Golf IV / Jetta IV :: 2000 - Rough Idle - Flashing Check Engine?
Aug 1, 2014
The check engine light came on in my 2000 Jetta and the engine power suddenly decreased noticeably. Got worse quickly and was idling rough, like it was about to stall out (but didn't). Took it to dealership, they said spark plugs were the problem and replaced. All seemed normal driving home, but after 10 minutes, same problem: check engine flashing, weak engine (trouble on hills), and a rough idle.
Two questions: what could it be?
and is it safe to drive back to dealership (~10 miles) or might that cause further damage?
View 1 Replies
Advertisement
I have been experiencing some issues with my '06 rio5 (same engine as your hyundais). this forum is way more active than the kia forums, so figured id give it a shot here.
I am experiencing a rough idle at start up while the car is low on fuel (<1/4 tank). it idles rough for a few seconds, the check engine light flashes a bit, and then it runs fine.
The car is an '06 rio5 with approx 19k miles on it, five speed manual. Also, sometimes after refueling and it will just shut off while waiting at an intersection. Not sure whether these two issues are related, but thought i would mention it just in case they were.
View 14 Replies
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
View 12 Replies
My check engine light just appeared like an hour ago. In idle, it sounds like a big flicking V8 Supercharged (I actually feel the car vibrating) and I need to give it a LOT of gas to start in 1st. When I turn the key, it takes a while to start. It is flicking weird. I am dropping my car first thing in the morning, but somebody got that so far?! And the last thing I did before getting the light is reversing in a parking lot and parking my car. I have my car since december.
View 6 Replies
I have a 2000 jetta 2.0, and the idle seems to rough and when I start the car it seems like I might stall.
View 9 Replies
So my gf's check engine light on her 01 Golf flashes once in a while, and it misfires. But the thing is, it doesn't stay on, and it's once in a while (like once or twice a week). She has new spark plugs, and new wires. I have a feeling it's the coil pack, but I really don't know if it needs to be replaced until the check engine light actually stays on.
View 14 Replies
Just a few days ago I was driving and I noticed as I went over 35 mph my car would stutter and the check engine light would start flashing. And when I slowed back down the car drove fine. I'm wondering what the problem could be? Feels like the car is losing power. Car is currently at 119k miles.
View 1 Replies
a 2011 jetta. brake pedal is hard no pumping action. The car show check engine. The idle is not smooth.
View 2 Replies
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
View 10 Replies
Having trouble with my '00 Jetta 2.0 A/T w/ 98K miles. Had the water pump replaced @ a year ago (for the 2nd time, the 1st replacement died after <15K miles.) The car has had issues with rough idle when started, especially with a cold engine, since before the 2nd water pump. I've replaced the coil pack, thermostat, and coolant temperature sensor in the recent past in addition to the water pump & timing belt.
The gas mileage sucks, and when it's idling rough it doesn't "idle up", & will stall if the gas pedal is pressed with 30 secs. of starting. Otherwise it seems to run fine. The coolant temp. sensor was replaced after a CEL indicating it was bad. The CEL went off after it was replaced, but it's now throwing a P1296 Cooling System Malfunction. I have noticed the temperature gauge fluctuates instead of staying around the "middle" since the 2nd water pump replacement, and will run "colder" in colder weather. Since spring is here, the temp. gauge stays around "normal", or the middle.
Some research online says thermostat OR coolant temperature sensor. Since the gauge registers normal now, I'm leaning towards a bad temp. sensor...?
Does the hard start/rough idle and the cooling system malfunction CEL could be related?
View 2 Replies
2000 VW GOLF 2.0L, manual, ~190k miles
Driving down the highway my CEL started flashing and the engine power dropped at the same time. I drove two miles to my destination and the idle was very rough and the power was still very low. The codes were P0300, 0301 and 0304.
The coil was replaced about 2 years ago. The plugs have never been replaced. About 2 weeks ago I had a solid CEL with the codes P1255 and P0422... I purchased a new ECT Sensor but did not yet make time to install it.
Could everything be related to the ECT? Or do you think there are multiple issues?
View 5 Replies
I have a 2004 gls 1.8t Jetta. It has a straight piped turbo back exhaust, and a stage 2 tune. I recently had a problem with my car starting to rough idle when the engine gets to proper temp. The car starts to idle roughly, and when driving the car will bog down, if I keep my foot on the gas, the car acts like it is coasting and the rpms fall, but at some point the car will shoot off like i floored it. At lower rpms in the 1st and second gear, the car will randomly and periodically start bucking, with the same symptoms. I already replaced my coil packs and spark plugs with a kit off ecs, and when i went to change the spark plugs i had oil on the spark plugs and oil leaking from a bad valve cover gasket, so that was replaced as well. I replaced the fuel filter already.
The MAF sensor was just cleaned and didn't look too dirty. When I unplug the MAF it still idles rough. The fuel pump relay can be heard working properly when the door opens. Another problem that sometimes occurs on cold start is if I don't wait long enough for the pump to activate or sometime right after it starts, the car will start partly then stall out. When driving and the car is bucking the exhaust gives rich fuel smell. Also when 2 stepping in the car (which I don't do very often), the CEL starts to blink and the car misfires and drives rough. I figure since I don't have many parts on it yet I probably shouldn't do it anyway so I don't blow up the engine.
View 3 Replies
On my way to work, my check engine light started blinking and car was sputtering (real bad on idle). I ran the code and it came back with misfires codes. I changed the coils/plugs, fuel filter and fuel pump last year. Can the coils be bad already? When I clear the codes the car will run fine for a little while. But after a couple miles CEL will blink and the car will run roughly again.
Car : 2004 Golf 2.0
Codes:
16684: random multiple misfires
16648: fuel injector #2 short to ground
View 5 Replies
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
My 2000 deville (which i never drive) but start up and let run decided to give a BIG problem today. I went to charge my a/c up and when I started it it was running very rough... Last week it did it also but after letting it run it smoothed out but today it stayed same and was actually worse. I drove it around the block and check engine light was flashing and car was sputtering like it didn't want to go. Sputtering out of exhaust and exhaust was getting real hot and giving off smoke from behind tires area. it was actually starting to burn my grass. I don't understand why it would do this all of a sudden. I pulled codes and this is what was there
p01571
u1040
u1064
u1192
The only code that is usually in there is the tcc code and its been for years..
View 5 Replies
I have a 2000 Subaru Outback. The check engine light has been coming off and on for the past couple weeks, but today the light started flashing. The car is running a little funny - not accelerating well and shaking when I start it. What's wrong with it?
View 4 Replies
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 Replies
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
View 5 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
We have a 2008 f250 super duty with the 5.4 triton well ever since I replaced the power steering pump its been running raggedly, it idles rough and when i get up to 50, 55, 60 the check engine light comes on i put a diagnostic reader on it and said something along the lines of ECU bank 1 an Bank 2. What that is and I've been a mechanic for almost 3 years.
View 2 Replies
