Golf IV / Jetta IV :: 2.0 Motor Burns Oil At Unreasonable Rate
Nov 13, 2015
I have a 2001 Golf with a 2.0L motor. I've had this issue for a while now; the motor burns oil at an unreasonable rate - around a quart every 1200 miles. If I'm at a long traffic light and idling, a lot of white smoke will come out the back when I start moving. I don't notice smoke any other time. Also, the gas mileage is reduced by about 75 miles per tank when it's cold outside.
I have recently replaced:
temperature sensor
thermostat
plugs & wires
cleaned mass airflow sensor
The last mechanic I went to, who I will no longer be using, as he is incompetent, thought the cause for the lost cold weather mileage and burning oil is the PCV valve. A friend thought it would be a worn head gasket. I'm having trouble finding any info on PCV valves for this motor.
View 3 Replies
Advertisement
Well I have been working on my build for about 2 1/2 years. Built the motor for the turbo set up that I had on the car and a few other goodies.
Now the motor turns over with no issue and I have spark. So I know my problem lies in the fuel delivery. My pump tested fine and I have fuel at the rail. So my next guess is the injectors. After trying to start the car I pulled 2 spark plugs out and they where dry. So this proved to me there's an issue here.
Before I go and rip my manifold off and start pulling injectors is there anything I could check first? I'm thinking from sitting that have gotten dirty and clogged.
Looking for wire diagram for the injectors on the vr6?
View 9 Replies
I have a '01 1.8T Jetta with 132k miles that is driven to work daily. I don't take it about 4-5k rpms and don't drive hard in general. Nonetheless the motor still seems to be very hot after I drive it.
Well I always leave the engine running for at least 2 minutes prior to shutting it down. It's starting to get annoying but I am wondering if it's worth getting a turbo timer to continue practicing what I do (assuming it's even worthwhile).
So, just wondering what all the 1.8T folks do. Do you sit and let it run for a few mins and then shut down or do you recommend a Turbo timer?
View 15 Replies
My car has been leaking coolant as soon as you put it in from it looks like the transmission area. Today I filled the car with water and drove it on the interstate to work. The car started getting jerky like it was losing power. So I pulled over and when I did the car shut off. There was excessive smoke under the hood and after removing the oil cap, smoke coming from there also. Tried restarting and it sounds like it just spins. No start. Looked at the timing belt, it's still intact. Put a wrench on the crank pulley and it's turning. What's wrong? Is it a goner?
View 10 Replies
My 1.8t motor is still ticking around 2500-3500rpm. I have changed the oil with 5w-40 mobil1 no even 75 miles on oil change, Brand new oil pump with tensioner and chain. oil pick up tube cleaned and good. new plugs about 75 miles on them as well. Always ran 93 octane (highest I can get at my gas station) Only thing left that I can think of is my cam tensioner is bad.
When I accelerate up to speed it starts ticking but as soon as I let off the throttle it will stop get back on the gas it starts again.
Stockish 2000 gti 1.8t 5 speed. short ram intake.
Is there a way to tell if the cam tensioner is bad? .
View 15 Replies
Okay just installed a newer 24v into my existing 24v VR6 GTI both with 135k. I have heard the motor run before it was pulled and sold to which sounded fine. Upon receiving the motor I put new timing chains, guides, headgasket and new gaskets all around. The timing was right on the mark and I tightened everything up to torque spec and I'm getting this noise which sounds like it's from the timing cover area. A code just popped on which I'm going to scan as soon as I get my hands on one. The car was running great for about 20 minute and I shut it off then turned it back on about 5 minutes later and experiencing these scary noises. I tried pulling each individual coil with no results to get the noise away. What could this be?
[URL] .....
View 3 Replies
I got a new resistor since my last one was in a puddle of water and installed that today and still have no heater blower motor. I checked all the fuses and have power. I sent power to the blower itself and it spins good. So somewhere between the fuse and the blower it isn't working. I need to take the controls out and test for power there. Didn't have time to do that today. What wires to check or where to start trouble shooting?
View 7 Replies
Blower motor has stopped working on my 2008 jetta 2.0. Motor works fine and I have traced the issue back to the fan switch connector which is not getting power. Seems like it should be a fuse issue, but they all seem to check out fine. Not sure where else to look. Is there a relay upstream that could be bad? I have owned since new and it has never been apart.
View 3 Replies
I have 2003 Jetta GLI 24V VR6 original owner right from the showroom floor. Just the other day I was driving to work and all of the sudden the rpm's dropped the oil light came on (Beeping) and the car shuts off. I had just changed the oil several days ago and I know the oil level is correct and I check again and the oil level is correct.
So I started of very easy, like most blogs say "oil Sender"...replaced that and after driving for about 20 to 25 minutes...the same thing. So I also replace the oil pump and after driving 20 to 25 minutes the same thing.
No oil leaks. Oil pan is not cracked. So now I am at a loss. I have owned the car from day one and it is very well maintained.
View 10 Replies
My blower motor in my Jetta recently stopped working. When I turn on the blower it works for 10 seconds or so then slows down and dies. Is this a blower motor or resistor problem?
View 1 Replies
I'm suspecting that my motor mounts are going bad, but I'm not 100% sure. I have a video of the engine movement when slipping the clutch and revving the engine with the e-brake on. [URL]............................... I don't need high performance ones, but don't want to spend a ton on OEM ones either.
View 5 Replies
With 132k on the clock, motor has shutters at idle and rattles under acceleration even though seems pull smoothly otherwise - if that makes sense. Anyway, changed plugs and coil packs all without any results. No codes either from the computer. Shop thinks it could be a timing chain tensioner but after spending as much as I have to this point, can't really afford to just start trying things.
View 8 Replies
What hardware I need to install the passenger side motor mount spacer from Euro Image Tuning. Been sitting on it for a while and cant find the hardware that it came with. Would like to install it, but dont remember what it came with..
View 2 Replies
I just purchased a 2001 Jetta Wolfsburg with the 1.8T, 5 speed, and 169,000 miles. I need to figure out the engine hiccups. The check engine light is on. The car seems to hesitate between 2000-3000 rpm when the motor is lugged (pulling a hill, passing, etc).
I had the codes pulled at Autozone and came up with the following.
P0172 (Bank 1 System Too Rich)
P0300 (Random Multiple Misfire)
P0302 (Cylinder 2 Misfire)
P0420 (Catalyst System Below)
P0455 (Evaporator Emission)
P0411 (Secondary Air Injector Incorrect)
View 2 Replies
Car doesn't seem to want to start when warm.
1.8T AWD, 02J swap, no clutch switch (I can start without pressing the clutch).
Cold start, cranks and starts on a dime, after the car warms up and I've turned off the car, say went for a quick grocery run, the car won't start afterwards.
No cranking, nothing. Fuel pump primes, then not a sound. Everything on the dash lights up just fine. No starter motor noise, no clicking.... nada...
Fairly new starter motor pulled from a junkyard donor. Can't think of anything else.
Last time I got stranded in a parking lot, I gave it a few whacks with a tire iron and the car started just fine. Could it be a bad solenoid?
View 16 Replies
The other day when i wanted to start the car, I found out my battery was death so i decided to ask my buddy to push me and crank it on gear. Car shakes as normal and engine started, but then i heard a weird noise like if something was rubbing. I turned it off and popped the hood. I found my engine leaning forward and toward the passenger side.
So the next morning, I checked the bay again and i found out that it wasn't the motor mount. Motor mount is ok, but then i found a broken bolt that holds the bracket to the block; the one that goes right next to the water pump to be more specific. Also in the back of the block there is a bolt that hold bracket to the block again and the thread whole was enough weak to break when the other bolt failed. So I did some research and i found that there is a solution for the bolt in back of the block.
What I am concerned is for the on the goes right next to the water pump. It seems that it broke the whole thing including the part where the bolt threads go. I just had a shop install I.E connecting rods, new piston rings, and rebuilt the heads. They put a new timing belt kit and all its job required. I think they might have a bit of fault on this since it had to be removed when they did the timing belt kit. Anyways I don't want to think my block will be a junk now because engine is running like a champ, and that would be a bummer.
-Bolt that is broken in two pieces.-
-And where it is attached to the block-
-Part of the engine where this all goes.-
View 19 Replies
I was doing about 65 going up a 7% incline and all of a sudden no power from motor shifted down and kept trying tell 2nd gear and power hit and started accelerating again I know I have a p0420 has kicked on and off with the cluster but could that make this happen?! If not what can make my engine or other parts do this... 2.0 2003 Jetta....
View 4 Replies
I am throwing a code for long term fuel trim being out of whack (code 17560) and I am trying to determine whether the MAF is causing it.
I pulled several redline runs while logging flow rate in vagcom. According to Ross tech's site they suggest that your flow rate should be around 80% of the engines rated horsepower. So approximately 200 g/s. I did several runs and never broke 100 g/s so what I should be seeing or has run into this code before.
View 24 Replies
So as of late, I've noticed something strange while I accelerate at hwy speeds. I'll try my best to describe. Cruising on the hwy at 68 mph in 6th gear at about 3000 rpm. Without downshifting, I press on the accelerator to speed up and the tach (and subsequent engine noise) seems to outpace the actual rate of acceleration.
The tack needle about a second or 2 after pressing the gas pedal moves quickly to about 3300 rpm and then settles down to 3100 rpm.After that acceleration seems normal.I tried it again and same result happened.Later I was on surface streets and tried the same thing but at a lower speed and gear. It seemed to produce a similar result.
My question is, what the heck could be causing this? Clutch starting to go? Car has only 17800 miles. I have a UM Stage 1 tune w/ CTS Turbo intake that has been on for the last 3000 miles. Give or take. I remember burning the clutch 2 times in the past. I don't track or do any kind of hoonage with it.
View 12 Replies
My starter motor in my 2004 Golf 2.0 doesn't engage or spin when it is very cold. By very cold, I mean below 5F.
The battery has plenty of juice, and jumping the battery doesn't work. I turn the key to "start" and nothing happens. When key is in the on position, fans, wipers, etc all work fine. When the car warms up to 20F or so, everything is fine and the car starts.
Here's the funny thing. If I put a little space heater on the driver side floor to warm up the fuse and relay panel, it starts with no issue.
I don't know enough about the interlocks between load reduction, starter motor, ignition switch etc to make a good guess as to which relay (if any) may stick in extreme cold. It's a tough problem to diagnose, because I can only experiment when it gets REALLY cold, when it isn't very fun to experiment anyway. I don't think it's the piggy back harness, because the wipers, horn and fan all work.
View 4 Replies
Recently my GTI has been ticking, but it is only between 1 and 2 thousand rpm. After 2k it runs fine and doesn't make the sound. Local tuner suggested an oil pressure problem (not using the proper oil) but I am using the proper oil. It has been like this for over a month now and nothing has come of it. It is coming from the belt side of the motor and sounds like plastic ticking. Could it be a belt?
View 7 Replies
