is still running great, except for one thing that is driving me crazy. On a cold start it turns over until the oil pressure builds up. Then she will crank and runs fine, also starts normally after warm, turns over a couple of times and cranks.
I have oil in the filter housing, have replaced the seal at the bottom of it. Just pulled the oil rails off and replaced the seals on them, and a new IPR seal and filter. I am still having the problem, F.I.C.M. voltage has been fluctuating between 45 and 46 vdc. I have a P300 and P308 code.
I haven't really considered Injectors because it is idling smooth as silk and has great power.
View 7 Replies
My oil pressure light is blinking and there is a faint smell of burning oil. I recently had an oil change after letting my car sit for 5 months after the oil pan was replaced. I have checked oil levels and it is just right. I have asked around and everyone comes up with a different answer but they also say they are guessing due to lack of experience with VW's. The light only comes on when the car is moving. When idling, everything appears to be fine.
View 16 Replies
I have a 2000 Silverado 1500 replaced calipers, master cylinder, and ABS Pump/Modulator. Bled all four calipers. Brake pedal spongy and has very little pressure and travels all the way to the floor. What am I missing here?
View 8 Replies
I just got a 2001 Jetta 2.0 (I know slow but I needed a work vehicle) and the dash lights and passenger rail lights don't work, the check engine light, fuel light, all those type of lights work, but the speedometer and blinkers and that stuff don't work, and then the blinker works in the back but no break light. I'm pretty good mechanically but when it comes to electrical stuff I'm completely stumped. What it could be? I haven't looked into anything due to just getting it last night and having to work this morning.
View 3 Replies
My old 1997 Dodge Caravan (150k miles) has weak brakes. During normal driving, it needs more pressure on the pedal to brake normally, than any other car that I have driven. This would be ok as I can push hard on the pedal... But the problem is that, past some point, I get no additional braking power no matter how hard I push.
So in case of an emergency, I cannot come anywhere close to lock the wheels (and this car does not have ABS). So basically, the braking power is proportional to how hard I push, up to a point where the braking power remains the same no matter how hard I push. At that point the pedal is maybe 1/3 down, still very far from the floor.
I have just replaced the front pads and rotor with no improvement. And when the engine is not running, the pedal gets really hard after I depress the brakes 3 times, indicating that the booster is doing something. The car will stay in the driveway for now as this is a dangerous situation.
View 6 Replies
Replaced my rotors and pads and I still do not like the braking feel as I apply constant pressure to the pedal. No matter what I do, I cannot apply even or consistent pressure to pedal and get the car to slow down smoothly or in a linear way. It feels like some power assist component applies varying force to the calipers no mater how slowly or quickly I try to slow the car down. It just isn't smooth like other cars I own. The brake pads grab fine, no warped rotor issues. Does your car brake smoothly from 40 MPH to 0? Is there some power assist unit that may be going out?
View 2 Replies
My friend's Jetta was running fine. One day about to drive out of the driveway it started doing 2 things:
1. Felt like it lost power braking, just stopping by manual effort by pushing down pedal hard.
2. Engine stalling unless you keep the gas pedal depressed and holding the engine to about 3,000.
Car currently sidelined until this is fixed... Having the brakes go like that at the same time is strange so where to start. Brake fluid level is fine.
View 2 Replies
I have only 42k km or 26 k miles. Brake stops but soft. The brake pedal sink if you apply pressure after a stop. Feels like someone open a valve. The pedal go to very low. I am find the stopping power is poor. Brake fluid is brownish. I hope it is not the master cylinder.
View 20 Replies
MY 2005 chevy silverado 2500 developed brake problems. The power steering pump, master cylinder, and Hydro static something or other has bee replaced.Now the pedal fades with constant pressure. The shop tells me this is ok but today at at a downward sloping boat ramp with the pedal at the floor, it was very scary.Before the parts were replaced this problem did not exist.
View 2 Replies
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 Replies
I own a 2000 Hyundai Accent with 85,000 miles on it. I recently took my car into a local shop because the pressure on my brake pedal was extremely low. I was almost pushing it to the floor. On my first trip to the shop, they replaced the rear wheel cylinders because they were leaking. This replacement didn't fix my problem.
On the second trip to the shop, they replaced my master cylinder. I did call around to other shops to do a price comparison and the price was reasonable on both jobs. This work was done about two weeks ago.
At first, this seemed to fix my problem, the pressure was perfect. Since then I've been having an intermittent problem with the brake pedal pressure changing. It would get a little hard during driving, but would correct itself after a few moments. I don't drive that often or very far, so I was waiting to see if the problem would get worse.
Last night it did. I went out and when I tried to drive my car home my pedal was extremely hard. I could barely push it. While I was driving my car home (I was close to home), it felt like I was driving with my brakes on. My car would stop as soon as I took my foot off the gas pedal, I could not coast. When I got out, I could feel heat coming from the front tires, which I didn't even have work done on. There was also a smell that I've never smelled before. It almost smelled like something burning.
I was told I should have my car towed back to the shop on a lifted bed and not rolled there and that they should fix my car at no charge because they did something wrong.
My ultimate question is did the shop do something wrong and should I take it back to them if they did? Should they be responsible for this new repair? I don't want to go demanding anything if it's possible this is a whole new problem and not their fault. Even though it does seem like an awfully big coincidence. My next question is: what could be possibly wrong with my car? I would like to know what I'm getting myself into.
View 1 Replies
