Golf IV / Jetta IV :: 2000 - Got Transmission Codes?


Jan 19, 2015

i have a 2000 jetta 2.0 i am in desperate need of a new transmission. Ever since I bought the car I rarely had third gear and today on my way from southeastern PA to northwest Ohio seem to pretty much completely lost first unless I really slam it in and fifth likes to disengage every now and then unless I hold the shifter in place both first and fifth were slowly giving me problems until it got really bad after todays 8 hour drive. My transmission code is EBP, is there any other codes I can put in my car from another 2.0 or do I have to get another EBP?

View 2 Replies

Advertisement

Golf IV / Jetta IV :: 2000 GLS VR6 12v Codes Won't Go Away

Okay I have a 2000 Jetta GLS VR6. I had the engine replaced after i found out the block was cracked when replacing the heater core. ever since it was replaced the car runs great but it keeps throwing these 4 codes.

p1424 secondary air injection system bank 1 leak detected -intermittent

p0411 secondary air injection system incorrect flow detected

p1603 internal control module failed self test -intermittent

p0134 02 sensor bank 1 sensor no1 no activity -intermittent

The thing that is bugging me is that the sai pump is still running. On cold start it literally sounds like a Dyson vacuum. What i should try.

View 1 Replies

Golf IV / Jetta IV :: 2002 - Differences Between The O2J Transmission Codes?

Long story short is that I need to replace the 5 speed transmission in my 2002 AWP Jetta. I believe it has the EHA transmission in it from the factory, but what are the differences between the different transmission codes? Better question, can I swap any O2J transmission into my Jetta?

View 1 Replies

Golf IV / Jetta IV :: 2000 - CEL On / OBD Scanner Won't Read Codes

The past week, the CEL of my Jetta 2000 was on, and a couple of days after, was off. But yesterday was relit. I take my car to Auto Zone to check codes with scanner, but was impossible read any code, the lector can't connect with computer. I thought in fuses, but the fuses are fine.

Searching on google, i found that the reason could be the aftermarket radio, but I am not sure about that, the connections are seen aparently fine. I Read in one thread that disconnecting the aftermarket radio harness is enough to can read codes from computer.

I read also that the scanner could be incompatible with VW cars, but I don't think that, because AutoZone should have a scanner compatible with most of the common cars models.

The fact is that I don't want to get in troubles with the harness of radio, I don't have tools like multimeter neither knowledge about electrical systems, i just want to know if disconnecting the radio harness is enough in order to read codes. (in case of the problem be on the K-line wire).

View 11 Replies

Golf IV / Jetta IV :: 2000 - Engine Light And Codes That State Misfire On 1 And 4

My daughter's 2000 Jetta with a 2L has an engine light and codes that state Misfire on 1 and 4. It is intermittent as it only misfires once in a while.. She is in Rolla MO, and I am in Detroit MI. A couple of years ago the car died when she was home and I found a swollen/cracked coil pack. I replaced it with an aftermarket. The plugs and wires were replaced about 30k ago with OEM parts. I am tempted to have the son in-law replace the coil pack with a Bosch unit.

View 3 Replies

Golf IV / Jetta IV :: 2000 - Transmission Isn't Shifting Gear Until 3K RPM

I come today for a apparently transmission problem. I have an automatic VW Jetta 2000 2.0 that i bought a few months ago, the car is great, has 250K miles.

The problem is in the morning when car is still cold, the transmission isn't shifting gear until 3K RPM (For 1-2 is about 2.5K RPM, and 2-3 is about 3K RPM). After 5 minutes of driving all back to normality and transmission shift gear about 2.2K to 2.3K RPM.

The question is: this is normal?, what could be wrong?.

View 7 Replies

Golf IV / Jetta IV :: 2000 - Transmission Malfunction / 2nd Gear Missing / Gone

So, I recently picked up mt 2000 vr6 has 200k on it runs great well taken care of. I was just driving not getting crazy or any sort of thing. it has ground in 2nd a little from when I got it. I put it in neutral then went to put it in 2nd and it went but nothing there. it will go into 2nd but won't stay and when I hold it in 2nd gear it just revs no noise or anything just sits and rolls. tried doing the reading but all I fold was 1st and 2nd I just have no 2nd.

View 1 Replies

Golf IV / Jetta IV :: 2000 - Transmission To Mount Bracket Bolts Destroyed Inside Trans Housing?

Long story short, over torqued the top two stretch bolts and destroyed the threads. We helicoil'ed both holes and put the bolts back in. That was about 4 months ago.

Today both bolts snapped not while moving. We dolly'd the car home and bought a replacement bracket, however all three bolts along the bottom that go into the transmission housing broke off inside.

I'm a tad stuck at this point. I could drill and tap new holes over the existing, but i question whether that is a good idea. My other thought was to get 3 of the larger stretch bolts that go in the top, completely drill out the three that are broken and tap the big ones in. This thought would also require drilling the bracket to make the larger bolts fit.

View 3 Replies

Accent LC (2000-05) :: 2001 - Transmission Goes Into Fail Safe Mode / No CEL Codes

2001 Accent, 1.5L Automatic with OD, 263,000 km

Transmission goes into Fail Safe Mode but the CEL does not light up and code reader shows no codes. Shifts fine in town,1-2-3-4...4-3-2-1, but on highway when going up inclines (steep), transmission downshifts from Overdrive into 3rd,as i press the accelerator it will downshift into 2nd (as normal), until i reach the top of the incline (3500-4000 rpm) but then as the car levels out on the highway, it will shift back and forth between overdrive and 3rd, (jerky shifting) then finally goes into Fail safe mode, 3000 rpm at 80-90 km/h. Once I shut the car off for a few minutes, the transmission is fine and shifts normally. Fluid levels are good. Why the CEL is not giving code?

View 1 Replies

Golf IV / Jetta IV :: 2001 1.8t - Two Different Engine Codes

I have a 2001 1.8t beetle and doing some research to buy parts I came across two different engine codes. My trunk says I have a AWV engine but the cylinder head says AWM. This is really confusing as looking them up I get three entirely different options for this car.

View 6 Replies

Golf IV / Jetta IV :: Light Comes On Throwing The Codes

I recently had an issue with a coolant leak. the Y shaped coolant line connection went bad located under the power steering reservoir. The car got hot and the coolant light came on i immediately turned the car off and saw coolant leaking out from this.

Now today I start my car it has a rough idle and dies once it dies it doesn't start again and the epic light comes on throwing the codes

17579 P1171 Throttle Actuation Potentiometer Sign.2 Range/Performance

17951 P1543 Throttle Actuation Potentiometer Signal too Low

16497 P0113 Intake Air Temp.Circ High Input

17987 P1579 Idle Speed Contr.Throttle Pos. Adaptation not started

17953 P1545 Throttle Pos.Contr Malfunction

17976 P1568 Idle Speed Contr.Throttle Pos. mechanical Malfunction

18012 P1604 Internal Control Module Driver Error

View 1 Replies

Golf IV / Jetta IV :: 04 - Idling Pitfall With Codes

My gf's 04 gti 1.8t 5spd is having idling issues. Here's the rundown, at idle it sits at 800 rpm but when given a rev it then becomes erratic and fluctuates between 500-1100 rpm. When throttled again lightly it returns to normal 800 rpm idle. The car will try to stall a little bit. Now for the codes and lights. The lights are the traction control light and the check engine light. The codes are p0102 (MAF) and p2181 (coolant system performance). I have recently had a misfire which I took care of with 4 new coil packs. I kept the 3 good ones I took out. I have to change the plugs still but don't think it's an issue. Has new clutch and sits at 148,852 miles.

View 5 Replies

Golf IV / Jetta IV :: 1.8t Won't Start / Throwing 2 Codes

Throwing 2 codes -

P0172: too rich
P1176: post cat 02 reached limit

Last time it turned on it had horrible air flow, it felt as though it was choking. definitely not a misfire. occasionally after spirited driving the engine would die after I came to a complete stop then worsened to cutting off when I put the clutch in at high rpms. also have a slight loss of power. I also recently added a 3" tbe and changed coil packs.

View 4 Replies

Golf IV / Jetta IV :: Car Is Showing Codes For O2 Sensors

This isnt my first vw but its my first vr6, its a 2000 gti glx, only showing codes for o2 sensors havent got a vag com yet only have a obd scanner. It idles fine and runs smooth until i get over quarter throttle then it starts hesitating like there isnt enough fuel or air...i know that the noob owner i bought it from cheaply put exhaust on it and i didnt see any o2 sensors but ive never known a car to not run correctly without them.

View 5 Replies

Golf IV / Jetta IV :: 2.0 Throwing Multiple Codes

So my car has been dropping multiple codes after I scanned her and found all five: p0303, p1128, p0172, p1300, p0301. She is just a simple five speed AEG and has no mods other than a SRI. I already replaced the MAF but that ended up causing more codes and I have checked the vacuum lines to no avail.

View 2 Replies

Golf IV / Jetta IV :: Car Won't Go Into Boost, 2 Error Codes Detected

I was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.

View 5 Replies

Golf IV / Jetta IV :: 1.8T - OBD Readiness Codes Won't Reset After PCV Repair

1.8T ... Failed smog test, then got PCV hoses repaired. Now I'm failing because the OBD readiness codes won't reset. I've driven over 100 miles and the shop that fixed it said to "just keep driving it" but that they have no other solution to get those codes to reset. Any tips to those codes to ready?

View 3 Replies

Golf IV / Jetta IV :: CEL Is On With Codes P0785, P0411 And P1151

Alright I might have made a major mistake and I need some input; I just recent bought a 2001 Jetta VR6 131k on it and at first I didn't notice so much but since I've gotten. To drive it more I've noticed it's really sluggish on take off and doesn't seem to shift into 4th gear. Also I started noticing a faint rattling noise. And the CEL is on with the codes P0785, P0411 and P1151.

View 1 Replies

Golf IV / Jetta IV :: 1.8t Throwing Codes And Misfire - CEL Came On And Blinks

So recently I took my engine apart to do a valve cover gasket and Ecs tuning 2.0 coil conversion. I noticed a good amount of oil in the plug tubes so I got out my trusty soap dispenser and started pumping out oil. Pulled plugs and cleaned them (wanted to make sure oil was all out b4 getting new) also while I had it apart I wanted to take intake off, ( just to polish it and clean out any carbon inside).. Well I never ended up doing that. I removed the injector connections and realized it was to much work for such little satisfaction. So I plugged the injectors back in.

I got my car all back together and now I'm throwing 6 cel codes!! P0102 (maf) which I'm assuming b.c I took it off for so long, p0201, p0202 ( injector 1 and 2 miss), then some misfire codes p0300 (random) p0301 (cylinder 1) and p0304 (cylinder 4). The car starts runs very rough then cel comes on and blinks. I was thinking maybe the oil getting down to the combustion chamber couldn't be the best for it but it would just burn off. Only other thing I did was take off the thottle body and cleaned it.

View 3 Replies

Golf IV / Jetta IV :: Codes P0238 And P0106 - Car Is Not Boosting

My car is not boosting. I had two codes p0238 and p0106...

View 9 Replies

Golf IV / Jetta IV :: Getting Multiple Codes After New Trans Installed

I finished installing an auto out of a 1999 beetle into my 2000 golf. I used the beetle TCM now it wont shift out of 3rd. If I manually start in first it will shift up to 3rd but nothing past 3rd. I had it scanned with a generic scanner and these are the codes. P1780, P1783, P0725. I researched the heck out of this and I'm not sure what to do. Do I need to take it and have a vag com hooked up to make sure the ecm and the new tcm are talking? It seems others have had these issues and I thought it might be solenoids but that's not what's coming up.

View 2 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved