Golf IV / Jetta IV :: 2000 - P1296 Code / Hard Start And Rough Idle
Jun 10, 2014
Having trouble with my '00 Jetta 2.0 A/T w/ 98K miles. Had the water pump replaced @ a year ago (for the 2nd time, the 1st replacement died after <15K miles.) The car has had issues with rough idle when started, especially with a cold engine, since before the 2nd water pump. I've replaced the coil pack, thermostat, and coolant temperature sensor in the recent past in addition to the water pump & timing belt.
The gas mileage sucks, and when it's idling rough it doesn't "idle up", & will stall if the gas pedal is pressed with 30 secs. of starting. Otherwise it seems to run fine. The coolant temp. sensor was replaced after a CEL indicating it was bad. The CEL went off after it was replaced, but it's now throwing a P1296 Cooling System Malfunction. I have noticed the temperature gauge fluctuates instead of staying around the "middle" since the 2nd water pump replacement, and will run "colder" in colder weather. Since spring is here, the temp. gauge stays around "normal", or the middle.
Some research online says thermostat OR coolant temperature sensor. Since the gauge registers normal now, I'm leaning towards a bad temp. sensor...?
Does the hard start/rough idle and the cooling system malfunction CEL could be related?
View 2 Replies
Advertisement
I have a 2000 jetta 2.0, and the idle seems to rough and when I start the car it seems like I might stall.
View 9 Replies
I was cruising down the highway and my check engine light came on. I was a few minutes from a auto store and they said my code was p1296. I found out it is either the thermostat or the coolant temperature sensor. I wanna know where it is located in the engine bay. I have a 02 VW Jetta 1.8T.
View 1 Replies
I have a 2002 Manual VW 1.8t Jetta, and searched everywhere on the net and couldnt find anything. The problem is my RPMs skyrocket very high, like up to 6500, wheteher I give it a little gas or try to speed up to get on the highway. It seems almost as if the car thinks it is not in gear, I get no power or gain no speed when this happens. And it happens in every gear, 1-5. This is the main problem I am trying to figure out what it is.
Now I got the code read for the CEL and is is a P1296 and I know that this code means that I have a bad coolant temperature sensor or possibly even a thermostat itself. I just bought a new temp sensor and plan to replace it tomorrow or the day after. I cannot imagine that this is what is causing the problem with my RPMs to skyrocket uncontrollably when accelerating.
View 2 Replies
My 2004 Rubicon has been having some idling issues. It idles kind of rough (+- 200 RPM) and is hard to start. I tried to start it recently and after 4 cranks, it started then the CEL came on, and has been on ever since. I have recently moved from Washington state to Houston Texas, and the problem starterd here in Texas. I checked the code and am getting a P0505 code. I had a mechanic replace the IAC valve, Checked for vacuum leaks, and cleaned the throttle body. The mechanic says the output from the main computer appears to have burned out, and needs to replace the main computer(for $1000). The mechanic can clear the CEL, but after turning the jeep off then back on it reappears. The mechanic says he verified the computer was the problem by installing a known good computer and it cleared the problem. Does this sound right to you? If my computer is bad, wouldn't my whole operation be affected?
View 4 Replies
2001 VW Jetta 1.8t automatic.
Transmission has a hard time going into 1st and reverse. Also some times hits hard going into third. I have a CEL for a vehicle speed sensor? Was wondering if it's not the VSS but maybe one of the other tranny sensors?
Separate question. Same car has a rough idle issue. Occasionally stalls but intermittently runs normal always has a low idle around 600 rpm. I have a code for an injector on cylinder three.
VSS code : P0725 - engine speed sensor circuit malfunction
Injector code : P0203 - injector circuit open cyl 3
View 4 Replies
OK. I'm getting a P301 code on the OBD in my 2000 Expedition (5.4 L). Already replaced plugs x 8, coils x 8, & fuel injectors. Still have rough idle when it starts up, usually for a few minutes & then it's mostly OK. Maybe a small rumble now & then when @ a red light, etc. Replacing fuel filter & all 4 o2 sensors tomorrow.
View 9 Replies
I just replaced my injectors in my 12v vr6 and now having some problems. Mainly having issues with start up. Having to feather the gas to get it to start and still runs rough for a min or two.
View 3 Replies
The check engine light came on in my 2000 Jetta and the engine power suddenly decreased noticeably. Got worse quickly and was idling rough, like it was about to stall out (but didn't). Took it to dealership, they said spark plugs were the problem and replaced. All seemed normal driving home, but after 10 minutes, same problem: check engine flashing, weak engine (trouble on hills), and a rough idle.
Two questions: what could it be?
and is it safe to drive back to dealership (~10 miles) or might that cause further damage?
View 1 Replies
2001 Jetta GLX, 12v 2.8 VR6 Automatic, 157k miles.
Relevant Info: P0411 code, unknown if associated with my slightly rough idle and recently reduced mileage (down by 3-4 MPG). I see 2 N80 valves, one by the power steering reservoir and one behind the throttle body attached to the fire wall. I removed them both, got a tiny bit of what may have been charcoal out of the lower valve and tested both with a 9 volt battery. Both were closed with no power and open when I attached the battery. I cleared the code and it returns within 30 minutes.
Possibly irrelevant info:
Changed the timing chains 3 weeks ago and the code popped up just afterward. Prior to changing the chains, all I saw was a Cam Position Sensor code that is now clear. The slightly rough idle was present to a greater degree before chains were changed but has improved.
SAI solenoids look good but their little rubber hoses don't look fantastic. Could this contribute to the rough idle or is it not part of the vacuum system?
Ignition coil is new and all plug wires tested to about 6k ohms.
I've looked up other's experience with P0411's and have seen the list of possible causes. Wondering if I'm missing a possible cause, if I can test the system further without having to buy parts etc, if the reduced mpg's and rough idle are related...
View 3 Replies
I have a 2003 2.0 gas Jetta (181k miles, automatic.) that won't rev over 3k, starts rough, idles rough and wont stop setting a P0341 cam position sensor code.
The car was not running when I got it, I replaced the coil pack and it ran but not over 3k. Cleared codes, it sets the P0341 immediately.
Had timing belt, water pump, tensioner and cam pos sensor replaced. Still, sets p0341 code, starts rough, idles rough and wont rev over 3k.
The throttle servo makes a little noise when actuated, shop thinks this is my demon - suggests replace throttle body. This car is for my son who will be taking it to college soon.
View 3 Replies
I'm having a little issue with my 03' vr6. I've had the car for almost 2 months now, which it's pretty new to me, since about the time I got it, the car would sometime roughly idle on start, just for a few seconds, maybe for 10-15 seconds, and then it'll go back to idling at 600-800 rpm and being normal.
This has happened maybe 5 times since I've owned the car, and since then I've changed the battery, and cleaned my MAF. The other day when I started my car it (the rough idle on start) lasted for maybe 30 seconds, so it kinda scared me a bit.
Also there is no check engine light. Other than the weird idle on start, the car feels responsive, quick and there doesn't seem to be lack of power. This is the only mk4 gti I've driven fast in, so there may be lack of power and I just don't know it.
View 2 Replies
I have an 03 vr6. I'm getting codes p0300, 0303, and 0304. I changed the plugs and the coils and still has changed nothing. In the morning when I first go to start the car it has a rough start and idles rough. But after letting it warm up it is fine. It drives perfectly fine, no misfires. None of this started happening until the car ran hot a few weeks ago. Did a compression test and everything came up fine. So would could my issue be? I'm at a loss here. I was thinking fuel issue but if it was a fuel issue, wouldn't it run rough all the time?
View 15 Replies
I got 2000 tdi with 270000km on it and have a few issues with it and am looking for some information before i start doing some work to it.
First problem excessive blue smoke on start up also runs ruff tell it warms up.
Second the is a screeching noise on start up some times. happens most of the time when the car is cold.
Third sounds like something is dragging or rattling but i have checked and there is i can see.
Fourth when the clutch is in and the brake is on the car runs ruff at idle. i think it has something to do with vacuum used for the brake booster but not sure.
View 1 Replies
My wife drove the car to work, and it ran good. She got a check engine light, but it was not on when I got home from work. I started the car and it idled fine for a couple of minutes and then it stalled. I check the codes and there was nothing locked in. There was a pending coding P0321. I am not sure what a pending code is, but I assume not enough to trigger the check engine light.
After work each night this week I tried troubleshooting but I have not gotten anything accomplished. Each night the car would start fine but if I turned it off it would not start until many tries if at all. It turns over strong but won't start. I drove it around the neighborhood today and it stalled and wouldn't restart.
The fuel pump primes. When the car won't start the fuel pump relay clicks constantly. Is this normal? I replaced the fuel filter because it has been 50k miles. Is the crank shaft sensor the problem? I hate to throw money at parts that aren't the problem when I can't get a code to trip the check engine light.
View 4 Replies
a 2011 jetta. brake pedal is hard no pumping action. The car show check engine. The idle is not smooth.
View 2 Replies
Check engine light had come on, the car was running rough at idle and it would crank hard. So I threw my code scanner on it only to find out it wouldn't link. Drove it to O'Riley's and had them pull the codes. It ran rough and had next to no power on the way there. O'Riley's pulled the codes and we got a P0300 (random multiple misfire), P0301 (cylinder 1 misfire), P0302 (cylinder 2 misfire), and a P0496 (EVAP emissions system high purge flow). So once I got it back to the house, she told me that she had the codes pulled once before and that they told her it could be her gas cap so she replaced it. She also stated that she had replaced the plugs about 3 months ago.
So with new gas cap and new plugs, and these codes, I did a bit of research and come to the conclusion that it'd replace the purge solenoid. The solenoid was making a pretty loud ticking noise and when I pulled it off, it rattled so I figured that was the fix. Pulled her plugs and you can clearly see that cylinder 1 was running VERY lean and cylinder 2 was a little richer but still too lean. Plugged the plugs back into coils and laid them on exhausted. Turned the car over and we had spark. Lead me to think the misfire had something to do with the P0496 EVAP code. Put everything back together and erased the codes. Gave the car back to her and told her to let me know if the light came back on. That was Wednesday last week. Sunday she told me the light came back on and the only code that came up was the P0496 again. When I gave it back to heron Wednesday, it would still crank hard but would start.
Battery is new and checked good, alternator is pulling about 14v and checked good and the starter checked good. My dilemma is the code and the hard crank. She told me that it only cranked hard for her once so I am assuming that has gone away but we're still left with the P0496. I am not 100% sure as to how this system operates but I understand it for the most part. She told me that she had just put gas in it before the light came on. Not sure how much time had elapsed after filling it and the light coming on but I do know she put gas in it. If it's a high purge flow, that makes me think there may be a leak in the system but I'm not sure where to go from here without throwing a bunch of parts and money at it.
View 14 Replies
2005 f150 5.4.
I have a slightly rough idle and can feel a miss at 1600 to 2000 RPM. Sometimes running about 65 MPH up a slight grade I can slowly press the gas pedal and the engine will begin to miss much worse, causing the truck to shake pretty bad. When it gets this bad it will slowly flash the CEL and I get a P0306 code (Cyl 6 missfire).
The truck has 148000 Miles on it and the plugs were replaced at approx 120000 by the dealer.
In the last week I have replaced the plug in cylinder 6 (looked ok) and have replaced all the COP's along with the fuel filter and the injector on #6.
I haven't been able to get it flash the CEL light or throw a code since replacing the COPs though and I am at a loss at to what to try next.
View 2 Replies
My coworker is giving me a clean 2001 Santa Fe with 151000 miles. It was running fine then all of the sudden it lost power but was able to stutter home. I went to check it out it started fine but idled a little rough. When I revved the engine it rose to about 2500rpm and stuttered then stalled. Kind of like it was rich and choking out. It then had difficulty restarting.
View 10 Replies
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 Replies
[URL] I even pulled the same P0170 code. And what I need to do before I spend a boatload of money and wind up sleeping in my car instead of driving it to work or lack therof is to start a troubleshooting list starting from where Sabot's update left off, i dont even know where the vacuum line is that he mentions and if i sprayed carb cleaner on it would i get a jump in engine RPM or a stall as a test?
What I have done: Cleaned MAF sensor, changed fuel filter.
What I have not done: Checked all vacuum lines, Tested fuel pressure, Tested for compression issues due to blown head gasket.
there is also a puffing noise coming from the exhaust side of the engine, im gonna grab a bottle of baby powder this afternoon and test for air leaks, i dont believe it is a misfire...
View 3 Replies
