1.8T ... Failed smog test, then got PCV hoses repaired. Now I'm failing because the OBD readiness codes won't reset. I've driven over 100 miles and the shop that fixed it said to "just keep driving it" but that they have no other solution to get those codes to reset. Any tips to those codes to ready?
View 3 RepliesSO my car since i have replaced the stock air-box tubing hasnt thrown a code in over 300 miles, and usually it came back within 100 miles.... so i assumed all is well, but nope! i drove it to the inspection place again and it wont read at all so they said readiness isn't set yet, is their a way i can have some1 in nj with vagcom come down and meet me at the place in bound brook nj and set its readiness right there??????? anyways i dont know what to do this is getting tedious and expensive.
View 13 RepliesIm switching out the bulbs on the front turn signal light today, I reach my fat little fingers in there and can barely pull off the wire harness that goes into the back of it. When I did this the wire coverings on all three wires just disintegrated I would guess from the heat inside the headlight. Wel there's a short from where they are touching and my signals don't work at all. my question is I can hardly even reach my fingers down in there too remove that wiring harness ( which is the shortest wire ive ever seen) is it necessary for me to remove the grill the front bumper and each headlight in order to access the wires better?
View 5 RepliesSo i hit a pretty nasty manhole on the road which hit my driver side lower control arm and caused my passenger seat and curtain airbag to deploy. no damage anywhere else. I got the airbags replaced (seat is being reupholstered atm) so i was wondering is it possible to reset the log or do i have to get a new sensor.
View 3 RepliesI am having problems with ALL my driver door electronics, except the fuel door. my passenger side works fine, sunroof works fine. Ive removed the door panel to look for obvious problems, like broken wires.. Fuses are good, looking for a good place to start. Power winder/locks.
Little update, i reset my battery and they worked, waited like twenty minutes, nothing works again.. why would i have to reset the battery every time for the windows to work?
Whenever P0411 triggers for me, it is very late into driving (i.e. like 30 minutes into the freeway type of situation) where the engine has already hit optimal temperature. I've gone 1000 miles after reset before it triggers. Sometimes 200 or so miles, but it never triggers quickly after a reset. I'm unsure if it matters, but the VR6 does have a cold air intake (and I do have the breather hose connected & maf correctly connected). I'm pointing it out because p0411 became an issue about 500 miles after I had installed the cold air intake.
View 6 Replies2003 Jetta GLI 2.8L 24v VR6 .... Last night I went to a friends house, everything was normal on the way there, probably 35-40 degrees out. When I got to his house and shut off the car and pulled the key out the power died (clock/trip meter reset) and the alarm started going off. It has done this before once or twice but I could never figure out what it was and it was never really an issue except for the clock resetting.
Jets won, went to leave and the car wouldn't start. It was raining gently at the time but the car has weathered worse. I replaced the battery ~2-4 months ago so it should definitely still be good. Jumped with my friend's car, started on the first try. I let it sit for a bit then we were on our way.
1/4 mile away in the middle of an intersection the car died, power steering, everything, and I had to drift to the other side of the road. The person across the street from me was a cop and it was 12:30 in the morning but he was gone before my car died. I have been driving 5/6 speeds all my life and I know I didn't cause the stall out. The dash lights flickered and dimmed. I shut everything off and then gave it a try and the car started right up. Revved the engine a few times, reverse and drove away. It was fine the rest of the way home.
The battery connections are tight. The car has started every single time up until now with the new battery. My old battery did leak some acid on the copper connectors and into the main positive power cable but I neutralized all of it and cleaned it off and it looked fine except for some pitting on the outside of the terminal clamp. The car is mostly stock except for the exhaust but that was years ago.
Current Battery Voltage: 12.37 ... I just started the car for the first time this morning and it started perfectly. started @ ~1200 and then settled down to ~800rpm after a bit, it usually does this when its cold out. No codes have been thrown.
Okay I have a 2000 Jetta GLS VR6. I had the engine replaced after i found out the block was cracked when replacing the heater core. ever since it was replaced the car runs great but it keeps throwing these 4 codes.
p1424 secondary air injection system bank 1 leak detected -intermittent
p0411 secondary air injection system incorrect flow detected
p1603 internal control module failed self test -intermittent
p0134 02 sensor bank 1 sensor no1 no activity -intermittent
The thing that is bugging me is that the sai pump is still running. On cold start it literally sounds like a Dyson vacuum. What i should try.
I have a 2001 1.8t beetle and doing some research to buy parts I came across two different engine codes. My trunk says I have a AWV engine but the cylinder head says AWM. This is really confusing as looking them up I get three entirely different options for this car.
View 6 RepliesI recently had an issue with a coolant leak. the Y shaped coolant line connection went bad located under the power steering reservoir. The car got hot and the coolant light came on i immediately turned the car off and saw coolant leaking out from this.
Now today I start my car it has a rough idle and dies once it dies it doesn't start again and the epic light comes on throwing the codes
17579 P1171 Throttle Actuation Potentiometer Sign.2 Range/Performance
17951 P1543 Throttle Actuation Potentiometer Signal too Low
16497 P0113 Intake Air Temp.Circ High Input
17987 P1579 Idle Speed Contr.Throttle Pos. Adaptation not started
17953 P1545 Throttle Pos.Contr Malfunction
17976 P1568 Idle Speed Contr.Throttle Pos. mechanical Malfunction
18012 P1604 Internal Control Module Driver Error
My gf's 04 gti 1.8t 5spd is having idling issues. Here's the rundown, at idle it sits at 800 rpm but when given a rev it then becomes erratic and fluctuates between 500-1100 rpm. When throttled again lightly it returns to normal 800 rpm idle. The car will try to stall a little bit. Now for the codes and lights. The lights are the traction control light and the check engine light. The codes are p0102 (MAF) and p2181 (coolant system performance). I have recently had a misfire which I took care of with 4 new coil packs. I kept the 3 good ones I took out. I have to change the plugs still but don't think it's an issue. Has new clutch and sits at 148,852 miles.
View 5 RepliesThrowing 2 codes -
P0172: too rich
P1176: post cat 02 reached limit
Last time it turned on it had horrible air flow, it felt as though it was choking. definitely not a misfire. occasionally after spirited driving the engine would die after I came to a complete stop then worsened to cutting off when I put the clutch in at high rpms. also have a slight loss of power. I also recently added a 3" tbe and changed coil packs.
This isnt my first vw but its my first vr6, its a 2000 gti glx, only showing codes for o2 sensors havent got a vag com yet only have a obd scanner. It idles fine and runs smooth until i get over quarter throttle then it starts hesitating like there isnt enough fuel or air...i know that the noob owner i bought it from cheaply put exhaust on it and i didnt see any o2 sensors but ive never known a car to not run correctly without them.
View 5 RepliesSo my car has been dropping multiple codes after I scanned her and found all five: p0303, p1128, p0172, p1300, p0301. She is just a simple five speed AEG and has no mods other than a SRI. I already replaced the MAF but that ended up causing more codes and I have checked the vacuum lines to no avail.
View 2 Repliesi have a 2000 jetta 2.0 i am in desperate need of a new transmission. Ever since I bought the car I rarely had third gear and today on my way from southeastern PA to northwest Ohio seem to pretty much completely lost first unless I really slam it in and fifth likes to disengage every now and then unless I hold the shifter in place both first and fifth were slowly giving me problems until it got really bad after todays 8 hour drive. My transmission code is EBP, is there any other codes I can put in my car from another 2.0 or do I have to get another EBP?
View 2 RepliesI was having an issue with my car not going into boost so I plugged my code reader in and it had 2 codes 1 was p1200 n249 malfunction and the other was diverter valve malfunction so I did the quick easy one and got a new factory diverter valve but it still doesn't go into boost and still reads p1200 n249 what do I need to replace or should I do the n249 bypass it's a bone stock jetta 5 speed.
View 5 RepliesAlright I might have made a major mistake and I need some input; I just recent bought a 2001 Jetta VR6 131k on it and at first I didn't notice so much but since I've gotten. To drive it more I've noticed it's really sluggish on take off and doesn't seem to shift into 4th gear. Also I started noticing a faint rattling noise. And the CEL is on with the codes P0785, P0411 and P1151.
View 1 RepliesSo recently I took my engine apart to do a valve cover gasket and Ecs tuning 2.0 coil conversion. I noticed a good amount of oil in the plug tubes so I got out my trusty soap dispenser and started pumping out oil. Pulled plugs and cleaned them (wanted to make sure oil was all out b4 getting new) also while I had it apart I wanted to take intake off, ( just to polish it and clean out any carbon inside).. Well I never ended up doing that. I removed the injector connections and realized it was to much work for such little satisfaction. So I plugged the injectors back in.
I got my car all back together and now I'm throwing 6 cel codes!! P0102 (maf) which I'm assuming b.c I took it off for so long, p0201, p0202 ( injector 1 and 2 miss), then some misfire codes p0300 (random) p0301 (cylinder 1) and p0304 (cylinder 4). The car starts runs very rough then cel comes on and blinks. I was thinking maybe the oil getting down to the combustion chamber couldn't be the best for it but it would just burn off. Only other thing I did was take off the thottle body and cleaned it.
My car is not boosting. I had two codes p0238 and p0106...
View 9 RepliesI finished installing an auto out of a 1999 beetle into my 2000 golf. I used the beetle TCM now it wont shift out of 3rd. If I manually start in first it will shift up to 3rd but nothing past 3rd. I had it scanned with a generic scanner and these are the codes. P1780, P1783, P0725. I researched the heck out of this and I'm not sure what to do. Do I need to take it and have a vag com hooked up to make sure the ecm and the new tcm are talking? It seems others have had these issues and I thought it might be solenoids but that's not what's coming up.
View 2 RepliesYesterday I purchased an 04 Jetta 2.0 with 179k. It was super cheap and pretty clean. Needs work but I bought it to fix it and daily it. Anyway. When I initially went to look at the car, It started right up. after test driving it, I turned it off to make a deal with the guy. Then started it back up to pull on the trailer. Towed it home, Started right up again to get off the trailer. All was good.
This morning I go out, scan the codes (with an obdII scanner, not vag-com), get the codes, then erase them. Just to get a fresh start at the issues. I go to start the car, and it wont start. Turns over but doesn't fire. Could erasing the codes have done something?
Here's the codes that popped up in case they're important to this situation. P0043, P0102, P3081, P0113. I did scan the codes again after I erased them and it wouldn't start. P0043 is still there.