Golf IV / Jetta IV :: 2.0 Auto Transmission - Code P0730 Incorrect Gear Ratio
Dec 17, 2015
Just picked up a 2002 golf 2.0 auto for $200. Get the car home start it up and it runs great but... transmission shifts all kinds of funky. Starts in first then shifts to third. If I give it some gas it shifts down to second but has nothing there, just revs. Will not go into 4th at all. Throw my little mac scanner on it some codes come up. Only one that mattered was p0277 if I remember. Do a little search and it comes up as the g68 under the tranny mount. Change that out and had not cel. Still shifting the same but no code at all. Throw my scanner on just to see and get p0730 incorrect gear ratio.
View 2 Replies
Advertisement
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 Replies
Bought a Mk4 1.8T gti last year had only about 75,000 on it and drove it for about 10,000 miles. The check engine light went on about 2 months ago and the code read 3rd gear incorrect ratio. It still rode fine until about a week ago when it started slipping. Brought it to the local transmission guys in my town and got a quote at about $3,000-$3,500 to have the transmission rebuilt. The transmission is a tiptronic automatic 6-speed.
View 1 Replies
Was doing some errands this morning and on the way home the transmission shifted a little strangely into 2nd. I had to let off the throttle for it to shift.
Fluid levels are correct and not burnt with no residue floating with a pinkish red color. Using Schaeffer's All-Trans Supreme.
I have read all of the threads related to the P0732 and the mechanical diode issue. Does the e99 4R100 have the mechanical diode? If not, what else could it be?
I also have the P0500 VSS sensor circuit fault which an old Ford mechanic stated could be related to a bad fuel sending unit which is definitely bad on this truck.
Am planning to go out and clean the sensor on the differential. Speedometer is working properly. I have also noticed what appeared to be a small slip when in reverse a couple of times that I initially attributed to tire spin. Is any of this related? Should I be prepared to rebuild/replace the transmission?
View 13 Replies
I have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 Replies
So I got around and decided to fix my transmission my self. Any way I got the code PO734 from my CE light which is gear 4 incorrect ratio. So some people say its the solenoids that cause this issue, some say its the 4th gear clutch...
So, Is it the solenoid or it could be the clutch itself? Ive removed the 4th gear from my transmission today and it looks intact. No weird damage or physical like damage on it... I just don't know which to do since solenoid job i can do myself which will be about 5 hours minimum....
View 9 Replies
I had the transmission rebuilt a year and a half ago, when I took it in it came up 4th gear incorrect ratio. The guy who rebuilt it said it wasn't the original tranny that came with the car because it was modified to fit in the car. When I got it back, after a couple hundred miles or so, the check engine light would come on for a day or two then go off. When the check engine was on it would get stuck in 3rd gear, once the light went off all was well until the next time. I took it back to the guy who rebuilt it since it was still under warranty. the P1529 code came up for TCM issue. He put some sensors and a chip in and thought it fixed it, no such luck. Finally I had the cash and had it looked at by another shop and the 4th gear incorrect ratio came up as well as the P1529 TCM code. He's suggestion to fix it was to either get a used tranny or rebuild this one again. He believes since it isn't the original tranny that the tranny in there now was for a SOHC engine, not a DOHC engine and that's why the ratio in 4th gear is off and it throws the TCM code.
View 6 Replies
PO730 and P0740 codes at the same time auto transmission slips in 4th gear really bad but not all the time...
View 1 Replies
I'll start this off with a few months ago, I went on a trip and along the way noticed that the car wouldn't get into gear. This happened for a few moments, and solved itself.
Fast forward to a few days ago:
So, my Golf MK4 AUTO 1.6L transmission doesn't want to shift into 4th, sometimes.
One and two are good, but sometimes I get quite a lag in between disengaging 2nd and getting 3rd also.
Furthermore, sometimes I get 4th 'semi' engaging, where the engine is revving too much to be fully in gear, but I get power to the wheels and accelerate (slowly).
I did a VAGCOM scan and got the old:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
I also had a CEL on my dash, which I cleared with the VAGCOM. This removed the light, but of course the error still persists.
I've been reading around, and some people have said the issue is the TCM, but some people have had similar problems and a TCM replacement has not fixed this.
(Just btw, my TCM model is 01M927733LK).
And some people have had good results with solenoid replacements. So, I was thinking of doing a ATF flush, just because it was recommend on some posts, but won't necessarily fix the problem.
Contacted a garage to do this for me (never flushed automatic tranny before) and mentioned the VAGCOM codes, and he said this is a slip code.
So, now I'm not really sure what to do to fix it. Are the solenoids interchangeable? Am I able to switch two gears' solenoids to see if it moves the issue to another gear, proving its the solenoid?
View 1 Replies
My Mk4 GTI has a problem with the transmission searching up and down for a gear, second to third then back down to second and so on. My local dealer wants to put in a temp sensor because that's what the code says but to do so costs almost as much as dropping the transmission. He won't guarantee that will fix the issue so I am inclined to just buy a used automatic and spend the money on a complete replacement. It will probably cost me a few hundred more but seems like a better long term solution. Of course that depends on the used transmission.
View 2 Replies
I got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.
View 4 Replies
2004 VR6 24v ... I had another thread about my son's car stalling after driving about 20 miles and then running good again after letting it sit for a couple of hours. Anyway I changed the Crank Position Sensor and I have been driving it work and back the last couple of days so I am starting to relax that the CPS fixed that problem. Won't be positively sure for a while as the problem took a while to occur. So far so good.
While coming to work today the car picked up the P0411 code, secondary air injection system incorrect flow. When I changed the CPS sensor i unbolted a module underneath the car by the oil filter to get better access to the CPS. I did not remove it, just unbolted it so I could push it out of the way about and inch.
After putting it all back together and driving it for several trips with no stalling this P0411 comes on. Is that module I moved the Secondary Air Pump and could I have disturbed something. I will check it when I get home. How critical is that code. I read where it works to warm a cold engine. What effect would there be driving with that code?
View 5 Replies
I have a 3 spee Od out of a 1985 F-150 2wd . I was wanting to put it behind a Onan 6AT diesel . The engine came out of a P-350 bread truck . I runs great . I was wanting to know what the gear ratios are on the transmission . The engine has about 135 ftlbs of torque . The tranny was behind a 300 6 cyl . Iam trying to find out if this tranny will work or will I have to go to a N<!-- -->WC or TKO 5 speed .
View 6 Replies
I have a 06 f150 and about a month ago I purchased an edge evolution. Twice in the past 3 weeks my o/d light starts flashing and my truck beeps and it shows Trans Fault on the trucks display. When I use the edge to check the DTC it comes back as P0731. I am running the canned level 3 tune no changes and trucks completely stock other then the edge. Also both times I have been going about 10 mph down a hill without giving it any gas. Also both times of shut the truck off and let it sit for a bit to make sure I wasn't going to break something.
View 14 Replies
1999 Jetta MK4 with only 124k miles on it. Everything is fine with the car except when the car shifts from 2nd to 3rd it is jerky/violent/forceful everything else is good with car except check engine light is on but I don't really care about that and I'll go check with autozone to see what the code is. I am able to feather the gas when I know its going to shift and I can make the shift pretty smooth. My question to all the experts is does this mean that this tranny is on its last leg or does it still have a lot of life left in it. My old Cabriolet did it for years and never was a problem.
View 5 Replies
So my daughter's '04 Jetta SW 2.0 will not upshift and has the engine light on. After having it read by the local shop I have the following codes:
P0743 Torque Converter Clutch Circuit Electrical Malfunction
P0743 Torque Converter Clutch Circuit Electrical Malfunction
P0811 Excessive Clutch Slippage
So what to do? I read a lot about issues about the alleged poorly designed/manufactured stock "Auto Trans Valve Body" and how that seems to be a culprit of shifting issues above 150K.
View 7 Replies
So, I have a 2009 Golf City (Canadian mk4.5) with the 09G 6 speed Tiptronic automatic transmission. It's at 80k kilometers and shifting fine, I can remember maybe one 1-2 slip bump a few weeks ago but that's it. Shifts in Drive, Sport or Tiptronic are smooth and forced downshifts are smooth as well. I do want to follow the US service interval of 40k miles, and of course, my dealership won't do anything with this transmission unless it's broken because "Your fluid lasts the life of the car sir!" That, of course, we all know is BS because every transmission wears, and I don't want millions little metal shards of hardened steel having a party on the inside of my transmission.
This being said, I know that you can do a pan out filter and fluid change, but your only getting about 5L of fluid of the 9L that the 09G has. Or I can pay a local trans shop to do a full flush without dropping the pan by tapping into the in/out fluid ports and flushing everything out. My worry about a flush is that it will take these little anarchist metal shards and put them in a spot where they get stuck and have an all out project X-style party with my solenoids, gears, and torque converter. And the filter still won't have been changed!
Or I do the former where I get the ECS Tuning kit, drop the pan and clean out these little bastards and put in a new filter and not worry about the last 4L of fluid that still might have some of these buggers in it...
View 1 Replies
I have an 04 jetty with an auto Transmission. It doesn't seem to shift after the first time when speeding up. What might cause this?
View 5 Replies
I need to take the tranny (automatic) off the old engine (BEW).
What are type/size are the bolts connecting the tranny to the block?
The 2 bottom ones I got out using (assuming) 10mm (?) triple square.
What size (socket/tool) and type (triple square, torx, allen) are the others?
View 1 Replies
Having problems with code p0169 incorrect fuel composition, I got this code today but I've felt like I've been having problems with it since I did the stage 1 update a few months ago before the update I was running the 93 octane setting and after the update it would rev up quite high when I first started the car so I switched to the 91 octane setting and I felt like every once in a while power would kind of bog down until today it finally popped this code and the epc light was also turning on and off, it also felt like the car was misfiring. My car won't rev up past 4K rpm....
View 1 Replies
Check engine light came on the other day. Brought the car over to autozone and this was the code that came back. P0441 EVAC Control System; Incorrect flow. Where I should start looking?
View 3 Replies
