Dealership put some dye in the oil last week and they're checking it today but they said it seems like it's getting flung around when it hits the axles. Waiting on a loaner because they want to hold it and let it run to see what happens. Whenever I look under it in my garage I see oil buildup on the oil pans passenger side and see a drop about the size of a dime.
View 3 RepliesAs I was loading a bag into the back of my GTI, I noticed water running down the drivers side. It seems to be coming out of where the driver's side back seat belt holder is. It's leaking down into the little compartment as well. Don't know the extent of the damage yet as I haven't had any time to look, The interior ceiling of the car is dry. Leaking into the side compartment as well...
View 3 RepliesYesterday it was the coldest day my car has ever experienced at -27*C or -16F. I only live about 10 minutes from work in stop and go traffic so the car barely reached operating temp as I was arriving to work.
After about 10 hours, I went outside at the end of the day, the temps had warmed slightly and I started the car and let it idle for about 1 minute before driving off. After about 45 seconds I got a series of what seemed to be misfires. The EPC light flashed but eventually turned off, and where the odometer normally appears there was an exclamation point next to a symbol that looked like cruise had been activated. A message appeared in the MFD to the effect of "malfunction - bring car for service"
I reved the car slightly a few times-all seemed good- and left. All was good. Stopped the car a few blocks after and restarted and the warning symbol was gone and all was back to normal.
Today has been warmer and there have been no issues with it.
i have a 2007 gti and this is my first winter with the car and i live in a pretty cold climate and i've noticed quite a bit of white sludge under my oil cap from moisture and oil and i was wondering if there is anything i can do about this and i don't have a catch can and its not coolant i've noticed this happening since about 3 months now (since it went below zero) and my coolant level hasn't moved at all.
View 2 RepliesMy car was just in the shop for the 30K service and the tech noticed quite a bit of oil leaking from the gasket between the CTS pcv system and the engine. He said that because the catch can lacks the ability to release the pressure coming from the engine, it started to eat at the gasket and it now leaks... he recommended that I take the catch can off. I thought the system vented pressure into the intake...
View 3 RepliesI washed the R this past weekend and noticed that hey are covering my car from front to back, and even on the glass. I am looking to perform this work myself.
View 24 RepliesI have a 2004 volkswagen jetta wagon, 2.0l bev engine, 5 spd. I just recently replaced both oxygen sensors due to codes that popped up, but have noticed recently the gas mileage and performance have decreased. Now I get the code 16804 - Catalyst System; Bank 1: Efficiency Below Threshold P0420. The car passed smogged and all the readiness codes passed. One major noticeable different, is when I apply the gas, it is not accerlating like it should.
View 6 RepliesI know it's stupid but rattles and vibrations in an otherwise quiet car drive me absolutely crazy.
So, driving I have noticed this slight non-metallic vibration type noise. It seemed to come and go. So I emptied the car thinking it might be something I was carrying around. No such luck. Turned off the climate control, still there. I had the better half drive while I searched. I could never really see anything but thought it sounded like it might be either in the dash or around the floor area. Totally frustrated I unbuckle my seatbelt and crawl into the passenger floor head first. Nothing on the passenger side. I glance over to the Driver side footwell and notice the slightest vibration from a panel that covers the steering shaft as it goes through the firewall right behind the pedals. Aha! A plastic panel being held in place by 2 plastic type screws that are both loose. i tighten them down with a straight screw driver when I get home and silence! The rattle goes away. You might look at yours as well. I think this might apply to all Mk5 cars. Finding/Fixing a rattle like this for me is like finding money.
I noticed the other day that when i shift to R... the left and right rear view mirror pan out about 5 degrees in their respective direction. Normally when you shift to reverse the mirrors should tilt down. I have looked through all the settings and cannot find any customization options. How you can adjust the rear view mirrors to tilt down? I do not understand why they would pan out as it does nothing to assist you as you reverse.
View 7 RepliesMy passanger side blade has been hitting the side of my windshield randomly since the car was new. Wasn't able to replicate the issue at the dealer so I was pulling the blade off last night to investigate and broke the small square retaining clip (Red arrow). Do the clip assembly (Blue arrow) can be purchased separately or if I have to buy a whole new wiper.
View 4 RepliesMy Drivers side headlight points slightly higher than my passenger side headlight. Is this normal or do I need to adjust, and if so how do I adjust?
View 6 RepliesOk so here's the deal.. A few weeks back I started to notice my passenger side window started to roll slower than the driver side, not by much but its pretty obvious enough every time you either roll the window down or up.. I made an appointment with a VW service center to have them look at it but they said they can't do anything about it .. Is this true ..? The service guy told me that their would be no way to make the motor of the window go any faster or slower.. However I'm back here again due to some clunking/ticking noise every time I roll my pax side window which develop during their first assessment.. So they ordered me a new window regulator which is getting put in now.. The main and initial problem as to why I made an appointment in the first place was for VW service center to fix my pax side window rolling a bit slowly. Now since they are replacing the regulator of my pax side window I asked the service guy whether this would fix the problem of the window rolling slower compare to the driver side and he bluntly said no.. "we cannot make the motor of the window go slower or faster".. Is their any way to fix the rate of the window to go up or down..?
View 6 RepliesI have koni seyup and my car is lowered all the way down all around. my front passenger side sits lower then the driver side.. I also have camber plates in the front. What u think could be the problem.
View 2 RepliesI got under the car today to change the oil and noticed the front drivers side is about an inch lower than the passenger side its causing the inside of my tire to wear very badly.
View 8 RepliesI've just finished installing Driver Side Puddle Lights just under the mirror. I still haven't coded it yet.
[URL]..................... I ran into a problem:
As I want to use the electrical mirrors to adjust my driver side mirror, passenger side mirror moves too. Is it possible that these faults caused by not coded ECU?
I connected ground wire of my LED to blue and black cable connected to the mirror and ran another wire from unit 10 in 16 pin door connector to live wire from my LED.
I have a mkvi gti with all stock suspension except rear sway bar. And I'm right about to order driver gear springs. But have a question about suspension. My rear driver side of the car sits about half inch lower then then rear passenger side on a flat ground. Would this be caused by springs? Or struts? Or what. Planning on ordering the driver gear springs but what the real problem is. I want the driver gear so I'm a bit lowered but not crazy low since the roads in my home town are awful and my street I have to do figure 8's all the way down it to not hit a pot hole.
View 3 RepliesWell my car is crapping out lately,
I put a new steering rack in my mk4 1.8t jetta about a week before I parked it for winter. I went out to the garage yesterday and noticed a pool of PS fluid on the ground, I located one very small leak from the bottom banjo bolt on the rack (needs new crush washers, Was in a rush and didn't have time to pick new ones up :bang head: ).
But the part that confuses me is there is a puddle on/under the passenger side subframe, the rack boot appears to be dry, and I don't believe the new rack is faulty, they are supposed to be all tested and approved before reaching the buyer. and when I turn the car on I can't see a leak anywhere even with the wheel off and a decent view of the rack.
The other day I noticed my passenger side hid was out, so I ordered up a set of bulbs and they arrived a couple days ago. I just finished installing the new bulbs, turned on the lights, and the bulb is still not coming on. I bought these oem hids from 1of1500 right around last Christmas and aside from the pin adaptors being a little ratty, they were in essentially new condition (how sparingly his TR .:R was used and the condition he keeps things in). When we installed the lights they worked, and since have worked without issue. The high beam still works. Is there any chance the 10-12 pin adaptor is to blame here? It is pretty beat up. I can't imagine the ignitor is bad since I've only put 3000 or so miles on the car sine installing the lights.
View 21 RepliesI'm replacing my knock sensors and intake gaskets on a 2001 silverado and there is a lot of carbon buildup in the intake, what can i use to safely clean it with....
View 5 RepliesHeat on HIGH
Drivers side dash vent and defrost will blow fairly warm air, but no where near the 120 it should be on high
Pass side vents ( all ) blow cold air.
Car heats up fine according to the dash gauge and doesn't overhear.
I've run VCDS and there are no fault codes pulling up, so I am at a loss. With the temp being -15 with the wind-chill, it's a damn chilly drive into work. At first I thought it might be the heater core, but that wouldn't explain the split dash issue.
The other day my passenger headlight went out. Today I went to replace it, after much frustration I pulled the bumper and the headlights. I first tried swapping ignitors to see if that was the issue. I went to switch the ballast and now nothing is working except for the passenger high beam. I made an apportionment with the steelership. But I wanted to see if there was anything I maybe able to do to avoid this.
View 1 Replies