Golf IV / Jetta IV :: 1.8t - Idles All Over The Place And Boost Gauge Bounces
Feb 27, 2016
I own a 2004 Jetta 1.8t, about 6 months ago i had an oil leak problem and a cracked vacuum line. i fixed the oil leak and fixed the cracked line with 034 motor sports pcv hose kit. I snapped 2 more vacuum lines and repaired them with rubber hose. p0300, p0301, p0507, p0171, p0303. Are the codes I am currently having actually have had them for just over 6 months. I've replaced all plugs, I've upgraded to ecs tuning 2.0 coils. No fix, went back to oem coils which I am using now. It runs pretty good until i clear the codes. Then idles all over the place and the boost gauge bounces all over.
View 16 Replies
Advertisement
My car is a 2001 Jetta 1.8t. the car is bone stock, I can not hold boost and it fluctuates all over the place. the dv sounded like a flutter until I bypassed the n249 now it sounds like a steady pssh. car still would only make 4lbs of boost and drop to 1-2lbs after 3500rpm. I pulled the line off the n75 to wastegate and did a pull. it boosted to 8lbs spiked to 15 and held 4lbs, if the tires spun it would spike to 12-15lbs and drop to 4 again. I replaced the n75 today and now will still spike high if I spin, with traction boosts about 8lbs which I believe is stock but then drops to 1-2 lbs then up to 4 down to 1-2 sometimes up to 6, it seems random. I also pinched off the dv to see if that was the problem but same thing.
I'm wondering how my car could lose boost with the wastegate actuator unhooked, I can not find a boost leak(not saying there isn't one, but haven't found one), the car holds more boost with the n75 unplugged and under acceleration, with n75 plugged in it seems like 3 surges per gear?
Car throws one code p1473 its an evap code.
The wastegate sounds like its closing when I pull the rod and let it go, lots of tension on it.
View 16 Replies
Okay, here's the car
AWP 1.8t mk4 GTI.
- stock DP
- Forge 007 splitter adjusted 25 clicks
- Swiss cheese stock intake with k&N high flow
- APR stage 1 93 tune.
My boost gauge is currently reading peak of about 15-16 psi. I replaces some vacuum hoses that appeared to be worn, and to no avail. I have no CEL, and no codes thrown at all. This sound like a boost leak.
View 3 Replies
Bought a 1.8t 04 gli. Was boosting 15 pounds so i did a boost leak test. Found pcv up hose from valve to y pipe at valve cover was almost blown in half, so i replace all of that stuff with oem.
Boost leak test again, found where boost gauge is hooked up to, turbo outlet to n75, the hose was leaking, i fixed that.
Boost leak test yet again, n75 was not clamped down, so clamped that.
Boost leak test one last time, held 10 psi before blowing the cap out of the intake. Which is pretty dangerous, my cap is made out of a spray can cut in half. Sounds like a canon. Anyways i heard zero leaks.
So now I am boosting 18psi and holding perfectly fine. Why I am showing ZERO vacuum on my boost gauge??
View 6 Replies
I opened up my hood and now it doesn't close... it seems like the latch isn't locking into place and holding the hood down. I do a lot of car work myself, but after countless hours of trying to figure out why my latch isn't locking shut, I give up. I am planning to take it to a local dealer after I schedule an appointment, but that means that I can't drive for a few days... maybe weeks if they are booked... I don't want the hood to pop up on the highway or anything.
View 24 Replies
So popped my plastic shroud off to change my oil and thought it was strange the the hose for the boost gauge was really oily. Is it normal?
View 2 Replies
I live in Scotland so have a right hand drive 2003 MKIV R32. I got a VF stage 1 kit fitted last year and now I want to fit a boost gauge. I've bought a NewSouth indigo 0-30 psi gauge and a column pod.
What I need to know is where to take the feed from, where is the best place to fit the vacuum tube to get the best readings? any photos would be good.
I plan on fitting it this weekend along with my oil pressure gauge.
View 4 Replies
I purchased a P3Cars gauge and an analog boost sensor with an ECS boost tap. I seem to be getting some fluttering noise at higher boost (greater than about 15 psi).
It was my understanding that digital boost gauges didn't buzz, so I thought I high have some movement of the boost sensor, hose, or the interface box for the gauge. I've got these pretty well padded and fixed with zip ties.
Do I need to get an inline restrictor (cotton swab, filter or otherwise) to eliminate this fluttering noise?
View 11 Replies
I ordered the gauge kit, installed it with the printed out DIY (CIMs)
Looks great, everything is tight, no leaks. All power going to the gauge (even the dimmer).
When power is connected via the plug in the back of the gauge, the needle goes from -30 to 30, full swing like some newer vehicles, not when the car is turned on.
Here's the problem, is doesnt read anything. Sits at -30 at idle, rev (limiter) and under load. The DIY says it should be somewhere around -20 at idle.
The only thing I can think of is the pressure sending unit is broken. I know faulty equipment is not uncommon and I'm not mad if that is the case as long as it gets resolved, I just want to get this thing working. This is NOT a bash against CIM either, I don't want anyone getting the wrong idea.
Also, I used a forge boost tap. Everything tight, and secure, no leaks going to the filter, or the 4" hose from filter to psi sending unit. Did I miss anything that's not in the write up? Early 11 model DSG MKVI
View 6 Replies
I installed a VF intake a few weeks back and noticed my car is peaking at around 14-15 PSI max according to my boost gauge, when it used to hit 17 peak. I'm not sure if I may have a leak nor have I checked it via vag-com.
It does feel a bit off, but for as far as I know the gauge could be messed up now.
Just wondering if there would be any immediate signs (sounds etc...) of whether there would be a leak, or what other problems may cause this.
View 2 Replies
My boost gauge is bouncing around during the flutter at peak psi? I have a apr stg 2 evoms intake and full tbe exhaust 42dd...
Here is a exact video of the flutter i am talking about [URL] ....
View 13 Replies
Recently ran into an issue where my boost gauge stopped reading correctly and makes a weird buzzing sound under acceleration. (Whenever I am generating positive boost).
View 2 Replies
I have a 1979 Chevy Camaro and whenever I turn the car on so it only lights up my dash, my RPM gauge goes all over the place, and the engine isn't even turn on yet. And also before i even put the keys in the ignition, the RPM is sitting at 10.
View 3 Replies
my car into VAG COM and since then it hasn't boosted past 4 lbs. it has Revo stg 2, K04, aftermarket side mount, full exhaust and a couple other bolt ons. Before the car was spiking at around 23/24 lbs. after pressure testing the system I found that the turbo inlet pipe was lose, so I tightened it. Still no change. I tried holding the battery terminals together for 10 minutes to reset the ecu and I also tried clearing the codes through a handheld code reader. No codes even come up anyways for this. The car is a 1.8T.
View 4 Replies
I have a 2003 2.0 gas Jetta (181k miles, automatic.) that won't rev over 3k, starts rough, idles rough and wont stop setting a P0341 cam position sensor code.
The car was not running when i got it, i replaced the coil pack and it ran but not over 3k. Cleared codes, it sets the P0341 immediately.
Had timing belt, water pump, tensioner and cam pos sensor replaced. Still, sets p0341 code, starts rough, idles rough and wont rev over 3k.
The throttle servo makes a little noise when actuated, shop thinks this is my demon - suggests replace throttle body.
View 7 Replies
So I bought a used 1.8t back in august. My second golf, up from an mkiii and I love it. However, the previous owner installed a CAI and being that he lives in the desert, probably never had any issues taking on water. Fast forward to my problem, got caught in a rainstorm, limped it home with the CEL and the traction lights on. it died like three times trying to get it home, but it still would idle when I parked it.
Now I've used the search feature extensively on this problem, and what I've down so far is to take off the intake and reroute it about six or seven inches from the maf, I've cleaned the filter, maf, pancake pipe, and SMIC with denatured alcohol and those are all currently drying. When I took the IC off, specifically the connection between the pancake and the IC, a good three cups (~30oz/850sillyliters) of water dumped out.
Again, my car still was idling when I parked it. Scanned the CEL and got misfires and maf low air codes. Before I started tearing down the intake I took the coils and plugs out and put my shop lights above the valve cover to generate a little heat, maybe make a lil water evap from the cylinders. I live in a pretty arid climate, IE all the water that fell onto my garage floor was gone in 24 hours. Prolly wishful thinking but whatever.
My plan next is to put everything back together when it's all dry, pour a lil oil down into the cylinders, and crank it while the spark plugs are out. Hopefully any residual water will shoot out, along with the oil/gas, and I can go back to enjoying my life.
Also, the intake is hot. I'm thinking any water that made it past the intercooler would've been steam/vapor and I shouldn't need to remove that? Also it seems like it's in a conformation that would force any residual water to drain either into the cylinders or back into the intercooler, so I really don't see any gains by removing and cleaning it
View 7 Replies
So my 2001 1.8t Golf is having some issues holding boost. I have a Gonzo stage 2 tune, CTS FMIC, Forge 008 Diverter, Silicone inlet and MagnaFlow Exhaust. I've also done the whole Evap, SAI delete and installed a catch can.
Starting in 2nd or 3rd at WOT the car spikes up to 18psi and then progressively loses boost throughout the rev range. Close to redline the boost drops to 5 psi or so. It seems to be dependent on the revs. In fifth gear the car holds 18 psi much longer as the revs don't increase as fast.
There are no CELs. I've done multiple leak tests starting at the air box and plugging the pcv/catch can system as well as at the compressor side of the turbo. None of the tests revealed a leak anywhere in the intake system. However, when I stuck my ear very close to the valve cover I could hear what sounded like a very small air leak coming from inside the valve cover. I took a look at the wastegate actuator and it seemed fine, no play in the rod, no loose bolts and to move it just requires enough force to compress the spring and it returned to its original position.
My thoughts are that it could be a fueling issue or turbo in the process of dying maybe.
View 9 Replies
Just noticed today that I have a slight drop in boost. Normal boost is 1.5 bar but today it is running slightly lower boost and does not have the same pull through all the gears.
2001 mk4 1.9 tdi golf
View 4 Replies
I just recently notice a whistling noise when I hit boost. I'm not sure but it sounds like it is coming from my gauge. I'm not losing boost pressure. I do have a glow shift gauge. The most recent install was the TIP which I clamped on to the turbo but I'm wondering if it isn't on tight enough.
View 2 Replies
I was riding along today everything running fine then I came to a stop sign and when I pulled off my car wouldn't run 10 psi of boost it was only running 5 psi so I when to a buddys checked everything over and all my piping looked fine so I went up the road and everything was fine so when I started going home it did the same thing pulled of shut the car off pulled off and it was fine again.
View 5 Replies
I think my stock DV is going bad, my car makes a weird noise under boost?
1. Only happens when first starting the car after it has been sitting for an hour or a few. (not overnight)
2. Does NOT happen when first start in morning.
3. Goes away after like 5 minutes every time and the normal WHIIISHH sound comes back like it should when I step on the gas.
4. It does not make the sound at idle.
This recording I made was of my car being revved up after it sat for one hour.
[URL] ...
View 12 Replies
