Golf IV / Jetta IV :: 2000 - Misfires Only When Cold But Fine Once Warmed Up?
Mar 8, 2016
My brothers car is a 2000 VW Golf 2.0 that recently started starting rough in the morning, when the motor is cold it will struggle to even turn on and will act like its only running on like 2 or 3 cylinders for a second and most cases stall, he is having to pump the throttle to get it to even stay cranked until it all sudden just starts idling fine and it idles perfect but still acts boggy if you try to rev it right away as its warming up, after about 10 seconds of it idling the motor can be revved perfectly fine and you can turn the car off and it will start back up immediately..
View 1 Replies
Advertisement
This 1996 (220KM) car will run fine (perfect)for about ten minutes from cold (I'm talking -5 C)then starts to misfire when warmed up. Difficult to pull away (automatic) from a stop. Sound like its missing on two cylinders. Really chunters.
Installed new plugs, wires, cap, rotor, coil,filter. Don't know what to check next. Car will work at speed but I can feel it missing. Gun it and it will go. Doesn't appear to be a fuel problem.
View 8 Replies
Is this a warm stall issue and if so what is the actual solution to it ?
- Car is warm it will stall out at times after start . Giving it some gas will save it from stalling
- When dead cold it will have a very sluggish start
New plugs and coils. New fuel pump fuel filter & regulator . New crank sensor . Throttle body cleaned as well as maf. evap leaks all sealed up too. battery is good too
Very frustrating. Only solution would be to leave it at a shop for at least two hours so they could do live scans. But I'd rather not pay two hours of labor for nothing.
[URL] ....
View 8 Replies
My 2000 Jetta gls vr6 automatic was not shifting into reverse until it warmed up a bit, so I did a filter and fluid change, car level, warm pumped fluid while shifting gears. No problem. Next morning no forward fear, guess I split the gasket by over tighting. Had it towed home. Oh, tried to get to work, adding fluid made it go. Now now gasket and fluid. No gears at all. Generic code reader said electric malfunction on every shift solinoid, torque converter lockout and something about shift timing malfunction. Basically everything connected to ribbon harness. What's up? Did I fry it. Also I have a 2002 triptronic from my 2002 vr6, suppose that's not a bolt on?
View 1 Replies
My 2000 Toyota MR2 started to act up a bit lately.
I noticed that the car cranks fine, but turns over very weak. almost seems like it barely starts. This happens ONLY when the car is already warmed up. This does not happen when car is starting from cold start. Like, starting first time in the morning is fine, but after 10 minutes of driving, then turned off, the subsequent starts are weak as a fart from a butterfly. But it does start, and when it does... it seems to drive okay.
Now, I've been hearing it can be leaky fuel injectors, or... Mass Air Flow sensor, .. or .... bad fuel pressure..(which may be part of leaky injectors?)
View 19 Replies
I have a 2000 Toyota Echo. Symptoms are, the car drives fine until warmed up. Once warmed up, about 10 min or so, there is surging, an inability to maintain idle, periodic loss of brake assist, all consistent with my p1349 code. This happened about two months after I changed my oil (the old oil was in there for an embarrassingly long time). I ran motor flush and again changed the oil; symptoms persist. I have removed the OCV and OCV screen; both look fairly clean. Here's the question: what checks can be done on the OCV itself before I call a bad OCV and replace it? The service manual was of only marginal quality in explaining any checks.
View 2 Replies
I took my 2000 Jetta GLS 2.0 5 speed it a certified mechanic shop that I have used before. This scan show a speed sensor (which I already replaced) and the ECU. He said that the ECU is discontinued and that he could not do the repair.
The car will run fine for 10 minutes then will stall, wait 5 minutes and it will run again for 5-10 minutes stall and repeat the process. Question, what is involved with swapping the ECU with an identical numbered one from a junk yard? Also could swapping out my headlight assembly have any effect, this started to happen shortly after the new headlights were installed.
View 6 Replies
A cold engine crank will turnover and start normally. But stop to run and errand or grab lunch...and the warm 302 2 barrel engine will turn over very sluggishly, lke the battery is dying. If you wait until the engine is cool, an easy start is assured but that takes hours! A local repair shop has rebuilt the carb, the battery & cables are new, and the starter works fine when engine is cold. My local repair shop is out of suggestions. It seems to work a little to hold the gas pedal down on the floor for a warm engine start....but engine still turns over sluggishly when trying to start when warm. Now If I drive it.....I just drive it around town a bit then back home ...unless I stay several hours somewhere while the engine cools....but that's not fun. It is a convertible, fun to drive...and this problem needs to be solved.
View 14 Replies
I have a 2000 Jetta that doesn't blow cold AC. Here are the details:
- When the AC is turned on, air does blow through the vents. Each setting (1-4) does blow harder than the previous.
- Both front fans spin and are working
- The AC compressor clutch never engages
- All fuses (two inside the car and the one above the battery) have been replaced and test good.
- When the AC is on full blast, the voltage coming from the AC compressor wire shows ~9.3V for about 5 seconds, then jumps up to about ~11V for less than a second, this repeats over and over and the clutch never engages.
What the next logical troubleshooting step would be? I've read about this possibly being the fan control module (maybe) and also read about testing the AC compressor using an external 12V power supply, but am not sure where to go from here.
View 7 Replies
When engine is cold it starts fine, when hot from driving (e.g. the engine's temperature display's needle is in the middle) i cannot start it unless i try 3-4 LONG keys. What can it be? Where should i start?
View 17 Replies
I own a 2000 Jetta VR6 5 speed. Car has over 300,xxxkm on it, with documented maintenance including chains within the past 12k. Car has intake, 2.5" resonated exhaust, stock software.
I have recently noticed that the car has a cold start issue. Its winter here in Canada, so in the morning when i go to start the car and let it warm up for a couple minutes, the idle is choppy at first and then evens out at around 900-1k rpm. If i try to blip the throttle, or even hold it (half way or WOT) the car just wants to bog out, EXTREMELY rough idle. It will eventually, after about 2 mins of idling, go away and i can drive.
I have absolutely no issue with allowing the car to idle for a few mins to warm up, but i know for a fact that whether a car is cold or not, it should be able to rev freely.
I also have horrible fuel milage. I use 91 octane, and average about 250-300km per tank. 70% city 30% hwy driving.
The following parts have been replaced in the past 1200 to try and resolve the issue
OE Mass air flow sensor
OE spark plugs
BREMI wires
OE Bosch front O2 sensor
I have scanned the car several times, which led me to change the parts i did. Only had a CEL once and it was for the front O2 sensor which i just replaced. Any other codes were for random multiple and a cat efficiency fault. Again those were fault found off a GFF test done at VW, they were not enough to trigger a CEL, but i still changed the parts.
View 3 Replies
Ok, to start off. I have a 2010 2.0T CCTA with 23k miles. I recently purchased a HPA Intake Manifold and installed it myself. I was told by HPA that they offer a tune specifically for their manifold. I however, purchase the Maestro suite by Eurodyne with the intention on getting it all tuned myself. I was able to code out the CEL for the flappers no problem. Now my only issue is the cold starts. During the cold start cycle I get misfires and air surge. I ran the fault reader and got the P0300-P0304 (Misfire faults). Obvious thing to check were plugs and packs. So I changed them. No change.
I read in a bunch of threads that these faults as well as air surge are a sign of the PCV Valve. I have a catch can kit on order so I will see if that wotrks. My guess is no. Another thing I think it could be is the N75 valve however, this issue only occurs during the cold start cycle. After the cold start cycle is done I have no issues what so ever. So I ruled out the N75 valve. If it was bad, then it would be bad regardless of how cold/warm the engine was. I have attached a video of the Cold Start.
View 6 Replies
My GF recently picked up a 1.8t (AWW) and we scanned it with vag com before she bought. We knew it had some misfires and a few other small problems so when it ran at higher RPMs we didn't think anything of it.
Fast forward to now after replacing some parts (hoses, coil packs etc...) and still the RPMs seem a little high compared to my mk4 vr6. On the streets in 4th gear, my car stays around 2200 and on the hwy its probably around 3300 in 5th gear at 75mph.
On the streets, her 1.8t seems normal but on the hwy in 5th gear, she's at nearly 4k. So my question... Do 1.8ts run at higher rpms under normal driving?
View 11 Replies
So my wife drove her car all day yesterday, everything fine. This morning went to start and it wouldn't. It turns over fine just not firing.
Now during the summer I had replace the fuel pump/filter before discovering that was not the issue.
I know you are already thinking CPS!.. I replaced that over the summer.
I have not checked the spark yet, kinda hard to do that one by yourself.
Beyond spark I am not sure what else could be wrong, especially because it was running fine last night. Is it common for accents to have issues in 20 degree weather?
View 3 Replies
2005 gti 1.8t having really rough idle and misfires at idle fine while driving pulling codes:
P0300
P0301
P0302
P0304
Unplugged MAF and didn't make a difference...
View 6 Replies
It all started a few months ago.... I started my car, and it started noticeably misfiring, CEL flashing and everything. I scanned it with my vagcom and it came up Cylinder 1 Misfire and Random Multiple misfire. I popped the hood, made sure everything was seated correctly, and shrugged.
Ordered some new wires for it, since it had 80k miles on it with original wires, I figured why not. The misfire didn't come back.
A few weeks later, same thing happened. Misfires, flashing CEL, same codes. I ended up driving it the 5 minutes to work anyways and figured I'd look at it later after I got off.
8 hours later I started it up again, ran like a champ, no CEL on. The problem didn't come up again for 3-4 weeks.
So now, without fail, every month or so, I'll get the same issue. It doesn't matter if it's raining or sunny or cold or warm. But if I let it sit for a few hours, it'll act like it never happened.
Now, I haven't replaced the coil pack yet, simply because it doesn't sound like a coil problem, but I might do it just for the hell of it. New plugs and wires have already been done.
View 1 Replies
So I bought a used 1.8t back in august. My second golf, up from an mkiii and I love it. However, the previous owner installed a CAI and being that he lives in the desert, probably never had any issues taking on water. Fast forward to my problem, got caught in a rainstorm, limped it home with the CEL and the traction lights on. it died like three times trying to get it home, but it still would idle when I parked it.
Now I've used the search feature extensively on this problem, and what I've down so far is to take off the intake and reroute it about six or seven inches from the maf, I've cleaned the filter, maf, pancake pipe, and SMIC with denatured alcohol and those are all currently drying. When I took the IC off, specifically the connection between the pancake and the IC, a good three cups (~30oz/850sillyliters) of water dumped out.
Again, my car still was idling when I parked it. Scanned the CEL and got misfires and maf low air codes. Before I started tearing down the intake I took the coils and plugs out and put my shop lights above the valve cover to generate a little heat, maybe make a lil water evap from the cylinders. I live in a pretty arid climate, IE all the water that fell onto my garage floor was gone in 24 hours. Prolly wishful thinking but whatever.
My plan next is to put everything back together when it's all dry, pour a lil oil down into the cylinders, and crank it while the spark plugs are out. Hopefully any residual water will shoot out, along with the oil/gas, and I can go back to enjoying my life.
Also, the intake is hot. I'm thinking any water that made it past the intercooler would've been steam/vapor and I shouldn't need to remove that? Also it seems like it's in a conformation that would force any residual water to drain either into the cylinders or back into the intercooler, so I really don't see any gains by removing and cleaning it
View 7 Replies
I have an 03 vr6. I'm getting codes p0300, 0303, and 0304. I changed the plugs and the coils and still has changed nothing. In the morning when I first go to start the car it has a rough start and idles rough. But after letting it warm up it is fine. It drives perfectly fine, no misfires. None of this started happening until the car ran hot a few weeks ago. Did a compression test and everything came up fine. So would could my issue be? I'm at a loss here. I was thinking fuel issue but if it was a fuel issue, wouldn't it run rough all the time?
View 15 Replies
I have an '03 gti vr6 with a miss fire problem. Once it's warmed up is when I notice the problem. Just changed all the spark plugs and now I'm lost.
View 21 Replies
I just recently bought a 03 Jetta and it doesn't shift until it is warmed up, once warmed up it runs great. I was told it needed a transmission change but when taking it to Aamco they said it needed a valve body. I read that it could be the solenoids that are causing the issue. Should I replace the whole valve body or just the solenoids? What is the main components in the valve body?
View 2 Replies
2000 Jetta MKIV ... 2.0L GL
I've been dealing with random misfire codes on my Jetta (P0300, P0301-P0304). I've since replaced the spark plugs, wires, fuel filter, MAF senor, & camshaft positioning sensor but the problem still persists. The misfires occur right on start-up and don't stop which is leading me to the coil pack being bad.
View 6 Replies