Golf mk7 2013 ... All of a sudden I lost the highbeam. Highbeam "flash" still works, but not constant high beam.
Bulbs? Are they separate between flash and constant?
Relay?
Stalk?
I have a 2012 Hyundai Accent GLS and recently noticed that my low beam only works in the high beam setting and the high beam doesn't work.
View 10 RepliesMy roommate has a 2006 S60 Volvo. One day the passenger turn signal just stopped working. It only works if the high beam is on. The driver side turn signal works fine and so do the emergency flashers. It's not the bulb, not the fuse, not the turn signal lever, and she even took it in the shop and they couldn't figure out the problem without replacing the DIM which would cost a lot.
View 1 RepliesI'm trying to troubleshoot an odd issue.
When the lever is in low beam mode I have no headlights or fog lights. (parking lights fine.)
When the lever is forward in high beam mode I have no headlights or fog lights. (parking lights fine.)
But if I hold the lever back in "fash the high beam" mode the high beams turn on. This got me home last night, but I don't know where to start looking for the issue?
Faulty relay? Faulty switch? Something else?
(2004 Santa Fe)
Is there a way to easily disable the high beam DRL on the GT? Last summer I installed the i30 fog lights with DRL built into them and really have no reason to have the high beam DRL not to mention the partially lit halogen high beam looks like garbage in my opinion. Something a little better looking than a partially lit halogen?
View 7 RepliesI was driving and heard a loud SNAP and now there is a constant sound of wind like a fan on high.
View 15 RepliesWhen I use the high beams on my GTI with LP, the pattern goes very high with an oval/round top. The road is lit up fine, but I've never seen a pattern go up so high. Is this normal or a problem.
View 15 RepliesI have a 2013 Accent and have installing driving lights. I am looking for the correct high beam wire on the driver's side on the headlight assembly. I will then run this to a relay so that when I turn on my highs, the driving lights will come on. I have tried to locate the correct wire but the one wire that is hot when the highs are on, is still hot when the car is off as well as the lights.
View 6 RepliesI have a 2013 F150 FX4. When the temperature is below 45 and the truck is cold the right high beam wont turn off if used, until the truck engine is warmed up.
View 6 RepliesI have a 2012 gti with oem bi-xenon head lights. What code or setting do you use on vagcom to bring on the fog lights when I turn on highbeam?
View 3 RepliesMy car is fully stock, with all options available to me (cold weather package not available here). The low-beam triple-LED headlights are aimed way too low compared to all my previous cars, and where they should be. BUT high-beam is aimed properly. So if I adjust the low-beams up, my high-beams might end up lighting up the trees, not the road.
If adjust the headlights up on a fully stock car (not lowered at the front)? Are the high beams still lighting up the road fine? And if you can be specific as the number of turns on the screwdriver, it'd be good too to have an initial adjustment reference.
This morning a dash light informed me a headlight bulb was out. It was my DTR light on the passenger side.
I purchased Sylvania H7 high intensity, installed it and it failed to work properly. Daytime light on only drivers side works.
High Beam on , both lights works.
I checked my manual and it said to check fuse in the 5 slot on the driver side dash/door panel and there actually is no fuse in there. I checked the driver side and there was no fuse there either.
I replaced my driver side bulb last year and it took 5 mins....i am already 4 hours into this!
I drive a 96 Subaru Legacy. What does it mean when one of the high beams is dimmer (less light output) than the low beam? I am using a brand-new bulb. It's not an adjustment issue because I was looking at the bulb when it was outside of the housing and it clearly gets dimmer when you switch to brights. However, they are equally bright when on low-beam, so I don't think its just a crossed wire.
View 2 RepliesI replaced the low beam and high beam on my Subaru, now the low beam is very dim and the high beam doesn't work. Careful not to touch the bulb.
View 3 RepliesI have been trying to sort this issue for a while now to no avail. I have had my MKV .:R since February and this problem has existed since I bought it. If the headlight switch is in the "off" position, my lights are off. That is good.
So far, whenever the switch is switched to "auto," the light are ALWAYS on. That doesn't bother me at all, but it seems wrong. Obviously, when it is in the "on: position, they're also on.
Now the problem I have encountered is whenever the lights are on (ie not in the "off" position) the driver's side light is always on the "high" position, even if my brights are not flicked on. The passenger light switches from low to high according to whether I have the brights flicked on or off.
I have 2000 golf with a gli front end. Recently just did the swap and now I'm having issues with one blinker and one high beam not working. The running lights work on both sides. The headlights work on both sides. I checked the bulbs and they were good. I check for power it was all good. I checked the fuses and they were fine.
View 7 RepliesI installed a headlight kit from VW tuning a while back d2s with 6k bulbs I believe.
The headlights work but my high beam indicator is stuck on. I know this is a common problem but for the life of me I can't figure out how to fix it. If I switch back and forth with the stick on the column it does nothing. Just stays on high beams. I've just kind of dealt with it for a while.
So i just purchased a 2008 R32 "united grey" US modelit has a clean 65,000 miles.... upon driving it home i flicked on the brights after about 10 seconds they automatically dimmed and the bulb indicator light popped on i researched and was confused about so many combated responses, and gathered that the brights operated off the same bulb as the low beams which both work "HID'S OEM" and that the two inside useless lights are flash to pass and can be enabled using VAG COM.....
But back to the task at hand i lined up to a wall and put my brights on and the passenger doesn't change in intensity or even do anything but stay on low beam my drivers side works fine! i checked fuses and saw none that looked blown but also didn't know if the brights were even on a separate fuse nor what " numeric position" it would be in?
Do I just need a new OEM bulb? new fuse? I haven't tried swapping the bulbs yet from drivers to passenger vise veresa... nor do i even know for sure if high beams work off of the same light, or if there is a mysterious spot for the highbeam bulb i not see
So tonight I went to turn my fan on for my heat when I started my car and noticed it is will only work when it is on the highest speed (4 I think). What the issue could be?
View 10 RepliesI notice that when I pull the turnsignal switch, the "flash-to-pass" lights are considerably brighter than when I lock the switch forward for regular hi-beam. Questions:
1) does it hurt anything if you drive for a few minutes manually holding the switch towards you?
2) is there an easy wiring mod. to make the locked-on hi beams extra bright like the passing lights?
Why buy bulb upgrades if the stock ones are capable of xtra brightness? (I drive through a remote area daily in the dark that is rich with deer, and I am usually the only vehicle.)
I have a 2006 elantra. I just got it back from having a new clutch put in. My passenger side headlight, low beam, no longer works. I tried two different new bulbs and it still doesn't work. All the other lights on the car are working, including the high beam and running light on the passenger side. Is there something that would have been disconnected when they replaced the clutch? Is there something I should check?
View 1 Replies