Golf IV / Jetta IV :: 2.0 AVH - CEL Flashing And Random Multiple Misfires
Nov 2, 2015
It all started a few months ago.... I started my car, and it started noticeably misfiring, CEL flashing and everything. I scanned it with my vagcom and it came up Cylinder 1 Misfire and Random Multiple misfire. I popped the hood, made sure everything was seated correctly, and shrugged.
Ordered some new wires for it, since it had 80k miles on it with original wires, I figured why not. The misfire didn't come back.
A few weeks later, same thing happened. Misfires, flashing CEL, same codes. I ended up driving it the 5 minutes to work anyways and figured I'd look at it later after I got off.
8 hours later I started it up again, ran like a champ, no CEL on. The problem didn't come up again for 3-4 weeks.
So now, without fail, every month or so, I'll get the same issue. It doesn't matter if it's raining or sunny or cold or warm. But if I let it sit for a few hours, it'll act like it never happened.
Now, I haven't replaced the coil pack yet, simply because it doesn't sound like a coil problem, but I might do it just for the hell of it. New plugs and wires have already been done.
View 1 Replies
Advertisement
So I picked up this 24v vr6 in florida and it has the folowing codes:
p2181 malfunction in cooling system
p0303 misfire in cylinder 3
p0305 misfire in cylinder 5
p0300 random multiple misfires detected
p1570 engine control module disabled
I am thinking the ecu is fried? otherwise why else would that last code pop up. misfire codes im assuming are related to the ecu because theres new COP on each cylinder, newer starter, newer alternator, new spark plugs. Cooling system malfunction im thinking could be the ECT sensor, apparently the water pump was replaced a little while back.
If the ecu is fried can I buy a new one chipped from like APR or do they need the existing ecu and then they modify it?
View 5 Replies
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 Replies
I know the ignition coil are a big thing but I'm going to be buying this car this week and so I need to see how much less to offer the guy because of this issue. Is there anything other then the ignition coil that it could be? What's worst case scenario? And also would it be ok to drive it home about 60 or so miles with this going on? I'm guessing it's doing the misfires at idle.
View 6 Replies
just picked up this 99 Jetta with about 150,000 miles and while driving all of a sudden i had extreme power loss, shaking and shuddering, and the engine light came on. My code reader found multiple random misfires cylinder 1 and 4 codes P0300, P0301, and P0304.
View 7 Replies
So I took a trip from Dallas to Florida, and on the way back my check engine light came on. The car shakes at idle, almost like it wants to take off. I drove it back to Dallas like that since the car runs normal on the high way. I got it scanned at autozone and the code said it had multiple random misfires. I'll be taking to the dealer in the morning, but what it could be? The car jumped over 50K during the trip hopefully the dealer will be nice and cover it.
View 4 Replies
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
View 7 Replies
2000 Jetta MKIV ... 2.0L GL
I've been dealing with random misfire codes on my Jetta (P0300, P0301-P0304). I've since replaced the spark plugs, wires, fuel filter, MAF senor, & camshaft positioning sensor but the problem still persists. The misfires occur right on start-up and don't stop which is leading me to the coil pack being bad.
View 6 Replies
I left the key on and drained my auxiliary battery(It was weak before) and when I jumped it it started and then shut off after ~20 seconds. I tried various different things and all I succeeded in doing was draining my HV battery from starting it so many times. So I disassembled the pack and recharged it and now it starts and runs but it is misfiring. It throwing 4 codes:
P0300: Random/Multiple Cylinder Misfire Detected
P0302: Cylinder 2 Misfire Detected
P0304: Cylinder 4 Misfire Detected
P1305: Ignition Coil 2 Primary Feedback Circuit
I inspected the igniters and plugs and they seem to be OK and I'm not sure where to look next. I'm not sure if the battery issue is related or not but I did replace the auxiliary battery.
View 11 Replies
I have a 1999.5 Jetta VR6 12v, last week the car would not start. After some tests I determined the coil pack had gone bad. Replaced the Coil with a brand New aftermarket German made coil. Now 1 week later, driving at highway speed CEL came on, started to flash and obviously misfiring again. Ran Codes and now im getting these DTC's:
1)random multiple cylinder misfire detected p0300
2) cylinder 4 misfire detected p0304
3) ignition coil output 3 electric malfunction p1395
4) cylinder 3 misfire detected p0303
has this new coil gone bad already after a week?
New issue?
Plugs were replaced less than a year ago, wires were apparently replaced by previous owner about 2 years ago now. Crank sensor replaced less than a week ago...
View 10 Replies
The vehicle is a 2004 Jetta MK4 1.8t.
Last thing I had replaced about 2 months ago was the Solenoid valve, the MAF and Solenoid hose. Car ran fine for about a month, and bam...engine light came back on, along with the ASR light. At first it was saying "cat converter" so I researched that, and what a surprise, it spoke about being a $1k piece to replace. NOTHING HAS BEEN CHEAP ON THIS CAR, and I'm losing my mind.
The latest adventure happened today coming back from the gym. Car started jerking (which has been normal since every now and then the ASR light will come on, which I'm told is the traction control light. Causing the car to jerk. Simple fix is pulling over, shutting the car off, and turning it back on. That always clears it, and then I'm back on the road.) but instantly it lost power. It wont shift, but the traction control light didn't come on. I plugged my OBD2 tool up, and came back with these fault codes:
P0420: Catalyst System Efficiency Below Threshold (Bank 1)
P0753: Shift Solenoid "A" Electrical
P2637: Torque Management Feedback Signal A
I'm going to go to these guys tomorrow, but I would just like to get an educated guess on what might be going on, so I don't look like a lost dog while they're figuring out what to do next. These guys seem knowledgeable, but they're missing something since I've been in and out of their shop several times and still getting my traction control light on at random times, and now all 3 of these codes.
Does that Solenoid code have anything to do with the Solenoid valve they put in? I was told that cleaning the throttle body and the cat converter might work. Would those be cheaper options to consider, and see if that works?
I also read that unplugging the alternator and plugging it back in, then cleaning the male and female with electrical cleaner might work. I was told about a month ago that my battery barely passed. Could this be causing any of my issues? I also did a log while I was driving, but all that's showing up is a google map document.
View 7 Replies
I have a 2004 Jetta 1.8t 6speed, I recently bought it from a person(my first VW ever) so just trying to fix some things on it, One thing that I'm stuck at is My CEL, it keeps flashing the code P0501 and some random misfire on my cylinders, I have reset it and they keep coming back.
when I put about 10-15% throttle it revs up fine, no misfire or hesitation until the fuel gets cut off around 5500, which is 1k below factory red line, does not hit a thing like the rev limiter where it pegs off the top multiple times just fuel cuts off.
If i put anything above the said pressure the car then begins to misfire and lots of hesitation and that's what causes those codes to go off.
I've been reading many things pointing towards the engine speed sensor or the wiring. Occasionally my fuel/temp gauge quit working but I believe that is a separate issue all together.
So really trying to narrow down what is actually causing my engine to hesitate at low rpm.
Also i might note when I'm in neutral I can go wide open throttle and the car revs fine until the cutoff and only does the bog down when it's under full load. It sorta feels like the possible misfire is due to bad air/fuel but really do not know.
View 7 Replies
I am getting random misfires on cylinders 4, 5, and 6. Mostly on 6, less on 5, and even less on 4. Cylinders 1-2-3 show ZERO misfires. I am using vag-com to monitor these. Mostly doing it on idle, cruise seems fine but occasionally when shifting I feel it when engaging the next gear. It doesn't buck but I feel a little hesitation. Cruising and accelerating I do not feel it. Its very strange. A couple times during extended idling I have even gotten a flashing CEL. Fuel mileage has been pretty bad ever since I got the car in December. Average tank gets me 250-270.
I tried swapping coils with 123, and the problem stayed on 456. Coils are all new since I got the car. Plugs are fairly new (under 5K) and I pulled a couple to check, they looked fine and gap was about .028. I might try a new set but my gut is telling me the problem is some where else. I would like to verify/test grounds but I don't know where the harness grounds out.
I also want to get a vacuum gauge on the FPR, or check fuel pressure at idle. I replaced one cracked vacuum line, i am thinning there might be others since there seems to be miles of vacuum line on MK4's. Also have a new fuel filter to install, mine appears to be OEM and the car has 97K.
View 8 Replies
Car: 2011 VW GTI MkVI
Mileage: 79k
Configuration: Stock
Warranty/Coverage: None
So I started my car last Monday and the check engine light was on. Didn't think much of it because the car ran fine and there were no immediate symptoms. I was busy with work this week, but noticed some changes in the car's performance over time so I waited till Thursday to have it scanned at AutoZone, which threw the following codes:
P 300 Definition: Random Engine Misfire
Explanation: Lean air/fuel ratio
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 302 Definition: Cylinder 2 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
P 303 Definition: Cylinder 3 Misfire
Explanation: Vacuum leak on engine
Probable Cause: Ignition system misfire condition, Fuel injector fault, Engine mechanical condition
Prior to making any purchases I noticed that I started losing some pickup, primarily in lower gears between 2-3k RPM's. Praying that it was somehow just the coils/plugs I bought the R8 pack for both and replaced them this evening. Engine starts up and continues to misfire. I have not had a chance to have it scanned but it would appear it isn't the plugs or coils.
When the plugs were removed, there was an 'oily' substance on the threads, which also seemed like it could have been burnt off fuel or oil pushed up from the cylinder. Also 2 of the plugs seemed looser than the others and didn't feel properly sealed. New R8 install included proper plugs for STOCK application, as I do not run any tuning, and i installed with the appropriate plug grease added lightly to the threads.
I took the car for a spin with the R8 coils/plugs installed to compare it to how the car was doing prior the install. Car misfires and seems fine (relatively) at idle and revving to 2-3k rpm yields NO change. It is almost unable to accelerate up a hill, or go past 30 MPH without the car shaking and any gear higher than 3rd seems not drivable. I feel these are my potential diagnoses before i bring it somewhere and have it looked at.
In Order of Most Likely:
1) Fuel Injectors
2) Air Intake
3) High Pressure Fuel Pump
4) Electronic Leads for the Coils
5) Battery Needs Changed
6) Chain Tensioner Failure
7) Coils and Sparks are all Bad, and I am an idiot
I would prefer to do this work myself and can afford the parts. I just didn't want to be fooling around all month without a mode of transportation to get to and from work.
View 12 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
I was driving the car normal with no problem. Got to a red light stop an as I was coming out of the red light the car started to hesitate a bit. So I start to drive home as I was driving home my check engine start to blink and then it stay on. When I got home and park the car I shut off ,then start it up again then the check engine light was off but the hesitation was still there. Then I got my computer and got the vagcom and got this code :
16684-random/multiple cylinder misfire detected
P0300-008- implausible signal
View 5 Replies
Car was taking 3-4 seconds to turn over when I started it one night. After that, flashing CEL and then CEL stayed. Car idles ridiculously rough, thought it was just a coil pack but seems to be a lot more. What is going on with my car?
Performance mods:
APR intake (stage 1&2)
SPM track edition turboback
Stage 2 revo software
R8 coilpacks and NGK plugs put in 9-10k miles ago
Have 52k miles on the car if that matters
View 24 Replies
2005 prius. the car is pulling three codes misfire cyl1, misfire cyl2, and multiple misfires. The car has over 450000 miles on it and runs like a dream. I just replaced they spark plugs and the coil packs in each cylinder. The cel codes are still there after clearing them. I am willing to replace the fuel injectors but just seems weird that two of them would go out like that together.
View 4 Replies
I have a 2000 lc 1.5l ... I just rebuilt the motor machine shop work and all it Will start and run for 3 seconds and then die. If I hold the gas pedal it will run but sound rough and as soon as you let go it dies I have been able to get codes multiple misfires, misfire cylinder 1, misfire cylinder 2, and misfire cylinder 4 I have put brand new plugs (copper core ngk), wires coils, crank sensor, cam sensor, iac, tps, maf and the injectors all have new orings it also has ntk o2 sensors that might have 1000 miles on them...
View 1 Replies
I have a 97 Pontiac Grand Am GT 2.4L Quad 4, my problem is that it misfires and the engine runs rough. You can smell fuel, but there is no fuel leak. I have about 155k miles on the car, never had no serious issues with the car, the car has been great, I’ve owned it since early 2000. Little history on the parts I’ve replaced this year is the following spark plugs x3, spark plug boots x2, timing chain, Timing chain tensioner, camshaft positioning sensor, throttle positioning sensor, fuel pump, fuel filter, air-intake manifold gasket, throttle body gasket, IAC, ignition coils, ignition coil housing, ignition coil wiring harness, swapped the Ignition control module, checked the fuel injectors for solenoid clicking, replaced water pump, thermostat, swapped EGR’s.
Maybe some other parts I can’t remember but I have done a lot trying to figure this out. Also took it to a garage and told them what I have done and the first place they looked was the fuel pump and said it tested at 20psi and called for 40-60psi so they replaced it and problem was still there. They had it for a week and half and couldn’t figure this problem out. Thinking about replacing the ignition coil housing again just to see maybe bought a bad one. Also done the three checks for head gasket blown, milky white oil, anti-freeze bubbling from the reservoir and compression check, all checked out fine. Ran gunk fuel injector cleaner through it several times.
View 6 Replies
My old pump wasnt building pressure so i put a new filter on and i switched wit a used one from an old car i had.key on engine off Pressure goes to 45 then instantly starts droppin? Once i turn key an do again same thing... Car is starting tho. fuel Pressure around 38 while idling. I pulled fuel rail up and looked for leakin injectors.. There was none yet pressure still bled down kinda quick. I also have my cat aloose to keep from messing it up any further. Only codes keep showing is po300 multiple misfires.
View 2 Replies
